INPUT SHAFT > REASSEMBLY |
| 1. INSTALL NO. 2 TRANSMISSION HUB SLEEVE |
![]() |
Coat the No. 2 transmission hub sleeve with gear oil, and install it to the No. 2 transmission clutch hub.
Using a screwdriver, install the 3 synchromesh shifting key springs with the 3 synchromesh shifting keys onto the No. 2 transmission clutch hub.
| 2. INSTALL 3RD GEAR NEEDLE ROLLER BEARING |
![]() |
Coat the 3rd gear needle roller bearing with gear oil and install it onto the input shaft.
| 3. INSTALL 3RD GEAR |
![]() |
Coat the 3rd gear with gear oil and install it onto the input shaft.
| 4. INSTALL 3RD GEAR SYNCHRONIZER RING |
![]() |
Coat the 3rd gear synchronizer ring with gear oil and install it onto the 3rd gear.
| *a | Key Position |
| *b | for 3rd Gear |
| 5. INSTALL NO. 2 TRANSMISSION CLUTCH HUB |
![]() |
Using SST and a press, install the No. 2 transmission clutch hub onto the input shaft.
![]() |
Select a snap ring that will allow minimum axial play.
| Part No. | Mark | Thickness mm (in.) |
| 90520-27046 | 0 | 2.30 (0.0906) |
| 90520-27047 | 1 | 2.36 (0.0929) |
| 90520-27048 | 2 | 2.42 (0.0953) |
| 90520-27049 | 3 | 2.48 (0.0976) |
| 90520-27050 | 4 | 2.54 (0.1000) |
| 90520-27051 | 5 | 2.60 (0.1024) |
Using a brass bar and a hammer, install the snap ring onto the input shaft.
| 6. INSTALL 4TH GEAR SYNCHRONIZER RING |
![]() |
Coat the 4th gear synchronizer ring with gear oil and install it onto the No. 2 transmission clutch hub.
| *a | Key Position |
| *b | for 4th Gear |
| 7. INSTALL 4TH GEAR NEEDLE ROLLER BEARING |
![]() |
Coat the 4th gear needle roller bearing and the 4th gear bearing spacer with gear oil and install them onto the No. 2 transmission clutch hub.
| 8. INSTALL 4TH GEAR |
![]() |
Coat the 4th gear with gear oil and install it onto the input shaft.
| 9. INSTALL INPUT SHAFT REAR RADIAL BALL BEARING |
![]() |
Using SST and a press, install the input shaft rear radial ball bearing onto the input shaft.
![]() |
Select a snap ring that will allow minimum axial play.
| Part No. | Mark | Thickness mm (in.) |
| 90520-22006 | A | 2.29 (0.0902) |
| 90520-22007 | B | 2.35 (0.0925) |
| 90520-22008 | C | 2.41 (0.0949) |
| 90520-22009 | D | 2.47 (0.0972) |
| 90520-22010 | E | 2.53 (0.0996) |
| 90520-22011 | F | 2.59 (0.1020) |
Using a brass bar and a hammer, install the snap ring onto the input shaft.
| 10. INSPECT 3RD GEAR RADIAL CLEARANCE |
![]() |
Using a dial indicator, measure the 3rd gear radial clearance between the 3rd gear and input shaft.
| 11. INSPECT 4TH GEAR RADIAL CLEARANCE |
![]() |
Using a dial indicator, measure the 4th gear radial clearance between the 4th gear and input shaft.
| 12. INSPECT 3RD GEAR THRUST CLEARANCE |
![]() |
Using a dial indicator, measure the 3rd gear thrust clearance.
| 13. INSPECT 4TH GEAR THRUST CLEARANCE |
![]() |
Using a feeler gauge, measure the 4th gear thrust clearance.