Home › Suspension › ALIGNMENT / HANDLING DIAGNOSIS › REAR WHEEL ALIGNMENT

REAR WHEEL ALIGNMENT > INSPECTION

for Preparation Click here


NOTICE:
For vehicles equipped with VSC, if wheel alignment has been adjusted, and if suspension or underbody components have been removed/installed or replaced, be sure to perform the following initialization procedure in order for the system to function normally:
  1. Perform zero point calibration of the yaw rate and acceleration sensor and test mode inspection (Click here).



1. INSPECT TIRES
  1. Check the tires for wear and proper inflation pressure.

    Cold Tire Inflation Pressure 
    Tire Size
    Front
    kPa (kgf/cm2, psi)
    Rear
    kPa (kgf/cm2, psi)
    175/65R14 82T
    220 (2.2, 32)
    220 (2.2, 32)
    175/70R14 84S
    250 (2.5, 36)
    240 (2.4, 35)
    175/65R15 84H
    230 (2.3, 33)
    220 (2.2, 32)
    185/60R15 84H
    220 (2.2, 32)
    220 (2.2, 32)



    C164558
  1. Using a dial indicator, check the tire runout.

    Tire runout:
    1.4 mm (0.0551 in.) or less (Vertical)
    2.0 mm (0.0787 in.) or less (Lateral)



2. MEASURE VEHICLE HEIGHT


C235025E01

Measuring points:
A:
Ground clearance of front wheel center
B:
Ground clearance of front lower arm set front bolt center
C:
Ground clearance of rear wheel center
D:
Ground clearance of axle beam set bolt center

NOTICE:
  1. Before inspecting the wheel alignment, check the vehicle height.
  2. The standard value shown here is a value that is used for adjusting the wheel alignment and does not indicate the height of an actual vehicle.

HINT:
Bounce the vehicle up and down at the corners to stabilize the suspension before inspecting the vehicle height.


Vehicle Height (Unloaded Vehicle) 
Model
Tire Size
Front A-B
Rear C-D
Except for Rough Road Package
175/70 R14
97 mm
(3.82 in.)
32 mm
(1.26 in.)
175/65 R15
97 mm
(3.82 in.)
32 mm
(1.26 in.)
175/65 R14
87 mm
(3.43 in.)
25 mm
(0.98 in.)
185/60 R15
87 mm
(3.43 in.)
24 mm
(0.94 in.)
Rough Road Package
175/65 R14
67 mm
(2.64 in.)
5 mm
(0.20 in.)
185/60 R15
67 mm
(2.64 in.)
4 mm
(0.16 in.)


3. INSPECT CAMBER
  1. Install the camber-caster-kingpin gauge and position the rear wheel on the alignment tester.

  1. Inspect the camber.

    Camber (Unloaded Vehicle) 
    Model
    Tire Size
    Camber
    Right - Left Error
    Except for Rough Road Package
    175/70 R14
    -0°57' +/- 30'
    (-0.95° +/- 0.5°)
    0°30'
    (0.5°)
    175/65 R15
    -0°57' +/- 30'
    (-0.95° +/- 0.5°)
    0°30'
    (0.5°)
    175/65 R14
    -0°57' +/- 30'
    (-0.95° +/- 0.5°)
    0°30'
    (0.5°)
    185/60 R15
    -0°57' +/- 30'
    (-0.95° +/- 0.5°)
    0°30'
    (0.5°)
    Rough Road Package
    175/65 R14
    -0°54' +/- 30'
    (-0.90° +/- 0.5°)
    0°30'
    (0.5°)
    185/60 R15
    -0°54' +/- 30'
    (-0.90° +/- 0.5°)
    0°30'
    (0.5°)

    NOTICE:
    The tolerance for the difference between the left and right wheels is 30' (0.5°) or less for both cambers. If the camber is not within the specified range, inspect the suspension parts and replace them if necessary.



4. INSPECT TOE-IN


A166181E12
Text in Illustration 
V100135
Front

Toe-in (Unloaded Vehicle) 
Model
Tire Size
B - A
Except for Rough Road Package
175/70 R14
3.8 +/- 3.0 mm
(0.150 +/- 0.118 in.)
175/65 R15
3.8 +/- 3.0 mm
(0.150 +/- 0.118 in.)
175/65 R14
3.4 +/- 3.0 mm
(0.134 +/- 0.118 in.)
185/60 R15
3.6 +/- 3.0 mm
(0.142 +/- 0.118 in.)
Rough Road Package
175/65 R14
2.7 +/- 3.0 mm
(0.106 +/- 0.118 in.)
185/60 R15
2.8 +/- 3.0 mm
(0.110 +/- 0.118 in.)
If the toe-in is not within the specified range, inspect the suspension parts and replace them if necessary.


5. PERFORM YAW RATE SENSOR ZERO POINT CALIBRATION
(Click here)