Home › Engine / Hybrid System ยท 2NZ-FE › FUEL › FUEL INJECTOR

FUEL INJECTOR > INSTALLATION

for Preparation Click here



1. INSTALL FUEL INJECTOR ASSEMBLY


A115499E04
Text in Illustration 
*1
O-ring
  1. Apply a light coat of gasoline or spindle oil to new O-rings, then install one onto each fuel injector.

  1. Apply a light coat of gasoline or spindle oil to the contact surfaces of the fuel delivery pipe and the O-ring of the fuel injector.



    A260536
  1. While turning the fuel injector left and right, install it onto the fuel delivery pipe.
    Text in Illustration 
    V100135
    Push
    V100136
    Turn

    NOTICE:
    1. Do not twist the O-ring.
    2. After installing the fuel injectors, check that they turn smoothly. If not, replace the O-ring with a new one.



2. INSTALL INJECTOR VIBRATION INSULATOR
  1. Install the 4 new injector vibration insulators onto the cylinder head.



3. INSTALL NO. 1 DELIVERY PIPE SPACER
  1. Install the 2 No. 1 delivery pipe spacers onto the cylinder head.

    NOTICE:
    Install the delivery pipe No. 1 spacer in the correct direction.



4. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY


A115494E02
  1. Install the fuel delivery pipe sub-assembly with the 4 fuel injectors, then provisionally install the 3 bolts.

    NOTICE:
    1. Do not drop the fuel injectors when installing the fuel delivery pipe sub-assembly.
    2. Check that the fuel injectors rotate smoothly after installing the fuel delivery pipe subassembly.

  1. Tighten the 3 bolts to the specified torque.

    Torque:
    Bolt A:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }
    Bolt B:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



5. CONNECT FUEL TUBE SUB-ASSEMBLY


A154755
Text in Illustration 
V100135
Push
  1. Insert the fuel tube connector into the fuel delivery pipe until a click sound can be heard.

    NOTICE:
    1. Check that there are no scratches or foreign matter around the disconnected parts of the fuel tube connector and pipe before performing this work.
    2. After connecting the fuel tube, check that the fuel tube connector and pipe are securely connected by pulling them.

  1. Install the fuel pipe clamp.



6. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY


A260538
Text in Illustration 
V100155
Seal Packing
  1. Apply seal packing to the cylinder head as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    NOTICE:
    1. Remove any oil from the contact surfaces.
    2. Install the cylinder head cover within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.
    3. Do not start the engine for at least 2 hours after the installation.



    A035756E04
  1. Install the cylinder head cover sub-assembly with the 9 bolts, 2 nuts and 2 seal washers.

  1. Tighten the 9 bolts and 2 nuts in the sequence shown in the illustration.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. for LHD:

    1. Connect the connector and 4 wire harness clamps and connect the engine wire harness.

    2. Install the wire harness bracket with the bolt.

      Torque:
      13 N*m{ 130 kgf*cm , 9 ft.*lbf }

  1. for RHD:

    1. Connect the connector and 3 wire harness clamps and connect the engine wire harness.

  1. Connect the 4 fuel injector connectors.



7. INSTALL NO. 1 IGNITION COIL


  1. Install the 4 No. 1 ignition coils with the 4 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


    NOTICE:
    A268161E01
    If the body or cap of the ignition coil is dropped or subjected to a strong impact, replace the ignition coil with a new one.

    Text in Illustration 
    *1
    Body
    *2
    Cap

  1. Connect the 4 No. 1 ignition coil connectors.



8. CONNECT FUEL VAPOR FEED HOSE ASSEMBLY
  1. Connect fuel vapor feed hose assembly.



9. CONNECT VENTILATION HOSE
  1. Connect the ventilation hose.



10. INSPECT FOR FUEL LEAK
  1. Check fuel pump operation.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON and turn the intelligent tester main switch on.

      NOTICE:
      Do not start the engine.

    3. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump /Speed.

    4. Check for pressure in the fuel inlet tube from the fuel line. Check that sounds of fuel flowing from the fuel tank can be heard. If no sounds can be heard, check the integration relay, fuel pump, ECM and wiring connectors.

  1. Inspect for fuel leaks.

    1. Check for fuel leaks from the fuel system after doing any maintenance or repairs. If there is a fuel leak, repair or replace parts if necessary.

  1. Turn the ignition switch off.

  1. Disconnect the intelligent tester from the DLC3.



11. INSPECT FOR ENGINE OIL LEAK


12. INSTALL NO. 2 CYLINDER HEAD COVER
  1. Install the No. 2 cylinder head cover with the 4 nuts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }