Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > TERMINALS OF ECU

for Preparation Click here



POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY


  1. for LHD


    B291658E01


    1. Disconnect the H1 power window regulator master switch assembly connector.

    2. Measure the voltage and resistance according to the value(s) in the table below.

      w/ Rear Power Window 
      Terminal No. (Symbol)
      Wiring Color
      Terminal Description
      Condition
      Specified Condition
      H1-6 (B) - H1-1 (GND)
      GR - W-B
      Power supply
      Ignition switch ON
      11 to 14 V
      H1-1 (GND) - Body ground
      W-B - Body ground
      Ground
      Always
      Below 1 Ω

      w/o Rear Power Window 
      Terminal No. (Symbol)
      Wiring Color
      Terminal Description
      Condition
      Specified Condition
      H1-15 (B) - H1-7 (GND)
      GR - W-B
      Power supply
      Ignition switch ON
      11 to 14 V
      H1-7 (GND) - Body ground
      W-B - Body ground
      Ground
      Always
      Below 1 Ω
      If the result is not as specified, there may be a malfunction in the wire harness.

    3. Reconnect the power window regulator master switch assembly connector.

    4. Measure the voltage according to the value(s) in the table below.

      w/ Rear Power Window 
      Terminal No. (Symbol)
      Wiring Color
      Terminal Description
      Condition
      Specified Condition
      H1-8 (UP) - H1-1 (GND)
      R - W-B
      Power window motor UP operation
      Ignition switch ON, driver door power window switch OFF → UP (Manual operation)
      11 to 14 V → Below 1 V
      H1-5 (DOWN) - H1-1 (GND)
      G - W-B
      Power window motor DOWN operation
      Ignition switch ON, driver door power window switch OFF → DOWN (Manual operation)
      11 to 14 V → Below 1 V
      H1-4 (AUTO) - H1-1 (GND)
      R - W-B
      Power window motor AUTO operation
      Ignition switch ON, driver side door glass fully opened → driver side power window AUTO UP operation → driver side door glass fully closed
      11 to 14 V → Below 1 V → 11 to 14 V
      Ignition switch ON, driver side door glass fully closed → driver side power window AUTO DOWN operation → driver side door glass fully opened
      11 to 14 V → Below 1 V → 11 to 14 V
      H1-3 (LED) - H1-1 (GND)
      W - W-B
      LED illumination signal
      Ignition switch ON
      11 to 14 V
      Approximately 45 seconds after ignition switch turned off
      Below 1 V

      w/o Rear Power Window 
      Terminal No. (Symbol)
      Wiring Color
      Terminal Description
      Condition
      Specified Condition
      H1-18 (UP) - H1-7 (GND)
      R - W-B
      Power window motor UP operation
      Ignition switch ON, driver door power window switch OFF → UP (Manual operation)
      11 to 14 V → Below 1 V
      H1-10 (DOWN) - H1-7 (GND)
      G - W-B
      Power window motor DOWN operation
      Ignition switch ON, driver door power window switch OFF → DOWN (Manual operation)
      11 to 14 V → Below 1 V
      H1-1 (AUTO) - H1-7 (GND)
      R - W-B
      Power window motor AUTO operation
      Ignition switch ON, driver side door glass fully opened → driver side power window AUTO UP operation → driver side door glass fully closed
      11 to 14 V → Below 1 V → 11 to 14 V
      Ignition switch ON, driver side door glass fully closed → driver side power window AUTO DOWN operation → driver side door glass fully opened
      11 to 14 V → Below 1 V → 11 to 14 V
      H1-6 (LED) - H1-7 (GND)
      W - W-B
      LED illumination signal
      Ignition switch ON
      11 to 14 V
      Approximately 45 seconds after ignition switch turned off
      Below 1 V
      If the result is not as specified, the power window regulator master switch assembly may have a malfunction.



  2. for RHD


    B291658E02


    1. Disconnect the G1 power window regulator master switch assembly connector.

    2. Measure the voltage and resistance according to the value(s) in the table below.

      w/ Rear Power Window 
      Terminal No. (Symbol)
      Wiring Color
      Terminal Description
      Condition
      Specified Condition
      G1-6 (B) - G1-9 (GND)
      GR - W-B
      Power supply
      Ignition switch ON
      11 to 14 V
      G1-9 (GND) - Body ground
      W-B - Body ground
      Ground
      Always
      Below 1 Ω

      w/o Rear Power Window 
      Terminal No. (Symbol)
      Wiring Color
      Terminal Description
      Condition
      Specified Condition
      G1-15 (B) - G1-7 (GND)
      GR - W-B
      Power supply
      Ignition switch ON
      11 to 14 V
      G1-7 (GND) - Body ground
      W-B - Body ground
      Ground
      Always
      Below 1 Ω
      If the result is not as specified, there may be a malfunction in the wire harness.

    3. Reconnect the power window regulator master switch assembly connector.

    4. Measure the voltage according to the value(s) in the table below.

      w/ Rear Power Window 
      Terminal No. (Symbol)
      Wiring Color
      Terminal Description
      Condition
      Specified Condition
      G1-1 (UP) - G1-9 (GND)
      R - W-B
      Power window motor UP operation
      Ignition switch ON, driver door power window switch OFF → UP (Manual operation)
      11 to 14 V → Below 1 V
      G1-5 (DOWN) - G1-9 (GND)
      G - W-B
      Power window motor DOWN operation
      Ignition switch ON, driver door power window switch OFF → DOWN (Manual operation)
      11 to 14 V → Below 1 V
      G1-4 (AUTO) - G1-9 (GND)
      R - W-B
      Power window motor AUTO operation
      Ignition switch ON, driver side door glass fully opened → driver side power window AUTO UP operation → driver side door glass fully closed
      11 to 14 V → Below 1 V → 11 to 14 V
      Ignition switch ON, driver side door glass fully closed → driver side power window AUTO DOWN operation → driver side door glass fully opened
      11 to 14 V → Below 1 V → 11 to 14 V
      G1-3 (LED) - G1-9 (GND)
      W - W-B
      LED illumination signal
      Ignition switch ON
      11 to 14 V
      Approximately 45 seconds after ignition switch turned off
      Below 1 V

      w/o Rear Power Window 
      Terminal No. (Symbol)
      Wiring Color
      Terminal Description
      Condition
      Specified Condition
      G1-9 (UP) - G1-7 (GND)
      R - W-B
      Power window motor UP operation
      Ignition switch ON, driver door power window switch OFF → UP (Manual operation)
      11 to 14 V → Below 1 V
      G1-6 (DOWN) - G1-7 (GND)
      G - W-B
      Power window motor DOWN operation
      Ignition switch ON, driver door power window switch OFF → DOWN (Manual operation)
      11 to 14 V → Below 1 V
      G1-18 (AUTO) - G1-7 (GND)
      R - W-B
      Power window motor AUTO operation
      Ignition switch ON, driver side door glass fully opened → driver side power window AUTO UP operation → driver side door glass fully closed
      11 to 14 V → Below 1 V → 11 to 14 V
      Ignition switch ON, driver side door glass fully closed → driver side power window AUTO DOWN operation → driver side door glass fully opened
      11 to 14 V → Below 1 V → 11 to 14 V
      G1-16 (LED) - G1-7 (GND)
      W - W-B
      LED illumination signal
      Ignition switch ON
      11 to 14 V
      Approximately 45 seconds after ignition switch turned off
      Below 1 V
      If the result is not as specified, the power window regulator master switch assembly may have a malfunction.


CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY (FRONT PASSENGER SIDE)


  1. for LHD


    B291659E01


    1. Disconnect the G2 power window regulator switch assembly (front passenger side) connector.

    2. Measure the voltage according to the value(s) in the table below.

      Terminal No. (Symbol)
      Wiring Color
      Terminal Description
      Condition
      Specified Condition
      G2-3 (B) - Body ground
      L - Body ground
      Power supply
      Ignition switch ON
      11 to 14 V
      G2-5 (SU) - Body ground
      W - Body ground
      Ground
      Always
      Below 1 Ω
      G2-2 (SD) - Body ground
      P - Body ground
      Ground
      Always
      Below 1 Ω
      If the result is not as specified, there may be a malfunction in the wire harness.

    3. Reconnect the G2 power window regulator switch assembly (front passenger side) connector.

    4. Measure the voltage according to the value(s) in the table below.

      Terminal No. (Symbol)
      Wiring Color
      Terminal Description
      Condition
      Specified Condition
      G2-4 (U) - Body ground
      LA-R - Body ground
      Power window motor UP operation
      Front passenger side power window switch OFF → UP
      Below 1 V → 11 to 14 V
      G2-1 (D) - Body ground
      LA-G - Body ground
      Power window motor DOWN operation
      Front passenger side power window switch OFF → DOWN
      Below 1 V → 11 to 14 V
      If the result is not as specified, the power window regulator switch assembly (front passenger side) may have a malfunction.



  2. for RHD


    B291659E02


    1. Disconnect the H2 power window regulator switch assembly (front passenger side) connector.

    2. Measure the voltage according to the value(s) in the table below.

      Terminal No. (Symbol)
      Wiring Color
      Terminal Description
      Condition
      Specified Condition
      H2-3 (B) - Body ground
      L - Body ground
      Power supply
      Ignition switch ON
      11 to 14 V
      H2-5 (SU) - Body ground
      W - Body ground
      Ground
      Always
      Below 1 Ω
      H2-2 (SD) - Body ground
      P - Body ground
      Ground
      Always
      Below 1 Ω
      If the result is not as specified, there may be a malfunction in the wire harness.

    3. Reconnect the H2 power window regulator switch assembly (front passenger side) connector.

    4. Measure the voltage according to the value(s) in the table below.

      Terminal No. (Symbol)
      Wiring Color
      Terminal Description
      Condition
      Specified Condition
      H2-4 (U) - Body ground
      LA-R - Body ground
      Power window motor UP operation
      Front passenger side power window switch OFF → UP
      Below 1 V → 11 to 14 V
      H2-1 (D) - Body ground
      LA-G - Body ground
      Power window motor DOWN operation
      Front passenger side power window switch OFF → DOWN
      Below 1 V → 11 to 14 V
      If the result is not as specified, the power window regulator switch assembly (front passenger side) may have a malfunction.


CHECK REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH

B291659E03

  1. Disconnect the J1 rear power window regulator switch assembly LH connector.

  2. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    J1-3 (B) - Body ground
    LA-SB - Body ground
    Power supply
    Ignition switch ON
    11 to 14 V
    J1-5 (SU) - Body ground
    LA-R - Body ground
    Ground
    Always
    Below 1 Ω
    J1-2 (SD) - Body ground
    LA-G - Body ground
    Ground
    Always
    Below 1 Ω

  3. Reconnect the J1 rear power window regulator switch assembly LH connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    J1-4 (U) - Body ground
    LA-Y - Body ground
    Power window motor UP operation
    Front passenger side power window switch OFF → UP
    Below 1 V → 11 to 14 V
    J1-1 (D) - Body ground
    LA-B - Body ground
    Power window motor DOWN operation
    Front passenger side power window switch OFF → DOWN
    Below 1 V → 11 to 14 V
    If the result is not as specified, the rear power window regulator switch assembly LH may have a malfunction.


CHECK REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH

B291659E04

  1. Disconnect the I1 rear power window regulator switch assembly RH connector.

  2. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I1-3 (B) - Body ground
    LA-SB - Body ground
    Power supply
    Ignition switch ON
    11 to 14 V
    I1-5 (SU) - Body ground
    LA-R - Body ground
    Ground
    Always
    Below 1 Ω
    I1-2 (SD) - Body ground
    LA-G - Body ground
    Ground
    Always
    Below 1 Ω

  3. Reconnect the I1 rear power window regulator switch assembly RH connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I1-4 (U) - Body ground
    LA-Y - Body ground
    Power window motor UP operation
    Front passenger side power window switch OFF → UP
    Below 1 V → 11 to 14 V
    I1-1 (D) - Body ground
    LA-B - Body ground
    Power window motor DOWN operation
    Front passenger side power window switch OFF → DOWN
    Below 1 V → 11 to 14 V
    If the result is not as specified, the rear power window regulator switch assembly RH may have a malfunction.


CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY LH OR RH (DRIVER SIDE)


  1. for LHD


    B291660E01


    1. Disconnect the H3 power window regulator motor assembly LH connector.

    2. Measure the voltage and resistance according to the value(s) in the table below.

      Terminal No. (Symbol)
      Wiring Color
      Terminal Description
      Condition
      Specified Condition
      H3-2 (B) - H3-1 (GND)
      G - W-B
      Power supply
      Always
      11 to 14 V
      H3-1 (GND) - Body ground
      W-B - Body ground
      Ground
      Always
      Below 1 Ω
      If the result is not as specified, there may be a malfunction in the wire harness.

    3. Reconnect the power window regulator motor assembly LH connector.

    4. Measure the voltage according to the value(s) in the table below.

      Terminal No. (Symbol)
      Wiring Color
      Terminal Description
      Condition
      Specified Condition
      H3-10 (UP) - H3-1 (GND)
      R - W-B
      Power window motor UP operation
      Ignition switch ON, driver door power window switch OFF → UP (Manual operation)
      11 to 14 V → Below 1 V
      H3-7 (DOWN) - H3-1 (GND)
      G - W-B
      Power window motor DOWN operation
      Ignition switch ON, driver door power window switch OFF → DOWN (Manual operation)
      11 to 14 V → Below 1 V
      H3-4 (AUTO) - H3-1 (GND)
      R - W-B
      Power window motor AUTO operation
      Ignition switch ON, driver side door glass fully opened → driver side power window AUTO UP operation → driver side door glass fully closed
      11 to 14 V → Below 1 V → 11 to 14 V
      Ignition switch ON, driver side door glass fully closed → driver side power window AUTO DOWN operation → driver side door glass fully opened
      11 to 14 V → Below 1 V → 11 to 14 V
      H3-5 (LED) - H3-1 (GND)
      W - W-B
      LED illumination signal
      Ignition switch ON
      11 to 14 V
      Approximately 45 seconds after ignition switch turned off
      Below 1 V
      If the result is not as specified, the power window regulator motor assembly LH may have a malfunction.



  2. for RHD


    B291660E02


    1. Disconnect the G3 power window regulator motor assembly RH connector.

    2. Measure the voltage and resistance according to the value(s) in the table below.

      Terminal No. (Symbol)
      Wiring Color
      Terminal Description
      Condition
      Specified Condition
      G3-2 (B) - G3-1 (GND)
      G - W-B
      Power supply
      Always
      11 to 14 V
      G3-1 (GND) - Body ground
      W-B - Body ground
      Ground
      Always
      Below 1 Ω
      If the result is not as specified, there may be a malfunction in the wire harness.

    3. Reconnect the power window regulator motor assembly RH connector.

    4. Measure the voltage according to the value(s) in the table below.

      Terminal No. (Symbol)
      Wiring Color
      Terminal Description
      Condition
      Specified Condition
      G3-10 (UP) - G3-1 (GND)
      R - W-B
      Power window motor UP operation
      Ignition switch ON, driver door power window switch OFF → UP (Manual operation)
      11 to 14 V → Below 1 V
      G3-7 (DOWN) - G3-1 (GND)
      G - W-B
      Power window motor DOWN operation
      Ignition switch ON, driver door power window switch OFF → DOWN (Manual operation)
      11 to 14 V → Below 1 V
      G3-4 (AUTO) - G3-1 (GND)
      R - W-B
      Power window motor AUTO operation
      Ignition switch ON, driver side door glass fully opened → driver side power window AUTO UP operation → driver side door glass fully closed
      11 to 14 V → Below 1 V → 11 to 14 V
      Ignition switch ON, driver side door glass fully closed → driver side power window AUTO DOWN operation → driver side door glass fully opened
      11 to 14 V → Below 1 V → 11 to 14 V
      G3-5 (LED) - G3-1 (GND)
      W - W-B
      LED illumination signal
      Ignition switch ON
      11 to 14 V
      Approximately 45 seconds after ignition switch turned off
      Below 1 V
      If the result is not as specified, the power window regulator motor assembly RH may have a malfunction.


CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU

E233158E01


Text in Illustration 
*A
for LHD
*B
for RHD
*1
Instrument Panel Junction Block Assembly
*2
Main Body ECU
  1. Remove the main body ECU.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    MB-11 (GND1) - Body ground
    -
    Ground
    Always
    Below 1 Ω
    MB-29 (ACC) - Body ground
    -
    Ignition power supply (ACC signal)
    Ignition switch ACC
    11 to 14 V
    MB-30 (BECU) - Body ground
    -
    Battery power supply
    Always
    11 to 14 V
    MB-32 (IG) - Body ground
    -
    Ignition power supply (IG signal)
    Ignition switch ON
    11 to 14 V
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reinstall the main body ECU.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F76-2 (KOFF) - Body ground
    L - Body ground
    Power window relay operation signal
    Ignition switch ON
    11 to 14 V
    Approximately 45 seconds after ignition switch turned off
    Below 1 V
    F76-19 (FRCY) - Body ground
    Y - Body ground
    Front door courtesy light switch RH signal
    Front door RH opened
    Below 1 V
    Front door RH closed
    Pulse generation
    3D-36 (FLCY) - Body ground
    L - Body ground
    Front door courtesy light switch LH signal
    Front door LH opened
    Below 1 V
    Front door LH closed
    Pulse generation
    3B-12 (LIN2) - Body ground
    W - Body ground
    LIN communication signal
    Ignition switch ON
    Pulse generation

    HINT:
    If the result is not as specified, the main body ECU or instrument panel junction block assembly may have a malfunction.