Home › Engine / Hybrid System ยท 2NZ-FE › ENGINE CONTROL › ECM

ECM > INSTALLATION

for Preparation Click here



1. INSTALL NO. 2 ECM BRACKET
  1. Install the No. 2 ECM bracket with the 2 screws.

    Torque:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }



2. INSTALL NO. 1 ECM BRACKET
  1. Install the No. 1 ECM bracket with the 2 screws.

    Torque:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }



3. INSTALL ECM
  1. Install the ECM with the bolt and nut.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    NOTICE:
    If a component has been dropped or subjected to a strong impact, replace it.

  1. Pull down the lever to engage the lock and connect the 2 connectors to the ECM.

    NOTICE:
    Make sure that the levers are securely locked.



4. INSTALL BATTERY CARRIER


A247997
  1. Disengage the 7 wire harness clamps and separate the wire harness from the battery carrier.

  1. Remove the 5 bolts and the battery carrier.



5. INSTALL BATTERY TRAY


6. INSTALL BATTERY
  1. Install the battery onto the vehicle with the battery clamp.

    Torque:
    3.5 N*m{ 36 kgf*cm , 31 in.*lbf }

  1. Connect the cable to the battery terminal.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



7. INSTALL OUTER COWL TOP PANEL (for LHD)
  1. Install the outer cowl top panel with the 8 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Engage the 2 clamps and install the wire harness.



8. INSTALL OUTER COWL TOP PANEL (for RHD)
  1. Install the outer cowl top panel with the 8 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Engage the 2 clamps and install the wire harness.



9. INSTALL INNER COWL TOP TO COWL BRACE (for LHD)
  1. Install the cowl top to cowl brace with the 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



10. INSTALL INNER COWL TOP TO COWL BRACE (for RHD)
  1. Install the cowl top to cowl brace with the 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



11. INSTALL FRONT NO. 1 VENTILATOR SEAL (for LHD)
  1. Engage the clip and install the front No. 1 ventilator seal.



12. INSTALL FRONT NO. 1 VENTILATOR SEAL (for RHD)
  1. Engage the clip and install the front No. 1 ventilator seal.



13. INSTALL FRONT AIR SHUTTER SEAL RH (for LHD)

HINT:
Use the same procedure for the RH and LH sides.



14. INSTALL FRONT AIR SHUTTER SEAL RH (for RHD)

HINT:
Use the same procedure as for the front No. 1 ventilator seal.



15. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
(Click here)