Home › Power Source / Network ยท 1NZ-FE BATTERY / CHARGING › GENERATOR

GENERATOR > REASSEMBLY

for Preparation Click here



1. INSTALL GENERATOR ROTOR ASSEMBLY


A033351
  1. Place the generator rotor assembly on the generator drive end frame assembly.

  1. Using a plastic hammer, install the generator rotor assembly to the generator drive end frame assembly.



    A247898
  1. Install a new generator washer on the generator rotor assembly.



    A182592E01
  1. Using a 30 mm/12 pt socket wrench and press, slowly press in the generator rectifier end frame.
    Text in Illustration 
    *1
    30 mm/12 pt Socket Wrench



    A183136E02
  1. Install the 3 nuts A.

    Torque:
    4.5 N*m{ 46 kgf*cm , 40 in.*lbf }

  1. Install the 3 terminal insulators onto the generator rectifier end frame.

  1. Install the cord clip with the nut B.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

    Text in Illustration 
    *1
    Terminal Insulator
    *2
    Cord Clip



2. INSTALL GENERATOR HOLDER WITH RECTIFIER


A219753
  1. Install the generator holder with rectifier with the 3 screws.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }



3. INSTALL GENERATOR REGULATOR ASSEMBLY


A219752
  1. Install the generator regulator assembly with the 2 screws.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }



4. INSTALL GENERATOR BRUSH HOLDER ASSEMBLY


A117359E01
  1. Install the generator plate seal.

  1. Install the generator brush holder assembly with the 3 screws.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }

  1. Install the generator brush cover onto the generator brush holder assembly.
    Text in Illustration 
    *1
    Generator Brush Cover
    *2
    Generator Brush Holder Assembly
    *3
    Generator Plate Seal



    A206812E02
  1. Install the generator rear end cover with the 2 nuts B.

    Torque:
    Nut B:
    4.4 N*m{ 45 kgf*cm , 39 in.*lbf }

  1. Install the rectifier plate with the nut A and screw.

    Torque:
    Nut A:
    4.4 N*m{ 45 kgf*cm , 39 in.*lbf }
    Screw:
    3.9 N*m{ 40 kgf*cm , 35 in.*lbf }

    Text in Illustration 
    *1
    Rectifier Plate



5. INSTALL GENERATOR TERMINAL INSULATOR


    A219750
  1. Install the generator terminal insulator with the nut.

    Torque:
    4.1 N*m{ 42 kgf*cm , 36 in.*lbf }



6. INSTALL GENERATOR PULLEY


A193553E02
  1. Clamp the generator housing stay in a vise tightly.

  1. Install the generator pulley onto the generator rotor shaft by tightening the generator pulley nut by hand.

  1. Hold SST1-A with a torque wrench, and tighten SST1-B clockwise to the specified torque.

    SST
    09820-63011   (09820-06010, 09820-06021)

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }

    Text in Illustration 
    *a
    Hold
    *b
    Turn

    NOTICE:
    Check that SST is securely fitted onto the generator rotor shaft.



    A193554E02
  1. Insert SST2, and engage SST2 to the pulley nut.



    A248835E02
  1. Tighten the generator pulley nut by turning SST1-A in the direction shown in the illustration.
    Text in Illustration 
    *a
    Hold
    *b
    Turn

    Torque:
    137 N*m{ 1397 kgf*cm , 101 ft.*lbf }

    HINT:
    Hold the adjustable wrench against the vise and tighten the nut securely.

  1. Remove SST 2 from the generator assembly.



    A193556E03
  1. Hold SST1-A, turn SST1-B, and remove SST1-A and SST1-B from the generator assembly.
    Text in Illustration 
    *a
    Hold
    *b
    Turn

  1. Turn the generator pulley, and check that the generator pulley moves smoothly.

  1. Remove the generator assembly from a vise.