Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM (w/ VSC/Separate Type Yaw Rate Sensor)

DTC    B161C/9A    Lost Communication with Front Satellite Sensor Bus Center

DTC    B161D/9A    Front Satellite Sensor Bus Center Initialization Incomplete

for Preparation Click here


DESCRIPTION

The front airbag sensor circuit consists of the airbag sensor assembly and front airbag sensor.
The front airbag sensor detects impacts to the vehicle and sends signals to the airbag sensor assembly to determine if the airbag should be deployed.
These DTCs are stored when a malfunction is detected in the front airbag sensor circuit.

DTC No.
DTC Detection Condition
Trouble Area
B161C/9A
B161D/9A
  1. The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the front airbag sensor circuit.
  2. Front airbag sensor malfunction
  3. Airbag sensor assembly malfunction
  1. Instrument panel wire
  2. Engine room main wire
  3. Front airbag sensor
  4. Airbag sensor assembly

WIRING DIAGRAM


C234055E02


INSPECTION PROCEDURE

1.CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the airbag sensor assembly and front airbag sensor. Also check that the connectors that link the engine room main wire and instrument panel wire are properly connected.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the airbag sensor assembly and front airbag sensor. Also disconnect the connectors that link the engine room main wire and instrument panel wire.

  1. Check that the terminals of connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE WIRE HARNESS
OK


2.CHECK FRONT AIRBAG SENSOR CIRCUIT (OPEN)


  1. Connect the connectors that link the engine room main wire and instrument panel wire.


    C249139E02


    Text in Illustration 
    *1
    Front Airbag Sensor
    *2
    Airbag Sensor Assembly
    *3
    Connector B
    *4
    Connector E
    *5
    Service Wire
    -
    -
    *a
    Front view of wire harness connector
    (to Airbag Sensor Assembly)
    *b
    Front view of wire harness connector
    (to Front Airbag Sensor)

  1. Using a service wire, connect terminals 30 (+SL) and 28 (-SL) of connector B.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A20-2 (+SL) - A20-1 (-SL)
    Always
    Below 1 Ω



NG
Go to step 7
OK


3.CHECK FRONT AIRBAG SENSOR CIRCUIT (SHORT)


    C249136E03
  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A20-2 (+SL) - A20-1 (-SL)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Front Airbag Sensor
    *2
    Airbag Sensor Assembly
    *3
    Connector E
    *a
    Front view of wire harness connector
    (to Front Airbag Sensor)



NG
Go to step 8
OK


4.CHECK FRONT AIRBAG SENSOR CIRCUIT (SHORT TO B+)


    C249136E03
  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A20-2 (+SL) - Body ground
    Ignition switch ON
    Below 1 V
    A20-1 (-SL) - Body ground
    Ignition switch ON
    Below 1 V

    Text in Illustration 
    *1
    Front Airbag Sensor
    *2
    Airbag Sensor Assembly
    *3
    Connector E
    *a
    Front view of wire harness connector
    (to Front Airbag Sensor)



NG
Go to step 9
OK


5.CHECK FRONT AIRBAG SENSOR CIRCUIT (SHORT TO GROUND)


    C249136E03
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A20-2 (+SL) - Body ground
    Always
    1 MΩ or higher
    A20-1 (-SL) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Front Airbag Sensor
    *2
    Airbag Sensor Assembly
    *3
    Connector E
    *a
    Front view of wire harness connector
    (to Front Airbag Sensor)



NG
Go to step 10
OK


6.CHECK FRONT AIRBAG SENSOR
  1. Connect the connector to the airbag sensor assembly.

  1. Temporarily replace the front airbag sensor with a new one.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B161C/9A or B161D/9A is not output.
    A
    DTC B161C/9A or B161D/9A is output.
    B

    HINT:
    Codes other than DTCs B161C/9A and B161D/9A may be output at this time, but they are not related to this check.

  1. Reinstall the former front airbag sensor, and connect the connector.



B
REPLACE AIRBAG SENSOR ASSEMBLY (Click here)
A

END (FRONT AIRBAG SENSOR WAS DEFECTIVE) 

7.CHECK INSTRUMENT PANEL WIRE (OPEN)


  1. Disconnect the instrument panel wire connector from the engine room main wire.


    C251210E01


    Text in Illustration 
    *1
    Front Airbag Sensor
    *2
    Airbag Sensor Assembly
    *3
    Engine Room Main Wire
    *4
    Instrument Panel Wire
    *5
    Connector B
    *6
    Connector C
    *7
    Service Wire
    -
    -
    *a
    Front view of wire harness connector
    (to Airbag Sensor Assembly)
    *b
    Front view of wire harness connector
    (to Engine Room Main Wire)

    HINT:
    The service wire has already been inserted into connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    AF1-1 (+SL) - AF1-2 (-SL)
    Always
    Below 1 Ω



NG
REPLACE INSTRUMENT PANEL WIRE
OK

REPLACE ENGINE ROOM MAIN WIRE 

8.CHECK INSTRUMENT PANEL WIRE (SHORT)


    C251211E01
  1. Disconnect the instrument panel wire connector from the engine room main wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    AF1-1 (+SL) - AF1-2 (-SL)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Front Airbag Sensor
    *2
    Airbag Sensor Assembly
    *3
    Engine Room Main Wire
    *4
    Instrument Panel Wire
    *5
    Connector C
    *a
    Front view of wire harness connector
    (to Engine Room Main Wire)



NG
REPLACE INSTRUMENT PANEL WIRE
OK

REPLACE ENGINE ROOM MAIN WIRE 

9.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)


    C251211E01
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Disconnect the instrument panel wire connector from the engine room main wire.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    AF1-1 (+SL) - Body ground
    Ignition switch ON
    Below 1 V
    AF1-2 (-SL) - Body ground
    Ignition switch ON
    Below 1 V

    Text in Illustration 
    *1
    Front Airbag Sensor
    *2
    Airbag Sensor Assembly
    *3
    Engine Room Main Wire
    *4
    Instrument Panel Wire
    *5
    Connector C
    *a
    Front view of wire harness connector
    (to Engine Room Main Wire)



NG
REPLACE INSTRUMENT PANEL WIRE
OK

REPLACE ENGINE ROOM MAIN WIRE 

10.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)


    C251211E01
  1. Disconnect the instrument panel wire connector from the engine room main wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    AF1-1 (+SL) - Body ground
    Always
    1 MΩ or higher
    AF1-2 (-SL) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Front Airbag Sensor
    *2
    Airbag Sensor Assembly
    *3
    Engine Room Main Wire
    *4
    Instrument Panel Wire
    *5
    Connector C
    *a
    Front view of wire harness connector
    (to Engine Room Main Wire)



NG
REPLACE INSTRUMENT PANEL WIRE
OK

REPLACE ENGINE ROOM MAIN WIRE