Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY (for RHD)

STEERING COLUMN ASSEMBLY (for RHD) > REASSEMBLY

for Preparation Click here



1. INSTALL POWER STEERING MOTOR ASSEMBLY

NOTICE:
  1. Do not drop the power steering motor assembly, strike it with tools or subject it to impacts.
  2. If the power steering motor assembly is subjected to an impact, replace it with a new one.
  3. Do not pull the wire harness and tilt steering support bond cable of the power steering motor assembly.
  4. Do not allow any moisture to come into contact with the power steering motor assembly.
  5. Do not loosen any bolts not mentioned in the procedure.
  6. Do not allow any foreign objects to contaminate the power steering motor assembly.



    C234657
  1. Apply grease to the serrated part of the electric power steering column sub-assembly.

    NOTICE:
    First wipe off the existing grease from the serrated part, and then apply the dedicated grease supplied with a new power steering motor assembly or electric power steering column sub-assembly.

  1. Temporarily install the power steering motor assembly to the electric power steering column sub-assembly with the 2 bolts.

    NOTICE:
    When temporarily installing the 2 bolts to the power steering motor assembly, do not tighten them all the way down.



    C234658E01
  1. Secure the steering column assembly in a vise using aluminum plates and a piece of cloth.
    Text in Illustration 
    *1
    Wooden Block

    NOTICE:
    1. Do not overtighten the vise, as the steering column assembly may become deformed.
    2. Secure the power steering motor assembly so that it is directly upright.
    3. Support the steering column assembly with a wooden block or similar item to ensure that it does not fall.



    C234659E01
  1. Using SST, turn the steering main shaft once 180 degrees to the left and then 180 degrees to the right at a speed of 60 rpm, and repeat 2 to 3 times to adjust the axis centering of the power steering motor assembly.

    SST
    09616-00011  

  1. Tighten the 2 bolts.

    Torque:
    19 N*m{ 189 kgf*cm , 14 ft.*lbf }



    C234660E01
  1. Using SST, measure the turning torque of the steering main shaft.

    SST
    09616-00011  

    Torque:
    Turning torque:
    1.45 N*m{ 14.8 kgf*cm , 12.8 in.*lbf } or less

    NOTICE:
    Ensure that there is no abnormal resistance during rotation.

    If the torque is not as specified, readjust the axis centering of the power steering motor assembly.



  1. Install 2 new clamps and tape to the wire harness as shown in the illustration.


    C234661E02


    Text in Illustration 
    *1
    Power Steering Motor Wire Harness
    *2
    Torque Sensor Wire Harness
    *3
    Tape A
    *4
    No. 3 Clamp
    *5
    Tape B
    *6
    No. 2 Clamp
    *a
    358 to 378 mm
    *b
    152 to 168 mm
    *c
    60 to 100 mm
    *d
    80 to 100 mm
    *e
    373 to 393 mm
    *f
    105 mm

    NOTICE:
    Wrap the tape at least 1.5 turns.



    C234662
  1. Pass the torque sensor wire harness through the cutout of a new protector.



    C235438
  1. Engage the clamp and install the protector to the steering column assembly.

    NOTICE:
    Make sure the wire harness is not pinched between the protector and the steering column assembly.



    C234663
  1. Engage No. 2 clamp and install the wire harness to the protector.



    C234664E01
  1. Pass a new No. 1 clamp through the groove in the protector, and tighten it within area A shown in the illustration to secure the protector and wire harness to the power steering motor assembly.

    NOTICE:
    Make sure there is no rattling or looseness in the protector.

    HINT:
    1. Fastening power for No. 1 clamp: 200 N (20 kgf)
    2. Coat the protector with paint.

  1. Cut off the excess length of No. 1 clamp.



2. INSTALL NO. 1 STEERING COLUMN PROTECTOR (for Manual Transaxle)
  1. Install the No. 1 steering column protector with the bolt.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }



3. INSTALL IGNITION OR STARTER SWITCH ASSEMBLY
  1. Engage the 2 claws to install the ignition or starter switch assembly onto the upper steering column bracket assembly.



4. INSTALL KEY INTER LOCK SOLENOID (for Automatic Transaxle)
  1. Install the key inter lock solenoid onto the upper steering column bracket assembly with the screw.



5. INSTALL UN-LOCK WARNING SWITCH ASSEMBLY


C233276
  1. Engage the 2 claws to install the un-lock warning switch assembly onto the upper steering column bracket assembly.

    HINT:
    Slide the un-lock warning switch assembly, in the direction shown by the arrow in the illustration, to install it.



6. INSTALL IGNITION SWITCH LOCK CYLINDER ASSEMBLY
  1. Turn the ignition switch to ACC.



    C233277
  1. Install the ignition switch lock cylinder assembly into the upper steering column bracket assembly.

  1. Make sure that the ignition switch lock cylinder assembly is securely fixed onto the ignition switch lock cylinder assembly.



7. INSTALL UPPER STEERING COLUMN BRACKET ASSEMBLY
  1. Set the steering column assembly in a vise between aluminum plates.

    NOTICE:
    Do not overtighten the vise.



    C233278
  1. Install the steering column upper with switch bracket assembly with a new steering lock set bolt, and then tighten the bolt until its head comes off.



8. INSTALL TILT STEERING SUPPORT BOND CABLE
  1. Install the tilt steering support bond cable with the 2 screws.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }



9. INSTALL NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY


  1. Align the matchmarks on the No. 2 steering intermediate shaft assembly and the steering column assembly and provisionally install them with the bolt.

    HINT:
    C236078E01
    When either the steering column assembly or the No. 2 steering intermediate shaft assembly is replaced with a new one, they have no matchmarks, so align the marking (pink) on the steering column assembly shaft with the slit of the No. 2 steering intermediate shaft assembly, and install them.

    Text in Illustration 
    *a
    Marking (Pink)
    *b
    Slit



10. INSTALL STEERING SLIDING YOKE SUB-ASSEMBLY


    C232525E01
  1. Align the matchmarks on the No. 2 steering intermediate shaft assembly and the steering sliding yoke and provisionally install them with the bolt.
    Text in Illustration 
    *a
    Matchmark