Home › Engine / Hybrid System ยท 1NZ-FE › ENGINE MECHANICAL › CYLINDER BLOCK

CYLINDER BLOCK > INSPECTION

for Preparation Click here



1. INSPECT CONNECTING ROD THRUST CLEARANCE


A037347E01
  1. Using a dial indicator, measure the thrust clearance while moving the connecting rod back and forth.

    Standard thrust clearance:
    0.16 to 0.36 mm (0.0063 to 0.0142 in.)

    Maximum thrust clearance:
    0.36 mm (0.0142 in.)



2. INSPECT CONNECTING ROD OIL CLEARANCE
  1. Check that the matchmarks on the connecting rod and cap are aligned to ensure correct reassembly.



    A037361E02
  1. Using SST, remove the 2 connecting rod cap bolts.

    SST
    09205-16011  

  1. Clean the crank pin and bearing.

  1. Check the crank pin and bearing for pitting and scratches.



    A050668E04
  1. Lay a strip of Plastigage across the crank pin.
    Text in Illustration 
    *1
    Plastigage



    A050673E05
  1. Make sure that the connecting rod and its cap are in the correct combination and that the front mark on the cap is facing in the correct mounting orientation, then install the cap onto the connecting rod.
    Text in Illustration 
    *a
    Front Mark

  1. Apply a light coat of engine oil to the threads of the connecting rod cap bolts.



    A037360E03
  1. Using SST, tighten the bolts in several steps to the specified torque.

    SST
    09205-16011  

    Torque:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }



    A065715E05
  1. Mark the front of the connecting cap bolts with paint.
    Text in Illustration 
    *a
    Paint Mark
    V100136
    Engine Front

  1. Further tighten the cap bolts by 90° as shown in the illustration.

    NOTICE:
    Do not turn the crankshaft.

  1. Remove the 2 bolts, connecting rod cap and lower bearing.



    A037349E03
  1. Measure the Plastigage at its widest point.
    Text in Illustration 
    *1
    Plastigage

    Standard oil clearance:
    0.012 to 0.038 mm (0.00047 to 0.0015 in.)

    NOTICE:
    Completely remove the Plastigage after the measurement.



    A051826E05
  1. When replacing a bearing, replace it with one with the same number as marked on the connecting rod. There are 3 sizes of standard bearings, marked 1, 2 and 3 accordingly.
    Text in Illustration 
    *a
    Mark 1,2 or 3
    *b
    Front Mark
    Standard bearing center wall thickness 
    Mark
    mm (in.)
    1
    1.491 to 1.494 (0.0587 to 0.0588)
    2
    1.494 to 1.497 (0.0588 to 0.0589)
    3
    1.497 to 1.500 (0.0589 to 0.0591)



3. INSPECT CRANKSHAFT THRUST CLEARANCE


A037350E01
  1. Using a dial indicator, measure the thrust clearance while moving the crankshaft back and forth with a screwdriver.

    Standard thrust clearance:
    0.09 to 0.19 mm (0.0035 to 0.0075 in.)

    Maximum thrust clearance:
    0.30 mm (0.0118 in.)

    If the thrust clearance is greater than the maximum, replace the thrust washers as a set. Check the crankshaft and block for wear. Repair or replace the parts if necessary.

    HINT:
    Thrust washer thickness: 2.43 to 2.48 mm (0.0957 to 0.976 in.)



4. INSPECT CYLINDER BLOCK FOR WARPAGE


A037353E06
  1. Using a precision straightedge and feeler gauge, measure the warpage of the surface which is in contact with the cylinder head gasket.
    Text in Illustration 
    *1
    Straightedge

    Maximum warpage:
    0.05 mm (0.0020 in.)



5. INSPECT CYLINDER BORE


A081899E06
  1. Using a cylinder gauge, measure the cylinder bore diameter at positions A and B in the thrust and axial directions.
    Text in Illustration 
    *a
    Thrust Direction
    *b
    Axial Direction
    *c
    Center
    V100135
    Engine Front

    Standard inside diameter:
    75.000 to 75.013 mm (2.9528 to 2.9533 in.)

    Maximum diameter:
    75.013mm (2.9533 in.)

  1. Calculate the difference between the maximum diameter and the minimum diameter of the 4 measured values.

    Difference limit:
    0.10 mm (0.0039 in.)

    If the difference is greater than the limit, replace the cylinder block.



6. INSPECT WITH PIN PISTON SUB-ASSEMBLY


A050666E04
  1. Using a micrometer, measure the piston diameter at a right angle to the piston pin center line, and at the position 27.6 to 27.8 mm (1.0866 to 1.0945 in.) from top of the piston head.

    Piston diameter:
    74.935 to 74.945 mm (2.9502 to 2.9506 in.)

  1. Using a caliper gauge, measure the piston pin hole diameter.

    Piston pin hole diameter:
    18.013 to 18.016 mm (0.7092 to 0.7093 in.) at 20°C (68°F)



    EM00227
  1. Using a micrometer, measure the piston pin diameter.

    Piston pin diameter:
    18.001 to 18.004 mm (0.7087 to 0.7088 in.)

  1. Subtract the piston pin diameter measurement from the piston pin hole diameter measurement to calculate the oil clearance.

    Standard oil clearance:
    0.009 to 0.015 mm (0.0004 to 0.0006 in.)

    Maximum oil clearance:
    0.050 mm (0.0020 in.)

    If necessary, replace the piston and piston pin together.



7. INSPECT PISTON CLEARANCE
  1. Subtract the piston diameter measurement from the cylinder bore diameter measurement to calculate the oil clearance.

    Standard oil clearance:
    0.045 to 0.068 mm (0.0018 to 0.0027 in.)

    Maximum oil clearance:
    0.08 mm (0.0032 in.)



8. INSPECT RING GROOVE CLEARANCE


A001171E01
  1. Using a feeler gauge, measure the clearance between a new piston ring and the wall of the ring groove.

    Ring groove clearance:
    No. 1:
    0.03 to 0.07 mm (0.0012 to 0.0028 in.)
    No. 2:
    0.02 to 0.06 mm (0.0008 to 0.0024 in.)
    oil:
    0.07 to 0.13 mm (0.0028 to 0.0052 in.)



9. INSPECT PISTON RING END GAP


A037354E04
  1. Using a piston, push the piston ring, a little beyond the bottom of the ring travel, 110 mm (4.33 in.) from the top of the cylinder block.



    EM07639
  1. Using a feeler gauge, measure the end gap.

    Standard end gap:
    No. 1:
    0.18 to 0.28 mm (0.0071 to 0.0110 in.)
    No. 2:
    0.35 to 0.50 mm (0.0138 to 0.0197 in.)
    Oil (Side Rail):
    0.10 to 0.35 mm (0.0039 to 0.0138 in.)

    Maximum end gap:
    No. 1:
    0.91 mm (0.0358 in.)
    No. 2:
    1.06 mm (0.0417 in.)
    Oil (Side Rail):
    0.82 mm (0.323 in.)



10. INSPECT CONNECTING ROD BOLT


A001470
  1. Using a vernier caliper, measure the diameter of the bolt at the elongated portion.

    Standard diameter:
    6.6 to 6.7 mm (0.260 to 0.264 in.)

    Minimum diameter:
    6.4 mm (0.252 in.)

    If the diameter is less than the minimum, replace the bolt.



11. INSPECT CRANKSHAFT


A011241E01
  1. Using a dial indicator and V-blocks, measure the circle runout as shown in the illustration.

    Maximum circle runout:
    0.03 mm (0.0012 in.)



    A037157E01
  1. Using a micrometer, measure the diameter of each main journal.

    Outside Diameter:
    45.988 to 46.000 mm (1.8106 to 1.8110 in.)

  1. Check each main journal for taper and out-of-roundness as shown.

    Maximum taper and out-of-roundness:
    0.02 mm (0.0008 in.)



    ZF06928E01
  1. Using a micrometer, measure the diameter of each crank pin.

    Outside Diameter:
    39.992 to 40.000 mm (1.5745 to 1.5748 in.)

  1. Check each crank pin for taper and out-of-roundness as shown.

    Maximum taper and out-of-roundness:
    0.02 mm (0.0008 in.)



    A038171E01
  1. Wrap the chain around the timing sprocket.

  1. Using a vernier caliper, measure the timing sprocket diameter with the chain.

    Standard sprocket diameter (with chain):
    51.72 mm (2.0362 in.)

    Minimum sprocket diameter (with chain):
    50.5 mm (1.988 in.)

    NOTICE:
    Make sure that the vernier caliper is in contact with the chain rollers when measuring.



12. INSPECT CRANKSHAFT BEARING CAP SET BOLT


A015065E03
  1. Using a vernier caliper, measure the tension portion diameter at the elongated portion.

    Standard diameter:
    7.3 to 7.5 mm (0.287 to 0.295 in.)

    Minimum diameter:
    7.2 mm (0.283 in.)

    If the diameter is less than minimum, replace the bolt.



13. INSPECT CRANKSHAFT OIL CLEARANCE
  1. Clean each main journal and bearing.

  1. Install the bearing onto the cylinder block and bearing cap. (Click here)

  1. Place the crankshaft onto the cylinder block.



    A050669E06
  1. Lay a strip of Plastigage across each journal.
    Text in Illustration 
    *1
    Plastigage



    A118660E05
  1. Examine the front marks and numbers and install the bearing cap onto the cylinder block.
    Text in Illustration 
    *1
    No. 3 Bearing Cap
    *2
    No. 1,2,4,5 Bearing Cap
    *a
    Front Mark
    *b
    Number
    *c
    Front Mark and Number

  1. Apply a light coat of engine oil to the threads of the bearing cap bolts.



    A037364E07
  1. Using 12 mm socket wrench, tighten the bolts in several steps to the specified torque in the sequence shown in the illustration. (*1)

    Torque:
    22 N*m{ 224 kgf*cm , 16 ft.*lbf }



    A065715E06
  1. Mark the front of the bearing cap bolts with paint.
    Text in Illustration 
    *a
    Paint Mark
    V100136
    Engine Front

  1. Further tighten the bearing cap bolts by 90° in the same sequence as step (*1).

  1. Check that the painted mark is now at a 90° angle from the front.

    NOTICE:
    Do not turn the crankshaft.

  1. Remove the bearing cap sub-assembly.



    A037352E04
  1. Measure the Plastigage at its widest point.
    Text in Illustration 
    *1
    Plastigage

    Standard oil clearance:
    0.01 to 0.023 mm (0.0004 to 0.0009 in.)

    Maximum oil clearance:
    0.07 mm (0.0028 in.)

    NOTICE:
    Completely remove the Plastigage after the measurement.



    A010463E04
  1. When replacing a standard bearing, replace it with one with the same number. If the number of the bearing cannot be found, select the correct bearing by adding together the numbers imprinted on the cylinder block and crankshaft, then select the bearing with the same number as the total. There are 4 sizes of standard bearings, marked 1, 2, 3 and 4 accordingly.
    Text in Illustration 
    *a
    Mark
    EXAMPLE: Cylinder Block 4 (A) + Crankshaft 3 (B) = Total 7 (Use Bearing 3) 
    Cylinder Block (A)
    +
    Crankshaft (B)
    0 to 2
    3 to 5
    6 to 8
    9 to 11
    Use Bearing
    1
    2
    3
    4

    Item
    Mark
    mm (in.)
    Cylinder block main journal bore diameter (A)
    0
    1
    2
    3
    4
    5
    6
    50.000 to 50.003 (1.96850 to 1.96862)
    50.003 to 50.005 (1.96862 to 1.96870)
    50.005 to 50.007 (1.96870 to 1.96878)
    50.007 to 50.010 (1.96878 to 1.96890)
    50.010 to 50.012 (1.96890 to 1.96898)
    50.012 to 50.014 (1.96898 to 1.96906)
    50.014 to 50.016 (1.96906 to 1.96913)
    Crankshaft main journal diameter (B)
    0
    1
    2
    3
    4
    5
    45.998 to 46.000 (1.81094 to 1.81102)
    45.996 to 45.998 (1.81087 to 1.81094)
    45.994 to 45.996 (1.81079 to 1.81087)
    45.992 to 45.994 (1.81071 to 1.81079)
    45.990 to 45.992 (1.81063 to 1.81071)
    45.988 to 45.990 (1.81055 to 1.81063)
    Standard bearing center wall thickness
    1
    2
    3
    4
    1.992 to 1.995 (0.07843 to 0.07854)
    1.995 to 1.998 (0.07854 to 0.07866)
    1.998 to 2.001 (0.07866 to 0.07878)
    2.001 to 2.004 (0.07878 to 0.07890)