Home › Engine / Hybrid System ยท 2NZ-FE › ENGINE MECHANICAL › ENGINE UNIT

ENGINE UNIT > DISASSEMBLY

for Preparation Click here



1. REMOVE SPARK PLUG


A080968E01
  1. Using a 16 mm spark plug wrench, remove the 4 spark plugs.



2. REMOVE KNOCK SENSOR


A117462
  1. Remove the nut and the knock sensor.



3. REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY


A117463
  1. Using a 24 mm deep socket wrench, remove the engine oil pressure switch.



4. REMOVE ENGINE COOLANT TEMPERATURE SENSOR


A117464
  1. Using a 19 mm deep socket wrench, remove the engine coolant temperature sensor.



5. REMOVE WATER INLET


A080960E01
  1. Remove the 2 nuts and the water inlet.



6. REMOVE THERMOSTAT


A116187
  1. Remove the thermostat.

  1. Remove the gasket from the thermostat.



7. REMOVE OIL FILLER CAP SUB-ASSEMBLY


A080967E01
  1. Remove the oil filler cap from the cylinder head cover.



8. REMOVE OIL FILLER CAP GASKET


    A065656E04
  1. Using a screwdriver with its tip wrapped in protective tape, remove the oil filler gasket from the oil filler cap.
    Text in Illustration 
    *1
    Protective Tape



9. REMOVE CRANKSHAFT POSITION SENSOR
  1. Remove the bolt and the crankshaft position sensor.



10. REMOVE VENTILATION VALVE SUB-ASSEMBLY


A080963E01
  1. Remove the ventilation valve from the cylinder head cover.



11. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY


A066472E01
  1. Remove the 9 bolts, 2 nuts and 2 seal washers and then remove the cylinder head cover.

  1. Remove the gasket from the cylinder head cover.



12. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY


A064872E01
  1. Remove the bolt and the camshaft timing oil control valve.



13. REMOVE OIL LEVEL DIPSTICK GUIDE
  1. Remove the bolt and the oil level dipstick guide.

  1. Remove the O-ring from the oil level dipstick guide.



14. REMOVE WATER PUMP PULLEY


A116191E01
  1. Using SST, hold the water pump pulley.

    SST
    09960-10010   (09962-01000, 09963-00700)

  1. Remove the 3 bolts and the water pump pulley.



15. REMOVE CRANKSHAFT DAMPER SUB-ASSEMBLY


    A116203E11
  1. Set the No. 1 cylinder to TDC/compression.

    1. Turn the crankshaft damper sub-assembly, and align its timing notch with timing mark "0" of the oil pump.
      Text in Illustration 
      *a
      Timing Notch



    2. A116204E11
    3. Check that the timing marks on the camshaft timing sprocket and the camshaft timing gear are all facing upward, as shown in the illustration.
      Text in Illustration 
      *a
      Timing Marks
      If not, turn the crankshaft 1 complete revolution (360°) and align the marks as above.



    A117461E01
  1. Using SST, loosen the bolt while holding the crankshaft damper.

    SST
    09213-14010   (91651-60865)
    09330-00021  

    NOTICE:
    Check the SST installation positions when installing them, to avoid the SST fixing bolts from coming into contact with the oil pump assembly.

  1. Remove the SST.

  1. Remove the bolt and the crankshaft damper.



16. REMOVE TRANSVERSE ENGINE ENGINE MOUNTING BRACKET


A080957E01
  1. Remove the 4 bolts and the transverse engine engine mounting bracket.



17. REMOVE ENGINE WATER PUMP ASSEMBLY


A116192
  1. Remove the 3 bolts, 2 nuts and the engine water pump and gasket.



18. REMOVE OIL PUMP ASSEMBLY


A116554
  1. Remove the 15 bolts and nut.



    A050903E05
  1. Using a screwdriver with its tip wrapped in protective tape, pry the oil pump assembly to remove it.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Do not damage the contact surface of the oil pump assembly and oil pan sub-assembly.



    A116556
  1. Remove the 2 O-rings from the cylinder block and oil pan.



19. REMOVE OIL PUMP SEAL


    A035281E09
  1. Using a screwdriver with its tip wrapped in protective tape, remove the oil pump seal.
    Text in Illustration 
    *1
    Wooden Blocks
    *2
    Protective Tape



20. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY


A156302E01

NOTICE:
  1. Do not rotate the crankshaft with the chain tensioner removed.
  2. When rotating the camshaft with the timing chain removed, rotate the crankshaft counterclockwise 40° from the TDC first, and align the oil jet hole with the paint mark. This prevents the pistons from coming into contact with the valves.
    Text in Illustration 
    *1
    Oil Jet
    *a
    Timing Mark



    A116564E03
  1. Pull up the stopper plate and hold it with its lock released.
    Text in Illustration 
    *1
    Stopper Plate



    A116565E03
  1. Unlock the plunger of the tensioner and push it in to the end.
    Text in Illustration 
    *1
    Plunger



    A116566E03
  1. Pull down the stopper plate with the plunger pushed to the end and lock the plunger.
    Text in Illustration 
    *1
    Stopper Plate



    A116567
  1. Insert a 3 mm (0.12 in.) diameter bar into the hole in the stopper plate and lock the plunger.



    A116568
  1. Remove the 2 bolts and the No. 1 chain tensioner assembly.



21. REMOVE CHAIN TENSIONER SLIPPER


A116569
  1. Remove the chain tensioner slipper.



22. REMOVE NO. 1 CHAIN VIBRATION DAMPER


A116570
  1. Remove the 2 bolts and the No. 1 chain vibration damper.



23. REMOVE CHAIN SUB-ASSEMBLY


24. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY


A115494
  1. Remove the 3 bolts and remove the fuel delivery pipe together with the 4 fuel injectors.

    NOTICE:
    Do not drop the fuel injectors when removing the fuel delivery pipe.



25. REMOVE NO. 1 DELIVERY PIPE SPACER


A115496
  1. Remove the 2 No. 1 delivery pipe spacers.



26. REMOVE INJECTOR VIBRATION INSULATOR


A115497
  1. Remove the 4 injector vibration insulators.



27. REMOVE FUEL INJECTOR ASSEMBLY


A115498
Text in Illustration 
V100135
Pull
  1. Pull the 4 fuel injector assemblies out of the fuel delivery pipe sub-assembly.



28. REMOVE CAMSHAFT POSITION SENSOR


A080958E01
  1. Remove the bolt and the camshaft position sensor.



29. REMOVE NO. 2 CAMSHAFT


A050142E11

NOTICE:
  1. Do not rotate the crankshaft with the chain tensioner removed.
  2. When rotating the camshaft with the timing chain removed, rotate the crankshaft counterclockwise 40° from the TDC first, and align the oil jet hole with the paint mark. This prevents the pistons from coming into contact with the valves.
    Text in Illustration 
    *1
    Oil Jet
    *a
    Timing Mark



    A037074E01
  1. Using several steps, loosen and remove the 11 bearing cap bolts uniformly in the sequence shown in the illustration, then remove the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap and No. 2 camshaft.

    NOTICE:
    Loosen each bolt uniformly while keeping the camshaft level.



30. REMOVE CAMSHAFT TIMING SPROCKET


A064874E01
  1. Clamp the camshaft in a vise, and confirm that it is locked.

    NOTICE:
    Do not damage the camshaft.

  1. Remove the bolt and the camshaft timing sprocket.



31. REMOVE CAMSHAFT


A037075E01
  1. Using several steps, loosen and remove the 8 bearing cap bolts uniformly in the sequence shown in the illustration, then remove the No. 2 camshaft bearing cap and the camshaft.

    NOTICE:
    Loosen each bolt uniformly keeping the camshaft level.



32. REMOVE CAMSHAFT TIMING GEAR ASSEMBLY
  1. Clamp the camshaft in a vise, and confirm that it is locked.

    NOTICE:
    Do not damage the camshaft.



    A116226E08
  1. Cover the 4 oil paths of the cam journal with tape as shown in the illustration.
    Text in Illustration 
    *1
    Rubber Piece
    *2
    Vinyl Tape
    *a
    Advance Side Paths
    *b
    Retard Side Paths
    *c
    Open
    *d
    Closed

    HINT:
    One of the 2 grooves located on the cam journal is for retarding cam timing (upper) and the other is for advancing cam timing (lower). Each groove has 2 oil paths. Plug one of the oil paths for each groove with a piece rubber before wrapping the cam journal with the tape.

  1. Puncture the tape covering the advance oil path and the retard oil path on the opposite side from the advance oil path.



    A116227E05
  1. Apply compressed air at about 150 kPa (1.5 kgf/cm2) pressure into the 2 broken paths (the advance side path and the retard side path).
    Text in Illustration 
    *a
    Retard Side Paths
    *b
    Advance Side Paths

    NOTICE:
    Cover the paths with a piece of cloth to prevent oil splashes.



    A116228E05
  1. Confirm that the camshaft timing gear revolves in the timing advance direction when the air pressure on the timing retard path is reduced.
    Text in Illustration 
    *a
    Retard Side Paths
    *b
    Advance Side Paths
    *c
    Decompress
    *d
    Hold Pressure

    HINT:
    The lock pin is released and the camshaft timing gear revolves in the advance direction.

  1. When the camshaft timing gear reaches the most advanced position, release the air pressure on the timing retard side path, and then release the air pressure on the timing advance side path.

    NOTICE:
    Camshaft timing gear assembly occasionally shifts to the retard side abruptly if the air pressure on the advance side path is released first. It often results in the breakage of the lock pin.



    A116229E05
  1. Remove the bolt and the camshaft timing gear.
    Text in Illustration 
    *a
    Do not remove

    NOTICE:
    1. Do not remove the other 4 bolts.
    2. When reusing the camshaft timing gear, unlock the lock pin inside the camshaft timing gear first.



33. REMOVE CYLINDER HEAD SUB-ASSEMBLY


A035286E01
  1. Using several steps, loosen and remove the 10 cylinder head bolts uniformly with an 8 mm (0.31 in.) bi-hexagon wrench in the sequence shown in the illustration. Remove the 10 cylinder head bolts and the plate washers.

    NOTICE:
    1. Do not drop the washers into the cylinder head.
    2. Head warpage or cracking could result from removing bolts in the wrong order.



34. REMOVE CYLINDER HEAD GASKET


35. REMOVE OIL FILTER SUB-ASSEMBLY


A038018E02
  1. Using SST, remove the oil filter.

    SST
    09228-06501  



36. REMOVE OIL FILTER UNION


A079679E01
  1. Using a 12 mm hexagon wrench, remove the oil filter union.



37. REMOVE ENGINE REAR OIL SEAL


A051764E05
  1. Using a knife, cut off the oil seal lip.
    Text in Illustration 
    *1
    Protective Tape

  1. Using a screwdriver with its tip wrapped in protective tape, pry out the oil seal.

    NOTICE:
    After removal, check the crankshaft for any damage. If damaged, smooth the surface with 400-grit sandpaper.



38. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY
  1. Remove the oil pan drain plug and gasket.



    A079680E01
  1. Remove the 9 bolts and 2 nuts.



    A001456E01
  1. Insert the blade of oil pan seal cutter between the No. 1 oil pan and No. 2 oil pan, and cut off the applied sealer and remove No. 2 oil pan.

    NOTICE:
    Be careful not to damage the contact surfaces of the oil pan.



39. REMOVE OIL STRAINER SUB-ASSEMBLY
  1. Remove the bolt and 2 nuts.

  1. Remove the oil strainer and the gasket.



40. REMOVE OIL PAN SUB-ASSEMBLY


A050902E01
  1. Loosen and remove the 13 bolts uniformly in several steps.



    A011272E01
  1. Using a screwdriver, remove the No. 1 oil pan by prying between the cylinder block and No. 1 oil pan.

    NOTICE:
    Be careful not to damage the contact surfaces of the oil pan.

  1. Remove the 2 O-rings from the cylinder block.



41. REMOVE STUD BOLT


A117459
  1. Using "TORX" socket wrench E5, remove the 4 stud bolts.