Home › Engine / Hybrid System ยท 2NZ-FE › LUBRICATION › OIL PUMP

OIL PUMP > INSTALLATION

for Preparation Click here



1. INSTALL OIL PUMP ASSEMBLY


A116556
  1. Install 2 new O-rings onto the 2 locations as shown in the illustration.



  1. Apply seal packing to the oil pump assembly, cylinder head and cylinder block as shown in the illustration.


    A264211E01


    Text in Illustration 
    *a
    Seal Packing
    *b
    Seal Width (Other Part)
    *c
    Seal Width (Water Pump Part)
    -
    -

    Seal packing:
    Water pump part Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent
    Other part Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    NOTICE:
    1. Remove any oil from the contact surfaces.
    2. Install the oil pump assembly within 3 minutes and tighten the bolts and nut within 15 minutes of applying seal packing.
    3. Do not expose the seal to engine oil for at least 2 hours after the installation.



    A116558
  1. Align the keyway of the oil pump rotor with the rectangular portion of the crankshaft, and slide the oil pump into place.



    A116554E01
  1. Install the oil pump assembly with the 15 bolts and the nut. Tighten the bolts and nut uniformly in several steps.

    Torque:
    bolt A:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }
    bolt B:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }
    bolt C:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }
    nut D:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }
    bolt E:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

    NOTICE:
    After installing the oil pump assembly, install the mounting bracket and water pump within 15 minutes.

    HINT:
    Each bolt length is as follows.
    A: 30 mm (1.181 in.)
    B: 35 mm (1.378 in.)
    C: 20 mm (0.787 in.)
    E: 14 to 20 mm (0.551 to 0.787 in.), Double ended bolt



2. INSTALL TRANSVERSE ENGINE ENGINE MOUNTING BRACKET
  1. Install the transverse engine engine mounting bracket with the 4 bolts.

    Torque:
    55 N*m{ 561 kgf*cm , 41 ft.*lbf }



3. INSTALL WATER PUMP ASSEMBLY
  1. Install the water pump assembly through a new water pump gasket with the 3 bolts and 2 nuts.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }



4. INSTALL WATER PUMP PULLEY
  1. Temporarily install the water pump pulley with the 3 bolts.

  1. Using SST, hold the water pump pulley.

    SST
    09960-10010   (09962-01000, 09963-00700)

  1. Tighten the 3 bolts to the specified torque.

    Torque:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }



5. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
  1. Apply a light coat of engine oil to a new O-ring and install it onto the camshaft timing oil control valve assembly.

    HINT:
    Do not twist the O-ring.

  1. Apply a light coat of engine oil to the O-ring and install the camshaft timing oil control valve assembly with the bolt.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the camshaft timing oil control valve assembly connector.



6. INSTALL CRANKSHAFT POSITION SENSOR
  1. Apply a light coat of engine oil to the O-ring.

    NOTICE:
    If reusing the camshaft position sensor, be sure to inspect the O-ring.

  1. Install the crankshaft position sensor with the bolt.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

    NOTICE:
    1. Do not twist the O-ring.
    2. If a component has been dropped or subjected to a strong impact, replace it.

  1. Connect the crankshaft position sensor connector.



7. INSTALL CRANKSHAFT DAMPER SUB-ASSEMBLY
  1. Align the pin hole of the crankshaft damper with the pin and install the crankshaft damper sub-assembly.

  1. Provisionally install the bolt.

  1. Using 2 SST, tighten the bolt while holding the crankshaft damper sub-assembly.

    SST
    09213-14010   (91651-60865)
    09330-00021  

    Torque:
    128 N*m{ 1305 kgf*cm , 95 ft.*lbf }

    NOTICE:
    Check the SST installation positions when installing them, to avoid the SST fixing bolts from coming into contact with the oil pump assembly.



8. INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH
  1. Install the engine mounting insulator sub-assembly RH with the 4 bolts and 2 nuts.

    Torque:
    52 N*m{ 530 kgf*cm , 38 ft.*lbf }



9. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY


    A115489
  1. Disconnect the fuel injector connectors.



  1. for LHD:



      A260540
    1. Disconnect the connector and 4 wire harness clamps shown in the illustration and disconnect the engine wire harness.



    2. A115491
    3. Remove the bolt and the wire harness bracket.



  1. for RHD:



      A260541
    1. Disconnect the connector and 3 wire harness clamps shown in the illustration and disconnect the engine wire harness.



    A066472
  1. Remove the 9 bolts, 2 nuts and 2 seal washers and then remove the cylinder head cover sub-assembly.



10. INSTALL FUEL VAPOR FEED HOSE ASSEMBLY
  1. Connect fuel vapor feed hose assembly.



11. INSTALL VENTILATION HOSE
  1. Connect the ventilation hose.



12. INSTALL NO. 1 IGNITION COIL
(Click here)


13. INSTALL GENERATOR ASSEMBLY
(Click here)


14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



15. ADD ENGINE OIL
  1. Add fresh engine oil.

    Standard Oil Grade:

    Oil Grade
    Oil Viscosity (SAE)
    API grade SL "energy-conserving", API grade SM "energy-conserving" or ILSAC multigrade engine oil
    1. 5W-30
    1. 10W-30
    API grade SL or SM multigrade engine oil
    1. 15W-40
    1. 20W-50


    Oil capacity:

    Item
    Capacity
    Drain and refill with oil filter change
    3.7 liters (3.9 US qts, 3.3 Imp. qts)
    Drain and refill without oil filter change
    3.4 liters (3.6 US qts, 3.0 Imp. qts)
    Dry fill
    4.1 liters (4.3 US qts, 3.6 Imp. qts)



16. ADD COOLANT
  1. Tighten the cylinder block drain cock plug and the radiator drain cock plug.

    Torque:
    13 N*m{ 133 kgf*cm , 9.6 ft.*lbf }

  1. Pour engine coolant into the radiator assembly until it is full.

    Standard capacity:
    5.0 liters (5.3 US qts, 4.4 Imp. qts)

    NOTICE:
    Do not substitute water for coolant.

    HINT:
    1. Use of improper engine coolant may damage the engine coolant system.
    2. Use only Toyota Super Long Life Coolant or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate engine coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).

  1. Check the coolant level inside the radiator assembly by squeezing the No. 2 radiator hose and the No. 3 radiator hose several times by hand. If the coolant level goes down, add engine coolant.

  1. Install the water filler cap sub-assembly securely.

  1. Slowly pour coolant into the radiator reservoir until it reaches the FULL line.

  1. Bleed air from the cooling system.

    1. Warm up the engine until the thermostat opens.
      While the thermostat is open, circulate the coolant for several minutes.

      HINT:
      The thermostat open timing can be confirmed by pressing the No. 2 radiator hose by hand, and checking when the coolant starts to flow inside the hose.

    2. Maintain the engine speed at 2500 to 3000 rpm.

    3. Press the No. 2 radiator hose and No. 3 radiator hose several times by hand to bleed air.

      CAUTION:
      When pressing the radiator hoses:
      1. Wear protective gloves.
      2. Be careful as the radiator hoses are hot.
      3. Keep your hands away from the radiator fan.

  1. Stop the engine and wait until the coolant cools down.

  1. If the coolant level is below the full level, perform steps (b) through (g) again and repeat the operation until the coolant level stays at the full level.

  1. Recheck the coolant level inside the radiator reservoir tank assembly. If it is below the full level, add coolant.



17. INSPECT ENGINE OIL LEVEL
  1. Warm up and stop the engine, and then wait for 5 minutes.

  1. Check that the engine oil level is between the low level and full level marks on the engine oil level dipstick.
    If low, check for leakage and add oil up to the full level mark.

    NOTICE:
    Do not fill with engine oil above the full level mark.



18. INSPECT FOR OIL LEAK


19. INSPECT FOR COOLANT LEAK

CAUTION:
To avoid the danger of being burned, do not remove the water filler cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.



    A250661E01
  1. Fill the radiator assembly with engine coolant, then attach a radiator cap tester.
    Text in Illustration 
    *1
    Radiator Cap Tester

  1. Pump the tester to 137 kPa (1.4 kgf/cm2, 19.9 psi), then check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator assembly and water pump assembly for leakage. If there are no signs or traces of external engine coolant leakage, check the heater core, cylinder block and head.



20. INSTALL ENGINE UNDER COVER LH (for Plastic Type)

Torque:
5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



21. INSTALL ENGINE UNDER COVER RH (for Plastic Type)

Torque:
5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



22. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (for Metal Type)

Torque:
18 N*m{ 184 kgf*cm , 13 ft.*lbf }



23. INSTALL FRONT WHEEL RH

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }