Home › Drivetrain ยท U340E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE UNIT

AUTOMATIC TRANSAXLE UNIT > DISASSEMBLY

for Preparation Click here



1. REMOVE TRANSMISSION CONTROL SHAFT LEVER


    C117101
  1. Remove the nut, washer and the transmission control shaft lever.



2. REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY


    C117104
  1. Using a screwdriver, pry out the lock plate and remove the nut, lock plate and washer.



    C117106
  1. Remove the 2 bolts and pull out the park/neutral position switch assembly.



3. REMOVE TRANSMISSION REVOLUTION SENSOR


C067751E02
  1. Remove the bolt and the transmission revolution sensor.

  1. Remove the O-ring from the transmission revolution sensor.



4. REMOVE OIL COOLER TUBE UNION


D025286E02
  1. Remove the 2 oil cooler tube unions from the transaxle case.

  1. Remove the 2 O-rings from the 2 oil cooler tube unions.



5. REMOVE NO. 1 TRANSAXLE CASE PLUG


C067754E01
  1. Remove the 4 No. 1 transaxle case plugs from the transaxle housing and the transaxle case.



    C067755E01
  1. Remove the No. 1 transaxle case plug from the transaxle case.

  1. Remove the 5 O-rings from each No. 1 transaxle case plugs.



6. REMOVE TRANSMISSION BREATHER HOSE SUB-ASSEMBLY


C067752E01
  1. Remove the transmission breather hose sub-assembly from the breather plug.



7. REMOVE BREATHER PLUG
  1. Remove the breather plug from the transaxle case.

  1. Remove the O-ring from the breather plug.



8. FIX AUTOMATIC TRANSAXLE ASSEMBLY


    C163764E02
  1. Secure the transaxle on wooden blocks.
    Text in Illustration 
    *1
    Wooden Block



9. REMOVE AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY
  1. Remove the drain plug and gasket from the automatic transaxle oil pan sub-assembly.



    C062684E10
  1. Remove the 19 bolts, automatic transaxle oil pan sub-assembly and the automatic transaxle oil pan gasket.



    C093943E16
  1. Remove the 2 oil cleaner magnets from the automatic transaxle oil pan sub-assembly.

  1. Examine the particles in the automatic transaxle oil pan gasket.

    1. Collect any steel chips with the removed magnets.
      Carefully look at the foreign matter and particles in the automatic transaxle oil pan gasket and on the magnets to predict the type of wear which might be found in the transaxle.
      Steel (magnetic): bearing, gear and clutch plate wear
      Brass (non-magnetic): bearing wear



10. REMOVE VALVE BODY OIL STRAINER ASSEMBLY


C062685E02
  1. Remove the 3 bolts and the valve body oil strainer assembly.



    D005904E12
  1. Remove the oil strainer gasket from the valve body oil strainer assembly.



11. REMOVE TRANSMISSION VALVE BODY ASSEMBLY


    C093938E05
  1. Disconnect the 5 connectors from the transmission valve body assembly.

  1. Remove the bolt and the lock plate, and separate the transmission wire.



    C093939E37
  1. Remove the 2 bolts, manual detent spring cover and the manual detent spring.
    Text in Illustration 
    *1
    Manual Detent Spring
    *2
    Manual Detent Spring Cover



    C093940E10
  1. Remove the 13 bolts and the transmission valve body assembly from the transaxle case.



12. REMOVE TRANSMISSION WIRE


C062929E01
  1. Remove the bolt and the transmission wire from the transaxle case.



    C067760E01
  1. Remove the O-ring from the transmission wire.



13. REMOVE TRANSAXLE CASE 2ND BRAKE GASKET


C067757E01
  1. Remove the transaxle case 2nd brake gasket from the transaxle case.



14. REMOVE TRANSAXLE CASE GASKET


C067758E01
  1. Remove the transaxle case gasket from the transaxle case.



15. REMOVE BRAKE DRUM GASKET


C067759E02
  1. Remove the brake drum gasket from the transaxle case.



16. REMOVE CHECK BALL BODY


C067767E01
  1. Remove the check ball body and the check ball body compression spring from the transaxle case.



17. REMOVE B-2 ACCUMULATOR PISTON


C067761E01
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole and remove the B-2 accumulator piston and the B-2 accumulator piston compression spring.

    NOTICE:
    1. Blowing the air may cause the piston to jump out. When removing the piston, hold it by hand using a piece of cloth.
    2. Do not splash ATF with the compressed air.



    D025038E01
  1. Remove the 2 B-2 accumulator piston O-rings from the B-2 accumulator piston.



18. REMOVE C-3 ACCUMULATOR PISTON


C067762E01
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole and remove the C-3 accumulator piston and the C-3 accumulator piston compression spring.

    NOTICE:
    1. Blowing the air may cause the piston to jump out. When removing the piston, hold it with your hand using a piece of cloth.
    2. Do not splash ATF with the compressed air.



    D025039E01
  1. Remove the 2 C-3 accumulator piston O-rings from the C-3 accumulator piston.



19. REMOVE C-2 ACCUMULATOR PISTON


C067763E01
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole and remove the C-2 accumulator piston and the C-2 accumulator piston compression spring.

    NOTICE:
    1. Blowing the air may cause the piston to jump out. When removing the piston, hold it by hand using a piece of cloth.
    2. Do not splash ATF with the compressed air.



    D025040E01
  1. Remove the 2 C-2 accumulator piston O-rings from the C-2 accumulator piston.



20. REMOVE TRANSAXLE HOUSING


C161934E02
  1. Remove the 14 bolts.

  1. Tap around the circumference of the transaxle housing with a plastic hammer to remove the transaxle housing from the transaxle case.

    NOTICE:
    The differential gear assembly may be accidentally removed when the transaxle housing is removed.



21. INSPECT INPUT SHAFT END PLAY


C067772E02
  1. Measure the end play in the axial direction.

    End play:
    0.37 to 1.29 mm (0.0146 to 0.0508 in.)

    If the end play is not as specified, select and replace the thrust needle roller bearing.



22. REMOVE OIL PUMP ASSEMBLY


C067773E04
  1. Remove the 7 bolts and the oil pump assembly from the transaxle case.



23. REMOVE DIFFERENTIAL GEAR ASSEMBLY


C162529
  1. Remove the differential gear assembly from the transaxle case.



24. REMOVE OVERDRIVE BRAKE GASKET


C067783E01
  1. Using a screwdriver, remove the 2 overdrive brake gaskets from the transaxle case.



25. REMOVE INPUT SHAFT ASSEMBLY


C067775E01
  1. Remove the input shaft assembly from the transaxle case.



26. REMOVE STATOR SHAFT THRUST NEEDLE ROLLER BEARING


C067782E01
  1. Remove the stator shaft thrust needle roller bearing from the input shaft assembly.



27. REMOVE FRONT CLUTCH CLUTCH DISC


    C067851E01
  1. Using a screwdriver, remove the snap ring.

  1. Remove the forward clutch flange, 4 front clutch clutch discs and the 4 No. 1 clutch plates from the input shaft sub-assembly.



28. REMOVE FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY


    D008368E01
  1. Using SST on the No. 1 clutch balancer, compress the forward clutch return spring sub-assembly with a press.

    SST
    09320-89010  

    NOTICE:
    Do not compress the return spring excessively.

  1. Using a snap ring expander, remove the snap ring.



    D008369E01
  1. Remove the No. 1 clutch balancer and the forward clutch return spring sub-assembly.



29. REMOVE FORWARD CLUTCH PISTON


    C067856E01
  1. Place the input shaft onto the oil pump.

  1. Holding the forward clutch piston by hand, apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil pump to remove the forward clutch piston.

    HINT:
    When the piston cannot be removed due to being slanted, either blow the air again with the protruding side pushed or remove the piston using needle-nose pliers with their tips wrapped in protective tape.



30. REMOVE FORWARD CLUTCH PISTON O-RING


    C067857E02
  1. Using a screwdriver, remove the forward clutch piston O-ring from the forward clutch piston.



31. REMOVE INPUT SHAFT OIL SEAL RING


    C067858E01
  1. Using a screwdriver, remove the input shaft oil seal ring from the input shaft sub-assembly.



32. REMOVE FORWARD CLUTCH HUB THRUST NEEDLE ROLLER BEARING


C067776E01
  1. Remove the forward clutch hub thrust needle roller bearing from the forward clutch hub sub-assembly.



33. INSPECT INTERMEDIATE SHAFT ASSEMBLY


D025043E01
  1. Using a dial indicator, measure the clearance of the intermediate shaft assembly.

    Standard clearance:
    0.204 to 0.966 mm (0.00803 to 0.03803 in.)

    If the clearance is outside the specification, replace the rear clutch drum thrust needle roller bearing.



34. REMOVE FORWARD CLUTCH HUB SUB-ASSEMBLY


C067777E01
  1. Remove the forward clutch hub sub-assembly from the transaxle case.



35. REMOVE REAR TRANSAXLE COVER ASSEMBLY


C067778E04
  1. Remove the 11 bolts.

  1. Tap around the circumference of the rear transaxle cover with a plastic hammer to remove the rear transaxle cover assembly from the transaxle case.



36. REMOVE REAR TRANSAXLE COVER PLUG


    C067881E04
  1. Remove the 4 rear transaxle cover plugs from the rear transaxle cover.

  1. Using a screwdriver, remove the 4 O-rings from the 4 rear transaxle cover plugs.



37. REMOVE OVERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY


    C248586E01
  1. Using SST, a press and a screwdriver, remove the snap ring.

    SST
    09387-00070  

    NOTICE:
    Stop the press when the overdrive brake piston is lowered to 1 to 2 mm (0.0394 to 0.0787 in.) from the snap ring groove, to prevent the overdrive brake piston from being deformed.



    D008358E01
  1. Remove the overdrive brake return spring sub-assembly from the rear transaxle cover.



38. REMOVE 2ND COAST AND OVERDRIVE BRAKE PISTON


    C067883E01
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the rear transaxle cover to remove the 2nd coast and overdrive brake piston.

    NOTICE:
    1. Blowing the air may cause the piston to jump out. When removing the piston, hold it by hand using a piece of cloth.
    2. Do not splash ATF with the compressed air.



39. REMOVE 2ND COAST AND OVERDRIVE O-RING


    C067884E01
  1. Using a screwdriver, remove the 2 2nd coast and overdrive O-rings from the 2nd coast and overdrive brake piston.



40. REMOVE CLUTCH DRUM OIL SEAL RING


    C067885E03
  1. Remove the 3 clutch drum oil seal rings from the rear transaxle cover.



41. REMOVE REAR TRANSAXLE COVER NEEDLE ROLLER BEARING


    C082194E07
  1. Using SST, remove the rear transaxle cover needle roller bearing from the rear transaxle cover.
    Text in Illustration 
    *a
    Hold
    *b
    Turn

    SST
    09387-00041   (09387-01021)



42. REMOVE TRANSAXLE CASE GASKET


C067779E03
  1. Remove the 4 transaxle case gaskets from the transaxle case.



43. REMOVE REAR CLUTCH DRUM THRUST NEEDLE ROLLER BEARING


C067780E01
  1. Using a magnet hand, remove the rear clutch drum thrust needle roller bearing.



44. REMOVE INTERMEDIATE SHAFT ASSEMBLY


C067781E01
  1. Remove the intermediate shaft assembly from the transaxle case.



45. REMOVE REVERSE CLUTCH DISC


    C067867E01
  1. Using a screwdriver, remove the snap ring from the intermediate shaft.

  1. Remove the reverse clutch flange, 2 reverse clutch discs and the 2 No. 3 clutch plates from the intermediate shaft.



46. REMOVE DIRECT CLUTCH DISC


    C067869E01
  1. Using a screwdriver, remove the snap ring from the intermediate shaft.

  1. Remove the direct clutch flange, 3 direct clutch disc and the 3 rear clutch flanges from the intermediate shaft.



47. REMOVE DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY


    C067871E03
  1. Using SST, a press and snap ring expander, remove the snap ring from the direct clutch piston sub-assembly.

    SST
    09387-00020  

  1. Remove the direct clutch return spring sub-assembly from the intermediate shaft.



48. REMOVE DIRECT CLUTCH PISTON SUB-ASSEMBLY


    C067873E01
  1. Install the intermediate shaft onto the rear transaxle cover.

  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole shown in the illustration and remove the direct clutch piston sub-assembly from the intermediate shaft.

    NOTICE:
    1. Blowing the air may cause the piston to jump out. When removing the piston, hold it by hand using a piece of cloth.
    2. Do not splash ATF with the compressed air.



49. REMOVE DIRECT CLUTCH DRUM SUB-ASSEMBLY


    D025110E01
  1. Install the intermediate shaft onto the rear transaxle cover.

  1. Put a matchmark on the direct clutch drum sub-assembly in the same position as the cutout of the intermediate shaft.

  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole shown in the illustration and remove the direct clutch drum sub-assembly from the intermediate shaft.

    NOTICE:
    1. Blowing the air may cause the drum to jump out. When removing the drum, hold it by hand using a piece of cloth.
    2. Do not splash ATF with the compressed air.



50. REMOVE DIRECT CLUTCH PISTON O-RING


    C067875E03
  1. Using a screwdriver, remove the 2 direct clutch piston O-rings from the direct clutch piston sub-assembly.



51. REMOVE DIRECT CLUTCH DRUM O-RING


    C067876E02
  1. Using a screwdriver, remove the direct clutch drum O-ring from the direct clutch drum sub-assembly.



52. REMOVE 2ND COAST AND OVERDRIVE BRAKE DISC


C067785E01
  1. Remove the 2nd coast and overdrive brake flange, 2 2nd coast and overdrive brake discs and the 2 No. 2 2nd coast and overdrive brake flanges from the transaxle case.



53. REMOVE THRUST NEEDLE ROLLER BEARING


C067784E01
  1. Using a magnet hand, remove the C-2 hub thrust bearing race, thrust needle roller bearing and the No. 3 thrust bearing race from the direct clutch hub.



54. REMOVE DIRECT CLUTCH HUB


C068196E01
  1. Remove the direct clutch hub from the transaxle case.



55. REMOVE REAR NO. 2 PLANETARY SUN GEAR THRUST NEEDLE ROLLER BEARING


C067786E01
  1. Using a magnet hand, remove the rear No. 2 planetary sun gear thrust needle roller bearing from the rear planetary sun gear assembly.



56. REMOVE REAR PLANETARY SUN GEAR ASSEMBLY


C067973E01
  1. Remove the rear planetary sun gear assembly from the transaxle case.



57. REMOVE REAR PLANETARY SUN GEAR THRUST NEEDLE ROLLER BEARING


C068161E02
  1. Remove the rear planetary sun gear thrust needle roller bearing and the No. 1 planetary carrier thrust washer from the rear planetary sun gear assembly.



58. INSPECT 1-WAY CLUTCH ASSEMBLY


D025044E11
  1. Hold the rear planetary sun gear and turn the 1-way clutch assembly.
    Text in Illustration 
    *a
    Free
    *b
    Lock
    *c
    Hold

  1. Make sure that 1-way clutch assembly turns freely counterclockwise and locks when turned clockwise.
    If the 1-way clutch assembly does not operate normally, replace it.



59. REMOVE 1-WAY CLUTCH ASSEMBLY


C068163E01
  1. Remove the 1-way clutch assembly and the No. 2 planetary carrier thrust washer from the rear planetary sun gear assembly.



60. REMOVE 2ND COAST AND OVERDRIVE BRAKE FLANGE HOLE SNAP RING


C067971E01
  1. Using a screwdriver, remove the 2nd coast and overdrive brake flange hole snap ring from the transaxle case.



61. REMOVE 2ND BRAKE BRAKE DISC


C067969E01
  1. Using a screwdriver, remove the snap ring from the transaxle case.

  1. Remove the 2nd brake brake flange, 3 2nd brake brake discs and the 3 No. 1 2nd brake brake flanges from the transaxle case.



62. REMOVE 2ND BRAKE PISTON SLEEVE


C067970E01
  1. Remove the 2nd brake piston sleeve from the transaxle case.



63. INSPECT NO. 2 1-WAY CLUTCH


D025045E08
  1. Hold the rear planetary gear assembly and turn the No. 2 1-way clutch.
    Text in Illustration 
    V100135
    Lock
    V100136
    Free

  1. Make sure that the No. 2 1-way clutch turns freely counterclockwise and locks when turned clockwise.
    If the No. 2 1-way clutch does not operate normally, replace it.



64. REMOVE REAR PLANETARY GEAR ASSEMBLY


C067967E01
  1. Using a screwdriver, remove the snap ring from the transaxle case.

  1. Remove the rear planetary gear assembly from the transaxle case.



65. REMOVE REAR PLANETARY GEAR THRUST NEEDLE ROLLER BEARING


C068159E01
  1. Remove the rear planetary gear thrust needle roller bearing, No. 2 thrust bearing race and the thrust bearing race from the rear planetary gear assembly.



66. REMOVE NO. 2 1-WAY CLUTCH


C067966E01
  1. Remove the No. 2 1-way clutch, 2nd brake piston assembly from the rear planetary gear assembly.



67. REMOVE OUTER RACE RETAINER


C067965E01
  1. Remove the outer race retainer from the No. 2 1-way clutch.



68. REMOVE 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY


    D003796E04
  1. Using SST and a press, remove the snap ring.

    SST
    09387-00060  



    C067862E01
  1. Remove the 2nd brake piston return spring sub-assembly from the 2nd brake cylinder.



69. REMOVE 2ND BRAKE PISTON


    C067863E01
  1. Hold the 2nd brake piston and apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the 2nd brake cylinder to remove the 2nd brake piston.



70. REMOVE 2ND BRAKE CYLINDER O-RING


    C067864E02
  1. Using a screwdriver, remove the 2 2nd brake cylinder O-rings from the 2nd brake cylinder.



71. REMOVE FRONT PLANETARY SUN GEAR


C068157E01
  1. Remove the front planetary sun gear and the front planetary gear thrust needle roller bearing from the transaxle case.



72. REMOVE 1ST AND REVERSE BRAKE DISC


C067963E01
  1. Using a screwdriver, remove the snap ring from the transaxle case.

  1. Remove the 1st and reverse brake flange, 4 1st and reverse brake discs and the 4 1st and reverse brake plates from the transaxle case.



73. REMOVE COUNTER DRIVE GEAR NUT


C067960E01
  1. Fix the counter drive gear with the parking lock pawl.



    C067961E01
  1. Using SST and a hammer, release the counter drive gear lock nut washer.

    SST
    09930-00010  



    D025048E02
  1. Using SST, remove the counter drive gear nut and the counter drive gear lock nut washer.

    SST
    09387-00121  



74. REMOVE PLANETARY GEAR ASSEMBLY


D025047E01
  1. Using SST and a press, remove the planetary gear assembly from the transaxle case.

    SST
    09950-60010   (09951-00400, 09951-00320, 09952-06010)
    09950-70010   (09951-07100)



75. REMOVE COUNTER DRIVE GEAR


C068474E05
  1. Install the 2 bolts to the counter drive gear.

    Recommended service bolt:
    Diameter:
    10 mm
    Pitch:
    1.25 mm
    Length:
    40 to 80 mm (1.575 to 3.150 in.)

  1. Rotate the 2 bolts and remove the counter drive gear.



76. REMOVE 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY


D008332E02
  1. Using SST, a press and screwdriver, remove the snap ring from the transaxle case.

    SST
    09387-00070  

  1. Remove the 1st and reverse brake return spring sub-assembly from the transaxle case.



77. REMOVE NO. 2 1ST AND REVERSE BRAKE PISTON


C068211E01
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transaxle case to remove the 1st and reverse brake piston.

    NOTICE:
    1. Blowing the air may cause the piston to jump out. When removing the piston, hold it by hand using a piece of cloth.
    2. Do not splash ATF with the compressed air.



78. REMOVE NO. 2 1ST AND REVERSE BRAKE PISTON O-RING


C067962E01
  1. Remove the 2 No. 2 1st and reverse brake piston O-rings from the No. 2 1st and reverse brake piston.



79. REMOVE PARKING LOCK PAWL BRACKET


C067957E04
  1. Remove the 3 bolts, parking lock cam guide and the parking lock pawl bracket from the transaxle case.



80. REMOVE MANUAL VALVE LEVER SHAFT RETAINER SPRING


C067956E01
  1. Remove the manual valve lever shaft retainer spring from the manual valve lever shaft.



81. REMOVE MANUAL VALVE LEVER SUB-ASSEMBLY


C067954E01
  1. Using a screwdriver, release and remove the manual valve lever shaft spacer.



    C067950E01
  1. Using a pin punch 3 mm and hammer, drive out the manual valve lever shaft spring pin.

  1. Remove the manual valve lever shaft and manual valve lever sub-assembly.



82. REMOVE PARKING LOCK ROD SUB-ASSEMBLY


C067951E01
  1. Remove the parking lock rod sub-assembly from the manual valve lever sub-assembly.



83. REMOVE MANUAL VALVE LEVER SHAFT


C067952E01
  1. Remove the manual valve lever shaft from the transaxle case.



84. REMOVE PARKING LOCK PAWL


C067948E01
  1. Using a screwdriver, remove the parking lock pawl shaft from the transaxle case.

  1. Remove the parking lock pawl torsion spring and the parking lock pawl from the transaxle case.



85. REMOVE DIFFERENTIAL DRIVE PINION SUB-ASSEMBLY


C068164E01
  1. Remove the differential drive pinion sub-assembly and the drive pinion thrust bearing LH from the transaxle case.



86. REMOVE DIFFERENTIAL DRIVE PINION PLUG


C068188E01
  1. Using a brass bar and hammer, remove the differential drive pinion plug.



87. REMOVE BEARING LOCK PLATE


C067770E01
  1. Remove the bolt and the bearing lock plate.



88. REMOVE DIFFERENTIAL GEAR LUBE APPLY TUBE


C068187E01
  1. Remove the differential gear lube apply tube from the transaxle housing.



89. REMOVE FRONT DRIVE PINION FRONT TAPERED ROLLER BEARING


    C067771E11
  1. Using SST, remove the front drive pinion front tapered roller bearing from the transaxle housing.
    Text in Illustration 
    *a
    Hold
    *b
    Turn

    SST
    09308-10010  

  1. Remove the drive pinion thrust bearing RH from the transaxle housing.



90. REMOVE FRONT DRIVE PINION REAR TAPERED ROLLER BEARING


    C067946E06
  1. Using SST, remove the front drive pinion rear tapered roller bearing from the transaxle case.
    Text in Illustration 
    *1
    No. 1 Transaxle Case Plate
    *a
    Hold
    *b
    Turn

    SST
    09612-65014   (09612-01040)

  1. Remove the No. 1 transaxle case plate from the transaxle case.



91. REMOVE COUNTER DRIVE GEAR BEARING


D025049E05
  1. Remove the 2 counter drive gear bearing inner races and 2 angular balls from the transaxle case.

  1. Using SST, remove the counter drive gear bearing outer race from the transaxle case.

    SST
    09308-00010  



    D025050E05
  1. Using SST, remove the counter drive gear bearing outer race from the transaxle case.

    SST
    09308-00010  



92. REMOVE COUNTER DRIVE GEAR HOLE SNAP RING


C067955E01
  1. Using a screwdriver, remove the counter drive gear hole snap ring from the transaxle case.



93. REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL


C067953E01
  1. Using a screwdriver, remove the manual valve lever shaft oil seal from the transaxle case.



94. REMOVE FRONT TRANSAXLE CASE OIL SEAL


C067941E01
  1. Using SST and a hammer, remove the front transaxle case oil seal from the transaxle case.

    SST
    09950-60010   (09951-00530)
    09950-70010   (09951-07100)



95. REMOVE TRANSAXLE CASE OIL SEAL


C067942E01
  1. Using SST and a hammer, remove the transaxle case oil seal from the transaxle housing.

    SST
    09950-60010   (09951-00550)
    09950-70010   (09951-07100)