OIL PUMP > INSTALLATION |
| 1. INSTALL OIL PUMP ASSEMBLY |
![]() |
Install 2 new O-rings onto the 2 locations as shown in the illustration.
Apply seal packing to the oil pump assembly, cylinder head and cylinder block as shown in the illustration.

| *a | Seal Packing | *b | Seal Width (Other Part) |
| *c | Seal Width (Water Pump Part) | - | - |
![]() |
Align the keyway of the oil pump rotor with the rectangular portion of the crankshaft, and slide the oil pump into place.
![]() |
Install the oil pump assembly with the 15 bolts and the nut. Tighten the bolts and nut uniformly in several steps.
| 2. INSTALL TRANSVERSE ENGINE ENGINE MOUNTING BRACKET |
Install the transverse engine engine mounting bracket with the 4 bolts.
| 3. INSTALL WATER PUMP ASSEMBLY |
Install the water pump assembly through a new water pump gasket with the 3 bolts and 2 nuts.
| 4. INSTALL WATER PUMP PULLEY |
Temporarily install the water pump pulley with the 3 bolts.
Using SST, hold the water pump pulley.
Tighten the 3 bolts to the specified torque.
| 5. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY |
Apply a light coat of engine oil to a new O-ring and install it onto the camshaft timing oil control valve assembly.
Apply a light coat of engine oil to the O-ring and install the camshaft timing oil control valve assembly with the bolt.
Connect the camshaft timing oil control valve assembly connector.
| 6. INSTALL CRANKSHAFT POSITION SENSOR |
Apply a light coat of engine oil to the O-ring.
Install the crankshaft position sensor with the bolt.
Connect the crankshaft position sensor connector.
| 7. INSTALL CRANKSHAFT DAMPER SUB-ASSEMBLY |
Align the pin hole of the crankshaft damper with the pin and install the crankshaft damper sub-assembly.
Provisionally install the bolt.
Using 2 SST, tighten the bolt while holding the crankshaft damper sub-assembly.
| 8. INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH |
Install the engine mounting insulator sub-assembly RH with the 4 bolts and 2 nuts.
| 9. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY |
![]() |
![]() | Seal Packing |
Apply seal packing to the cylinder head as shown in the illustration.
![]() |
Install the cylinder head cover sub-assembly with the 9 bolts, 2 nuts and 2 seal washers.
Tighten the 9 bolts and 2 nuts in the sequence shown in the illustration.
for LHD:
Connect the connector and 4 wire harness clamps and connect the engine wire harness.
Install the wire harness bracket with the bolt.
for RHD:
Connect the connector and 3 wire harness clamps and connect the engine wire harness.
Connect the 4 fuel injector connectors.
| 10. INSTALL FUEL VAPOR FEED HOSE ASSEMBLY |
Connect fuel vapor feed hose assembly.
| 11. INSTALL VENTILATION HOSE |
Connect the ventilation hose.
| 12. INSTALL NO. 1 IGNITION COIL |
Install the 4 No. 1 ignition coils with the 4 bolts.
![]() |
| *1 | Body |
| *2 | Cap |
Connect the 4 No. 1 ignition coil connectors.
| 13. INSTALL GENERATOR ASSEMBLY |
| 14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 15. ADD ENGINE OIL |
Add fresh engine oil.
| Oil Grade | Oil Viscosity (SAE) |
| API grade SL "energy-conserving", API grade SM "energy-conserving" or ILSAC multigrade engine oil |
|
| API grade SL or SM multigrade engine oil |
|
| Item | Capacity |
| Drain and refill with oil filter change | 3.7 liters (3.9 US qts, 3.3 Imp. qts) |
| Drain and refill without oil filter change | 3.4 liters (3.6 US qts, 3.0 Imp. qts) |
| Dry fill | 4.1 liters (4.3 US qts, 3.6 Imp. qts) |
| 16. ADD COOLANT |
Tighten the cylinder block drain cock plug and the radiator drain cock plug.
Pour engine coolant into the radiator assembly until it is full.
Check the coolant level inside the radiator assembly by squeezing the No. 2 radiator hose and the No. 3 radiator hose several times by hand. If the coolant level goes down, add engine coolant.
Install the water filler cap sub-assembly securely.
Slowly pour coolant into the radiator reservoir until it reaches the FULL line.
Bleed air from the cooling system.
Warm up the engine until the thermostat opens.
While the thermostat is open, circulate the coolant for several minutes.
Maintain the engine speed at 2500 to 3000 rpm.
Press the No. 2 radiator hose and No. 3 radiator hose several times by hand to bleed air.
Stop the engine and wait until the coolant cools down.
If the coolant level is below the full level, perform steps (b) through (g) again and repeat the operation until the coolant level stays at the full level.
Recheck the coolant level inside the radiator reservoir tank assembly. If it is below the full level, add coolant.
| 17. INSPECT ENGINE OIL LEVEL |
Warm up and stop the engine, and then wait for 5 minutes.
Check that the engine oil level is between the low level and full level marks on the engine oil level dipstick.
If low, check for leakage and add oil up to the full level mark.
| 18. INSPECT FOR OIL LEAK |
| 19. INSPECT FOR COOLANT LEAK |
![]() |
Fill the radiator assembly with engine coolant, then attach a radiator cap tester.
| *1 | Radiator Cap Tester |
Pump the tester to 137 kPa (1.4 kgf/cm2, 19.9 psi), then check that the pressure does not drop.
If the pressure drops, check the hoses, radiator assembly and water pump assembly for leakage. If there are no signs or traces of external engine coolant leakage, check the heater core, cylinder block and head.
| 20. INSTALL NO. 2 CYLINDER HEAD COVER |
Install the No. 2 cylinder head cover with the 4 nuts.
| 21. INSTALL ENGINE UNDER COVER LH (for Plastic Type) |
| 22. INSTALL ENGINE UNDER COVER RH (for Plastic Type) |
| 23. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (for Metal Type) |
| 24. INSTALL FRONT WHEEL RH |