Home › Vehicle Interior › DOOR LOCK › FRONT DOOR LOCK

FRONT DOOR LOCK > INSPECTION

for Preparation Click here



1. INSPECT FRONT DOOR LOCK ASSEMBLY LH


    B228534E11
  1. Check the operation of the front door lock motor.
    Text in Illustration 
    *a
    Component without harness connected
    (Front Door Lock Assembly LH)
    *b
    UNLOCK
    *c
    LOCK

    1. Apply battery voltage and check the operation of the front door lock motor.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → 4 (L)
      Battery negative (-) → 1 (UL)
      Locked
      Battery positive (+) → 1 (UL)
      Battery negative (-) → 4 (L)
      Unlocked

      If the result is not as specified, replace the front door lock assembly LH.



    B228534E12
  1. Check the resistance of the unlock detection switch. (for LHD)
    Text in Illustration 
    *a
    Component without harness connected
    (Front Door Lock Assembly LH)
    *b
    UNLOCK
    *c
    LOCK

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      7 (E) - 8 (LSSR)
      Locked
      10 kΩ or higher
      Unlocked
      Below 1 Ω

      If the result is not as specified, replace the front door lock assembly LH.



    B228538E11
  1. Check the resistance of the door lock and unlock switch. (for LHD)
    Text in Illustration 
    *a
    Component without harness connected
    (Front Door Lock Assembly LH)
    *b
    LOCK
    *c
    OFF
    *d
    UNLOCK

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      7 (E) - 9 (L)
      Locked
      Below 1 Ω
      Unlocked
      10 kΩ or higher
      7 (E) - 10 (UL)
      Locked
      10 kΩ or higher
      Unlocked
      Below 1 Ω

      If the result is not as specified, replace the front door lock assembly LH.



2. INSPECT FRONT DOOR LOCK ASSEMBLY RH


    B228535E11
  1. Check the operation of the front door lock motor.
    Text in Illustration 
    *a
    Component without harness connected
    (Front Door Lock Assembly LH)
    *b
    UNLOCK
    *c
    LOCK

    1. Apply battery voltage and check the operation of the front door lock motor.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → 4 (L)
      Battery negative (-) → 1 (UL)
      Locked
      Battery positive (+) → 1 (UL)
      Battery negative (-) → 4 (L)
      Unlocked

      If the result is not as specified, replace the front door lock assembly RH.



    B228535E12
  1. Check the resistance of the unlock detection switch. (for RHD)
    Text in Illustration 
    *a
    Component without harness connected
    (Front Door Lock Assembly LH)
    *b
    UNLOCK
    *c
    LOCK

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      7 (LSSR) - 8 (E)
      Locked
      10 kΩ or higher
      Unlocked
      Below 1 Ω

      If the result is not as specified, replace the front door lock assembly RH.



    B230878E04
  1. Check the resistance of the door lock and unlock switch. (for RHD)
    Text in Illustration 
    *a
    Component without harness connected
    (Front Door Lock Assembly RH)
    *b
    LOCK
    *c
    OFF
    *d
    UNLOCK

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      8 (E) - 6 (L)
      Locked
      Below 1 Ω
      Unlocked
      10 kΩ or higher
      8 (E) - 5 (UL)
      Locked
      10 kΩ or higher
      Unlocked
      Below 1 Ω

      If the result is not as specified, replace the front door lock assembly RH.