Home › Drivetrain · U340E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM

AUTOMATIC TRANSAXLE SYSTEM > TERMINALS OF ECM

for Preparation Click here



ECM

C105085E12

HINT:
The standard voltage and resistance of each ECM terminal is shown in the table below.
In the table, first follow the information under "Condition". Look under "Terminal No. (Symbol) " for the terminals to be inspected. The standard voltage and resistance between the terminals is shown under "Specific Condition".
Use the illustration above as a reference for the ECM terminals.


Terminals No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
A74-1 (+B2) - B84-104 (E1)
B - W-B
Power source of ECM
Ignition switch ON
11 to 14 V
A74-2 (+B) - B84-104 (E1)
B - W-B
Power source of ECM
Ignition switch ON
11 to 14 V
A74-20 (BATT) - B84-104 (E1)
Y - W-B
Battery (for measuring battery voltage and for ECM memory)
Always
11 to 14 V
A74-26 (3) - B84-104 (E1)
BE - W-B
3 shift position switch signal
Ignition switch ON and shift lever in 3
11 to 14 V
Ignition switch ON and shift lever not in 3
Below 1 V
A74-41 (CANH) - B84-104 (E1)
L - W-B
CAN communication line
Ignition switch ON
Pulse generation
(See waveform 1)
A74-49 (CANL) - B84-104 (E1)
W - W-B
CAN communication line
Ignition switch ON
Pulse generation
(See waveform 2)
B84-104 (E1) - Body ground
W-B
Ground
Always
Below 1 Ω
B84-52 (NSW) - B84-104 (E1)
BE - W-B
Park/Neutral position switch signal
Ignition switch ON and shift lever in P or N
Below 1 V
Ignition switch ON and shift lever not in P and N
11 to 14 V
B84-53 (R) - B84-104 (E1)
R - W-B
R shift position switch signal
Ignition switch ON and shift lever in R
11 to 14 V
Ignition switch ON and shift lever not in R
Below 1 V
B84-54 (N) - B84-104 (E1)
V - W-B
N shift position switch signal
Ignition switch ON and shift lever in N
11 to 14 V
Ignition switch ON and shift lever not in N
Below 1 V
B84-55 (2) - B84-104 (E1)
LG - W-B
2 shift position switch signal
Ignition switch ON and shift lever in 2
11 to 14 V
Ignition switch ON and shift lever not in 2
Below 1 V
B84-56 (D) - B84-104 (E1)
L - W-B
D shift position switch signal
Ignition switch ON and shift lever in D or 3
11 to 14 V
Ignition switch ON and shift lever not in D and 3
Below 1 V
B84-57 (SL) - B84-104 (E1)
P - W-B
SL solenoid signal
Ignition switch ON
Below 1 V
Vehicle driving under lock up range
11 to 14 V
B84-72 (THO1) - B84-95 (ETHO)
Y - B
ATF (Automatic Transmission Fluid) temperature sensor signal
ATF temperature: 10°C
(50°F) to 145°C (293°F)
4 to 0 V
B84-73 (P) - B84-104 (E1)
P - W-B
P shift position switch signal
Ignition switch ON and shift lever in P
11 to 14 V
Ignition switch ON and shift lever not in P
Below 1 V
B84-74 (L) - B84-104 (E1)
V - W-B
L shift position switch signal
Ignition switch ON and shift lever in L
11 to 14 V
Ignition switch ON and shift lever not in L
Below 1 V
B84-76 (SLT+) - B84-75 (SLT-)
P - L
Shift solenoid valve SLTsignal
Engine idling speed
Pulse generation
B84-78 (S2) - B84-104 (E1)
L - W-B
Shift solenoid valve S2 signal
Ignition switch ON
Below 1 V
1st or 4th gear
11 to 14 V
2nd or 3rd gear
Below 1 V
B84-79 (S1) - B84-104 (E1)
R - W-B
Shift solenoid valve S1 signal
Ignition switch ON
11 to 14 V
1st or 2nd gear
11 to 14 V
3rd or 4th gear
Below 1 V
B84-80 (ST) - B84-104 (E1)
GR - W-B
Shift solenoid valve ST signal
Shift lever in D (3rd gear ←→ 4th gear)
Below 1 V ←→ 11 to 14 V
B84-125 (NT+) - B84-124 (NT-)
L - G
Transmission revolution sensor (NT) signal
Driving at approximately 20 km/h (12 mph)
Pulse generation
(See waveform 3)


    C193943E02
  1. Waveform 1
    Terminal
    CANH - E1
    Tool setting
    1 V/DIV, 10 μs/DIV
    Vehicle conditions
    Ignition switch ON



  2. C193942E02
  3. Waveform 2
    Terminal
    CANL - E1
    Tool setting
    1 V/DIV, 10 μs/DIV
    Vehicle conditions
    Ignition switch ON



  4. C053419E18
  5. Waveform 3
    Terminal
    NT+ - NT-
    Tool setting
    2 V/DIV, 1 ms/DIV
    Vehicle conditions
    Driving at approximately 20 km/h (12 mph)