Home › Drivetrain ยท U441E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE UNIT

AUTOMATIC TRANSAXLE UNIT > INSPECTION

for Preparation Click here



1. INSPECT 2ND COAST AND OVERDRIVE BRAKE DISC


C203928
  1. Check whether the sliding surfaces of the disc, plate and flange are worn or burnt.
    If necessary, replace them.

    NOTICE:
    1. If the lining of the disc is peeling off or discolored, or even if a part of the printed mark is defaced, replace all the discs.
    2. Before assembling new discs, soak them in Toyota Genuine ATF Type T-IV for at least 15 minutes.



2. INSPECT 2ND BRAKE BRAKE DISC


C203929
  1. Check whether the sliding surfaces of the disc, plate and flange are worn or burnt.
    If necessary, replace them.

    NOTICE:
    1. If the lining of the disc is peeling off or discolored, or even if a part of the groove is defaced, replace all the discs.
    2. Before assembling new discs, soak them in Toyota Genuine ATF Type T-IV for at least 15 minutes.



3. INSPECT 1ST AND REVERSE BRAKE DISC


C203930
  1. Check whether the sliding surfaces of the disc, plate and flange are worn or burnt.
    If necessary, replace them.

    NOTICE:
    1. If the lining of the disc is peeling off or discolored, or even if a part of the printed number is defaced, replace all the discs.
    2. Before assembling new discs, soak them in Toyota Genuine ATF Type T-IV for at least 15 minutes.



4. INSPECT DIRECT CLUTCH DISC


C059971
  1. Check whether the sliding surfaces of the disc, plate and flange are worn or burnt.
    If necessary, replace them.

    NOTICE:
    1. If the lining of the disc is peeling off or discolored, or even if a part of the printed number is defaced, replace all the discs.
    2. Before assembling new discs, soak them in Toyota Genuine ATF Type T-IV for at least 15 minutes.



5. INSPECT 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY


C060707
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    15.85 mm (0.6240 in.)

    If the free length is shorter than the standard free length, replace the 2nd brake piston return spring sub-assembly.



6. INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY


C060848
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    21.71 mm (0.85472 in.)

    If the free length is shorter than the standard free length, replace the 1st and reverse brake return spring sub-assembly.



7. INSPECT DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY


C059943
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    36 mm (1.42 in.)

    If the free length is shorter than the standard free length, replace the direct clutch return spring sub-assembly.



8. INSPECT FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY


C060024
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    24.04 mm (0.9465 in.)

    If the free length is shorter than the standard free length, replace the forward clutch return spring sub-assembly.



9. INSPECT OVERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY


C059838
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    18.99 mm (0.748 in.)

    If the free length is shorter than the standard free length, replace the overdrive brake return spring sub-assembly.



10. INSPECT DIRECT CLUTCH PISTON SUB-ASSEMBLY


    C059942
  1. Make sure that the check ball moves freely by shaking the piston.

  1. Check that the valve does not leak by covering the check hole with a finger and applying low pressure compressed air as shown in the illustration.
    If necessary, replace the direct clutch piston sub-assembly



11. INSPECT REAR TRANSAXLE COVER SUB-ASSEMBLY


    C059818
  1. Using a dial indicator, measure the inside diameter of the rear cover bush.

    Standard inside diameter:
    13.94 to 13.96 mm (0.549 to 0.550 in.)

    If necessary, replace the rear transaxle cover sub-assembly.