AUTOMATIC TRANSAXLE SYSTEM > DATA LIST / ACTIVE TEST |
| DATA LIST |
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.
In accordance with the display on the tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| N Range Status | Judgment for shift lever N position/ OFF or ON |
| - |
| Neutral Position SW Signal | PNP switch Status/ OFF or ON |
| When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect.
|
| Stop Light Switch | Stop light switch status/ OFF or ON |
| - |
| SPD (NT) | Input turbine speed/ display: 50 rpm min.: 0 rpm max.: 12750 rpm |
| - |
| Shift SW Status (P Range) | PNP switch Status/ OFF or ON |
| When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect.
|
| Shift SW Status (R Range) | PNP switch Status/ OFF or ON |
| |
| Shift SW Status (2 Range) | PNP switch Status/ OFF or ON |
| |
| Shift SW Status (L Range) | PNP switch Status/ OFF or ON |
| |
| Shift SW Status (N Range) | PNP switch Status/ OFF or ON |
| |
| Shift SW Status (D Range) | PNP switch Status/ OFF or ON |
| |
| Shift SW Status (3 Range) | PNP switch Status/ OFF or ON |
| |
| A/T Oil Temperature 1 | ATF temperature Sensor Value/ min.: -40°C (-40°F) max.: 215°C (419°F) |
| If the value is "-40°C (-40°F)" or "150°C (302°F) or more ", ATF temperature sensor circuit is opened or shorted. |
| Lock Up | Lock Up status/ OFF or ON |
| - |
| ST Solenoid Status | Shift Solenoid ST Status/ OFF or ON | OFF → ON → OFF: Up-shifting and down-shifting between 3rd and 4th gears while driving | - |
| Shift Status | Actual Gear Position/ 1st, 2nd, 3rd or 4th | Same as actual gear | - |
| SLT Solenoid Status | Shift Solenoid SLT Status/ OFF or ON |
| - |
| SL Solenoid Status | Shift Solenoid SL Status/ OFF or ON |
| - |
| ACTIVE TEST |
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Select the following items: Powertrain / Engine and ECT / Active Test.
In accordance with the display on the tester, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Activate the Solenoid (SLT)* | [Test Details] Operate shift solenoid SLT and raise the line pressure.
| ON/OFF | [Vehicle Condition]
|
| Activate the Solenoid (S1) | [Test Details] Operate shift solenoid S1 | ON/OFF | [Vehicle Condition]
|
| Activate the Solenoid (S2) | [Test Details] Operate shift solenoid S2 | ON/OFF | [Vehicle Condition]
|
| Activate the Lock Up | [Test Details] Control shift solenoid SL to set automatic transaxle to lock-up condition. | ON/OFF | Possible to check SL operation. [Vehicle Condition] Vehicle speed: 60 km/h (36 mph) or more, and 4th gear |
| Activate the Solenoid (SL) | [Test Details] Operate shift solenoid SL | ON/OFF | [Vehicle Condition]
|
| Control the Shift Position | [Test Details] Operate shift solenoid valve and set each shift position manually. [Others]
| 1st/2nd/3rd/4th | Possible to check operation of shift solenoid valves. [Vehicle Condition] Vehicle speed: Less than 50 km/h (30 mph) |
| Activate the Solenoid (ST) | [Test Details] Operate shift solenoid ST | ON/OFF | [Vehicle Condition]
|