DTC B161C/9A Lost Communication with Front Satellite Sensor Bus Center |
DTC B161D/9A Front Satellite Sensor Bus Center Initialization Incomplete |
| DTC No. | DTC Detection Condition | Trouble Area |
| B161C/9A B161D/9A |
|
|

| 1.CHECK CONNECTORS |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Check that the connectors are properly connected to the airbag sensor assembly and front airbag sensor. Also check that the connectors that link the engine room main wire and instrument panel wire are properly connected.
Disconnect the connectors from the airbag sensor assembly and front airbag sensor. Also disconnect the connectors that link the engine room main wire and instrument panel wire.
Check that the terminals of connectors are not damaged.
|
| ||||
| OK | |
| 2.CHECK FRONT AIRBAG SENSOR CIRCUIT (OPEN) |
Connect the connectors that link the engine room main wire and instrument panel wire.

| *1 | Front Airbag Sensor | *2 | Airbag Sensor Assembly |
| *3 | Connector B | *4 | Connector E |
| *5 | Service Wire | - | - |
| *a | Front view of wire harness connector (to Airbag Sensor Assembly) | *b | Front view of wire harness connector (to Front Airbag Sensor) |
Using a service wire, connect terminals 30 (+SL) and 28 (-SL) of connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A20-2 (+SL) - A20-1 (-SL) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 3.CHECK FRONT AIRBAG SENSOR CIRCUIT (SHORT) |
![]() |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A20-2 (+SL) - A20-1 (-SL) | Always | 1 MΩ or higher |
| *1 | Front Airbag Sensor |
| *2 | Airbag Sensor Assembly |
| *3 | Connector E |
| *a | Front view of wire harness connector (to Front Airbag Sensor) |
|
| ||||
| OK | |
| 4.CHECK FRONT AIRBAG SENSOR CIRCUIT (SHORT TO B+) |
![]() |
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A20-2 (+SL) - Body ground | Ignition switch ON | Below 1 V |
| A20-1 (-SL) - Body ground | Ignition switch ON | Below 1 V |
| *1 | Front Airbag Sensor |
| *2 | Airbag Sensor Assembly |
| *3 | Connector E |
| *a | Front view of wire harness connector (to Front Airbag Sensor) |
|
| ||||
| OK | |
| 5.CHECK FRONT AIRBAG SENSOR CIRCUIT (SHORT TO GROUND) |
![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A20-2 (+SL) - Body ground | Always | 1 MΩ or higher |
| A20-1 (-SL) - Body ground | Always | 1 MΩ or higher |
| *1 | Front Airbag Sensor |
| *2 | Airbag Sensor Assembly |
| *3 | Connector E |
| *a | Front view of wire harness connector (to Front Airbag Sensor) |
|
| ||||
| OK | |
| 6.CHECK FRONT AIRBAG SENSOR |
Connect the connector to the airbag sensor assembly.
Temporarily replace the front airbag sensor with a new one.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B161C/9A or B161D/9A is not output. | A |
| DTC B161C/9A or B161D/9A is output. | B |
Reinstall the former front airbag sensor, and connect the connector.
|
| ||||
| A | ||
| ||
| 7.CHECK INSTRUMENT PANEL WIRE (OPEN) |
Disconnect the instrument panel wire connector from the engine room main wire.

| *1 | Front Airbag Sensor | *2 | Airbag Sensor Assembly |
| *3 | Engine Room Main Wire | *4 | Instrument Panel Wire |
| *5 | Connector B | *6 | Connector C |
| *7 | Service Wire | - | - |
| *a | Front view of wire harness connector (to Airbag Sensor Assembly) | *b | Front view of wire harness connector (to Engine Room Main Wire) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| AF1-1 (+SL) - AF1-2 (-SL) | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||
| 8.CHECK INSTRUMENT PANEL WIRE (SHORT) |
![]() |
Disconnect the instrument panel wire connector from the engine room main wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| AF1-1 (+SL) - AF1-2 (-SL) | Always | 1 MΩ or higher |
| *1 | Front Airbag Sensor |
| *2 | Airbag Sensor Assembly |
| *3 | Engine Room Main Wire |
| *4 | Instrument Panel Wire |
| *5 | Connector C |
| *a | Front view of wire harness connector (to Engine Room Main Wire) |
|
| ||||
| OK | ||
| ||
| 9.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+) |
![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Disconnect the instrument panel wire connector from the engine room main wire.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| AF1-1 (+SL) - Body ground | Ignition switch ON | Below 1 V |
| AF1-2 (-SL) - Body ground | Ignition switch ON | Below 1 V |
| *1 | Front Airbag Sensor |
| *2 | Airbag Sensor Assembly |
| *3 | Engine Room Main Wire |
| *4 | Instrument Panel Wire |
| *5 | Connector C |
| *a | Front view of wire harness connector (to Engine Room Main Wire) |
|
| ||||
| OK | ||
| ||
| 10.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND) |
![]() |
Disconnect the instrument panel wire connector from the engine room main wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| AF1-1 (+SL) - Body ground | Always | 1 MΩ or higher |
| AF1-2 (-SL) - Body ground | Always | 1 MΩ or higher |
| *1 | Front Airbag Sensor |
| *2 | Airbag Sensor Assembly |
| *3 | Engine Room Main Wire |
| *4 | Instrument Panel Wire |
| *5 | Connector C |
| *a | Front view of wire harness connector (to Engine Room Main Wire) |
|
| ||||
| OK | ||
| ||