Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM

ENGINE IMMOBILISER SYSTEM > Security Indicator Light Does not Blink

for Preparation Click here


DESCRIPTION

  1. When the engine immobiliser system is set, the theft warning indicator light assembly blinks continuously, but does not illuminate if the engine immobiliser system is not set.

WIRING DIAGRAM


B271399E02


INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  2. When replacing the transponder key ECU assembly, refer to the Service Bulletin.

1.CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC is not output.



NG
GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)
OK


2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SECURITY INDICATOR)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Immobiliser / Active Test.

  1. According to the display on the intelligent tester, perform the Active Test.

    Immobiliser 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Security Indicator
    Theft warning indicator light assembly
    OFF / ON
    -

    OK:
    Theft warning indicator light assembly can be turned on and off using the intelligent tester.



NG
Go to step 4
OK


3.READ VALUE USING INTELLIGENT TESTER (ENGINE IMMOBILISER SYSTEM STATUS)
  1. Turn the ignition switch off.

    HINT:
    When using the intelligent tester with the ignition switch off to troubleshoot: Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 second until communication between the intelligent tester and vehicle begins.

  1. Using the intelligent tester, read the Data List (Click here).

    Immobiliser 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Immobiliser
    Engine immobiliser system status determined by transponder key ECU assembly / Set or Unset
    Set: Engine immobiliser set (engine start prohibited [no key in ignition key cylinder])
    Unset: Engine immobiliser unset (engine start permitted [key inserted in ignition key cylinder])
    When the engine immobiliser system does not change to the unset state, this item can be used to determine if the cause is the transponder key ECU assembly.



NG
Go to step 6
OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY 

4.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - THEFT WARNING INDICATOR LIGHT ASSEMBLY)
  1. Disconnect the F54 transponder key ECU assembly connector.

  1. Disconnect the F56 theft warning indicator light assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F54-8 (IND) - F56-2 (LP)
    Always
    Below 1 Ω
    F56-6 (E) - Body ground
    Always
    Below 1 Ω
    F54-8 (IND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT THEFT WARNING INDICATOR LIGHT ASSEMBLY
  1. Inspect the theft warning indicator light assembly (Click here).



NG
REPLACE THEFT WARNING INDICATOR LIGHT ASSEMBLY (Click here)
OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY 

6.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - BATTERY AND BODY GROUND)


    B242622E11
  1. Disconnect the F54 transponder key ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F54-16 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    F54-1 (+B) - Body ground
    Always
    11 to 14 V
    F54-2 (IG) - Body ground
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V

Text in Illustration 
*a
Front view of wire harness connector
(to Transponder Key ECU Assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY