FRONT SUSPENSION MEMBER > REMOVAL |
| 1. POSITION FRONT WHEELS FACING STRAIGHT AHEAD |
| 2. REMOVE COLUMN HOLE COVER SILENCER SHEET |
![]() |
Remove the 2 clips and the column hole cover silencer sheet.
| 3. SEPARATE STEERING SLIDING YOKE SUB-ASSEMBLY |
![]() |
Use a seat belt to fix the steering wheel assembly, in order to avoid breakage of the spiral cable.
![]() |
Place matchmarks on the steering sliding yoke sub-assembly and the steering gear assembly.
| *1 | Steering Sliding Yoke Sub-assembly |
| *a | Matchmark |
Loosen bolt A, remove bolt B and separate the steering sliding yoke sub-assembly from the steering gear assembly.
| 4. SEPARATE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY |
![]() |
Remove clip A, separate clip B from the body and separate the No. 1 steering column hole cover sub-assembly.
| 5. REMOVE FRONT WHEEL |
| 6. REMOVE ENGINE UNDER COVER SUB-ASSEMBLY (for Metal Type) |
| 7. SEPARATE FRONT STABILIZER LINK ASSEMBLY LH |
![]() |
Remove the nut and separate the stabilizer link assembly LH from the front stabilizer bar.
| 8. SEPARATE FRONT STABILIZER LINK ASSEMBLY RH |
| 9. SEPARATE TIE ROD END SUB-ASSEMBLY LH |
Remove the cotter pin and castle nut.
![]() |
Install SST to the threaded section of the tie rod end.
Using SST, separate the tie rod end from the front axle assembly.

| *a | Place the wrench here | - | - |
![]() | Apply grease to the bolt threads and the tip of SST. | - | - |
| 10. SEPARATE TIE ROD END SUB-ASSEMBLY RH |
| 11. SEPARATE FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY LH |
Remove the clip and castle nut.
![]() |
Install SST to the threaded section of the lower ball joint.
Using SST, separate the lower arm.

| *a | Place the wrench here | - | - |
![]() | Apply grease to the bolt threads and the tip of SST. | - | - |
| 12. SEPARATE FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY RH |
| 13. SUSPEND ENGINE ASSEMBLY (for Automatic Transaxle) |
![]() |
On a flat location, set the attachment, plate lift attachment, and wooden block in the positions shown in the figure, and set the engine assembly.
![]() | Attachment Placement Positions |
| 14. SUSPEND ENGINE ASSEMBLY (for Manual Transaxle) |
![]() |
On a flat location, set the attachment, plate lift attachment, and wooden block in the positions shown in the figure, and set the engine assembly.
![]() | Attachment Placement Positions |
| 15. REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY |
![]() |
Remove the bolt and separate the engine moving control rod.
![]() |
Place wooden blocks or plate lift attachments in the positions shown in the illustration and set an engine lifter underneath the front suspension crossmember sub-assembly.
![]() | Front of the Vehicle |
![]() | Attachment Placement Positions |
![]() |
Remove the 6 bolts and front suspension crossmember sub-assembly.
| 16. REMOVE MANUAL STEERING GEAR |
![]() |
Remove the 2 bolts, 2 nuts and the manual steering gear from the front suspension crossmember.
| 17. REMOVE FRONT NO. 1 STABILIZER BRACKET LH |
![]() |
Remove the 2 bolts and the front No. 1 stabilizer bracket LH.
| 18. REMOVE FRONT NO. 1 STABILIZER BRACKET RH |
| 19. REMOVE FRONT STABILIZER BAR |
| 20. REMOVE FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY LH |
![]() |
Remove the bolt and the front lower suspension arm sub-assembly LH.
| 21. REMOVE FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY RH |
| 22. REMOVE ENGINE MOVING CONTROL ROD |
![]() |
Remove the bolt and the engine moving control rod.