Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING PRESSURE SENSOR

AIR CONDITIONING PRESSURE SENSOR > ON-VEHICLE INSPECTION

for Preparation Click here



1. INSPECT AIR CONDITIONER PRESSURE SENSOR (for Manual Air Conditioning System)


    E208778E03
  1. Check the wire harness.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Air Conditioner Pressure Sensor)

    1. Disconnect the A23 air conditioner pressure sensor connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      A23-1 (-) - Body ground
      Always
      Below 1 Ω

    3. Turn the ignition switch to ON.

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      A23-3 (+) - Body ground
      Ignition switch ON
      4.75 to 5.25 V



    I106305E01
  1. Check the air conditioner pressure sensor.
    Text in Illustration 
    *a
    Component with harness connected
    (Air Conditioning Amplifier Assembly)

    1. Set the manifold gauge.

    2. Connect the connector to the air conditioner pressure sensor.

    3. Warm up the engine.

    4. A/C switch on.

    5. Using a voltmeter, measure the voltage between connector terminals 7 (PRE) and 5 (SG-2) of the air conditioning amplifier assembly.

      HINT:
      Check from the rear of the connector while it is connected to the air conditioning amplifier assembly.

      Standard Voltage:
      Tester Connection
      Refrigerant Pressure
      Specified Condition
      F41-7 (PRE) - F41-5 (SG-2)
      0.196 to 3.14 MPa
      (2.0 to 32 kgf/cm2, 28 to 455 psi)
      0.66 to 4.88 V



2. INSPECT AIR CONDITIONER PRESSURE SENSOR (for Automatic Air Conditioning System)


    E208778E03
  1. Check the wire harness.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Air Conditioner Pressure Sensor)

    1. Disconnect the connector of the air conditioner pressure sensor.

    2. Using an ohmmeter, measure the resistance of the wire harness side connector.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      A23-1 (-) - Body ground
      Always
      Below 1 Ω

    3. Turn the ignition switch to ON.

    4. Measure the voltage of the wire harness side connector.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      A23-3 (+) - Body ground
      Ignition switch ON
      4.75 to 5.25 V



    I106306E01
  1. Check the air conditioner pressure sensor.
    Text in Illustration 
    *a
    Component with harness connected
    (Air Conditioning Amplifier Assembly)

    1. Set the manifold gauge.

    2. Connect the connector to the air conditioner pressure sensor.

    3. Warm up the engine.

    4. A/C switch on.

    5. Using a voltmeter, measure the voltage between connector terminals 9 (PRE) and 13 (SG-2) of the air conditioning amplifier assembly.

      HINT:
      Check from the rear of the connector while it is connected to the air conditioning amplifier assembly.

      Standard Voltage:
      Tester Connection
      Refrigerant Pressure
      Specified Condition
      F42-9 (PRE) - F42-13 (SG-2)
      0.196 to 3.14 MPa
      (2.0 to 32 kgf/cm2, 28 to 455 psi)
      0.66 to 4.88 V