Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › NAME PLATE

NAME PLATE > INSTALLATION

for Preparation Click here



1. INSTALL NO. 2 LUGGAGE COMPARTMENT DOOR NAME PLATE
  1. Clean the attachment surface.

    1. Using an infrared light, heat the double-sided tape remaining on the back door panel.
      Heating Temperature 
      Item
      Temperature
      Vehicle Body
      40 to 60°C (104 to 140°F)

      CAUTION:
      Do not burn yourself on the hot body panel or with the infrared light.

      NOTICE:
      Do not heat the vehicle body excessively.

    2. Using a piece of cloth, rub the double-sided tape off the back door panel while it is hot from the infrared light.

      NOTICE:
      Installing the No. 2 luggage compartment door name plate while any double-sided tape remains on the back door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.

    3. Using a non-residue solvent, clean the attachment surface.



  1. Install a new No. 2 luggage compartment door name plate as shown in the illustration.


    B283006E02

    Installation Position:
    Mark
    Measurement (along surface)
    *1
    223.8 mm (8.81 in.)
    *2
    211.9 mm (8.34 in.)
    *3
    167.1 mm (6.58 in.)

    NOTICE:
    Install the No. 2 luggage compartment door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the back door panel and the No. 2 luggage compartment door name plate to 20 to 30°C (68 to 86°F) and install the No. 2 luggage compartment door name plate.



2. INSTALL NO. 6 BACK DOOR NAME PLATE
  1. Clean the attachment surface.

    1. Using an infrared light, heat the double-sided tape remaining on the back door panel.
      Heating Temperature 
      Item
      Temperature
      Vehicle Body
      40 to 60°C (104 to 140°F)

      CAUTION:
      Do not burn yourself on the hot body panel or with the infrared light.

      NOTICE:
      Do not heat the vehicle body excessively.

    2. Using a piece of cloth, rub the double-sided tape off the back door panel while it is hot from the infrared light.

      NOTICE:
      Installing the No. 6 back door name plate while any double-sided tape remains on the back door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.

    3. Using a non-residue solvent, clean the attachment surface.



  1. Install a new No. 6 back door name plate as shown in the illustration.


    B283005E02

    Installation Position:
    Mark
    Measurement (along surface)
    *1
    215.8 mm (8.50 in.)
    *2
    220.0 mm (8.66 in.)
    *3
    51.5 mm (2.03 in.)

    NOTICE:
    Install the No. 6 back door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the back door panel and the No. 6 back door name plate to 20 to 30°C (68 to 86°F) and install the No. 6 back door name plate.



3. INSTALL SYMBOL EMBLEM
  1. Clean the attachment surface.

    1. Using an infrared light, heat the double-sided tape remaining on the back door panel.
      Heating Temperature 
      Item
      Temperature
      Vehicle Body
      40 to 60°C (104 to 140°F)

      CAUTION:
      Do not burn yourself on the hot body panel or with the infrared light.

      NOTICE:
      Do not heat the vehicle body excessively.

    2. Using a piece of cloth, rub the remaining double-sided tape off the back door panel while it is hot from the infrared light.

      NOTICE:
      Installing the symbol emblem with any double-sided tape remaining on the back door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.

    3. Using a non-residue solvent, clean the attachment surface.



    B283004E01
  1. Insert the 2 pins into the back door panel and install a new symbol emblem.
    Text in Illustration 
    *1
    Location Pin

    NOTICE:
    Install the symbol emblem in an environment where the ambient temperature is over 20 °C (68°F). If it is below 20°C (68°F), using an infrared light, heat the back door panel and the symbol emblem to 20 to 30°C (68 to 86°F) and install the symbol emblem.