Home › Drivetrain ยท U441E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE UNIT

AUTOMATIC TRANSAXLE UNIT > DISASSEMBLY

for Preparation Click here



1. REMOVE TRANSMISSION CONTROL SHAFT LEVER


C107764
  1. Remove the nut, washer and transmission control shaft lever.



2. REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY


C057495
  1. Using a screwdriver, pry out the lock plate and remove the nut, lock plate and washer.



    C107763
  1. Remove the 2 bolts and pull out the park/neutral position switch assembly.



3. REMOVE TRANSMISSION REVOLUTION SENSOR


C059782E01
  1. Remove the bolt and the transmission revolution sensor.



    C117099E01
  1. Remove the O-ring from the transmission revolution sensor.
    Text in Illustration 
    *1
    O-ring



4. REMOVE BREATHER PLUG HOSE


C059820E01
  1. Remove the clamp and the breather plug hose.



5. REMOVE OIL COOLER TUBE UNION


C059821E01
  1. Remove the 2 oil cooler tube unions.

  1. Remove the 2 O-rings from the oil cooler tube unions.



6. FIX AUTOMATIC TRANSAXLE ASSEMBLY


    C244602E01
  1. Place the transaxle on wooden blocks.
    Text in Illustration 
    *1
    Wooden Block



7. REMOVE AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY


C203891
  1. Remove the 18 bolts, the automatic transaxle oil pan sub-assembly and the oil pan gasket.

    NOTICE:
    Some fluid will remain in the oil pan. Remove all the oil pan bolts, and carefully remove the automatic transaxle oil pan sub-assembly.



    C057519E01
  1. Remove the 2 oil cleaner magnets from the automatic transaxle oil pan sub-assembly.

  1. Examine the particles in the pan.

    1. Collect any steel chips using the removed magnets.
      Carefully inspect the foreign matter and particles in the pan and on the magnets to guess at the type of wear which might be found in the transaxle.

      1. Steel (magnetic): bearing, gear and clutch plate wear
      2. Brass (non-magnetic): bearing wear



8. REMOVE VALVE BODY OIL STRAINER ASSEMBLY


C203892
  1. Remove the 3 bolts and the valve body oil strainer assembly.



    C057509
  1. Remove the oil strainer gasket from the valve body oil strainer assembly.



9. SEPARATE TRANSMISSION WIRE


    C203893
  1. Disconnect the 5 connectors from the transmission valve body assembly.

  1. Separate the clamp and the transmission wire.



10. REMOVE TRANSMISSION VALVE BODY ASSEMBLY


    C203894
  1. Remove the 14 bolts and the transmission valve body assembly.

    NOTICE:
    Store the bolts so that they can be reinstalled in their original positions because they are of varying lengths.



    C057516E02
  1. Disconnect the manual valve control rod from the manual valve lever, then remove the transmission valve body assembly.



11. REMOVE TRANSMISSION WIRE


    C203904
  1. Remove the bolt.



    C203903
  1. Remove the transmission wire from the transaxle case.



    C067760
  1. Remove the O-ring from the transmission wire.



12. REMOVE NO. 1 GOVERNOR APPLY GASKET


C059784
  1. Using a screwdriver, remove the No. 1 governor apply gasket from the transaxle case.



13. REMOVE CHECK BALL BODY


C059785
  1. Remove the check ball body and the compression spring.



14. REMOVE C-2 ACCUMULATOR PISTON


C203853
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole and remove the C-2 accumulator piston and the C-2 accumulator compression spring.

    NOTICE:
    1. Blowing the air may cause the piston to jump out.
      When removing the piston, hold it by hand using a piece of cloth.
    2. Do not splash ATF with the compressed air.



15. REMOVE C-2 ACCUMULATOR SPRING SUB-ASSEMBLY


C059787
  1. Using a screwdriver, remove the snap ring and the C-2 accumulator spring sub-assembly.



16. REMOVE C-1 ACCUMULATOR PISTON


C203854
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole and remove the C-1 accumulator piston and the C-1 accumulator compression spring.

    NOTICE:
    1. Blowing off the air may cause the piston to jump out.
      When removing the piston, hold it by hand using a piece of cloth.
    2. Do not splash ATF with the compressed air.



17. REMOVE C-1 ACCUMULATOR SPRING SUB-ASSEMBLY


C059790
  1. Using a screwdriver, remove the C-1 accumulator spring.



18. REMOVE B-1 ACCUMULATOR PISTON


C203855
  1. Remove No. 2 B-1 accumulator compression spring.

  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole and remove the B-1 accumulator piston.

    NOTICE:
    1. Blowing the air may cause the piston to jump out.
      When removing the piston, hold it by hand using a piece of cloth.
    2. Do not splash ATF with the compressed air.



19. REMOVE B-1 ACCUMULATOR PISTON COMPRESSION SPRING


C059791
  1. Using a screwdriver, remove the B-1 accumulator piston compression spring.



20. REMOVE TRANSAXLE HOUSING


C203856
  1. Remove the 16 bolts.

  1. Tap around the circumference of the transaxle housing with a plastic hammer to remove the transaxle housing from the transaxle case.

    NOTICE:
    The differential gear assembly may be accidentally removed when the transaxle housing is removed.



21. INSPECT INPUT SHAFT END PLAY


C080727
  1. Using a dial indicator, measure the input shaft end play.

    End play:
    0.3 to 0.9 mm (0.012 to 0.035 in.)



22. REMOVE OIL PUMP ASSEMBLY


C203857
  1. Remove the 6 bolts and the oil pump assembly from the transaxle case.



23. REMOVE INPUT SHAFT ASSEMBLY


C203858
  1. Remove the input shaft assembly from the transaxle case.



24. REMOVE STATOR SHAFT THRUST NEEDLE ROLLER BEARING


C203859
  1. Remove the stator shaft thrust needle roller bearing from the input shaft.



25. REMOVE DIRECT CLUTCH DISC


    C059966
  1. Using a screwdriver, remove the snap ring, direct clutch flange, 2 direct clutch discs and the 2 direct clutch clutch plates from the input shaft.



26. REMOVE DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY


    D025200E01
  1. Using SST, a press and snap ring expander, remove the snap ring and the direct clutch return spring sub-assembly.

    SST
    09387-00020  



27. REMOVE DIRECT CLUTCH PISTON SUB-ASSEMBLY


    C059968
  1. Remove the direct clutch piston sub-assembly by blowing compressed air into the hole as shown in the illustration on the left.



28. REMOVE DIRECT CLUTCH PISTON O-RING


    C059969E01
  1. Remove the direct clutch piston O-ring from the direct clutch piston.



    C059940E01
  1. Remove the direct clutch piston O-ring from the input shaft.



29. REMOVE INPUT SHAFT OIL SEAL RING


    C059970
  1. Remove the 2 input shaft oil seal rings from the input shaft.



30. REMOVE PLANETARY GEAR FRONT THRUST NEEDLE ROLLER BEARING


C203860
  1. Remove the planetary gear front thrust needle roller bearing and the thrust bearing race from the direct clutch hub.



31. REMOVE DIRECT CLUTCH HUB


C203861
  1. Remove the direct clutch hub from the transaxle case.



32. REMOVE DIFFERENTIAL GEAR ASSEMBLY


C203862
  1. Remove the differential gear assembly and the differential drive pinion assembly from the transaxle case.



33. REMOVE NO. 2 GOVERNOR APPLY GASKET


C059803
  1. Remove the No. 2 governor apply gasket from the transaxle case.



34. REMOVE TRANSAXLE REAR COVER ASSEMBLY


C203863
  1. Remove the 9 bolts.

  1. Tap around the circumference of the transaxle rear cover with a plastic hammer to remove the transaxle rear cover assembly from the transaxle case.



35. REMOVE OVERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY


    C248586E01
  1. Using SST and a press, compress the overdrive brake return spring.

    SST
    09387-00070  



    C248587
  1. Using a screwdriver, remove the snap ring and the overdrive brake return spring sub-assembly.



36. REMOVE 2ND COAST AND OVERDRIVE BRAKE PISTON


C203890
  1. Remove the 2nd coast and overdrive brake piston from the transaxle rear cover with compressed air.



37. REMOVE 2ND COAST AND OVERDRIVE O-RING


    C203886
  1. Using a screwdriver, remove the 2 2nd coast and overdrive O-rings from the 2nd coast and overdrive brake piston.



38. REMOVE CLUTCH DRUM OIL SEAL RING


    C203887
  1. Remove the 2 clutch drum oil seal rings from the transaxle rear cover.



39. REMOVE TRANSAXLE REAR COVER PLUG


    C203888
  1. Remove the 3 transaxle rear cover plugs from the transaxle rear cover.

  1. Using a screwdriver, remove the O-rings from the transaxle rear cover plug.



40. REMOVE TRANSAXLE CASE 2ND BRAKE GASKET


C203864
  1. Using a screwdriver, remove the 4 transaxle case 2nd brake gaskets.



41. REMOVE FRONT CLUTCH DRUM THRUST NEEDLE ROLLER BEARING


C203865
  1. Using a magnet hand, remove the clutch drum thrust needle roller bearing.



42. REMOVE INTERMEDIATE SHAFT ASSEMBLY


C203866
  1. Remove the intermediate shaft assembly from the transaxle case.



43. REMOVE REVERSE CLUTCH DISC


    C059951
  1. Using a screwdriver, remove the snap ring.

  1. Remove the flange, 2 discs and 2 plates from the intermediate shaft.



44. REMOVE FRONT CLUTCH CLUTCH DISC


    C059952
  1. Using a screwdriver, remove the snap ring.

  1. Remove the flange, 4 plates and 4 discs from the intermediate shaft.



45. REMOVE NO. 1 CLUTCH BALANCER


    D025202E01
  1. Using SST, a press and snap ring expander, remove the snap ring.

    SST
    09387-00020  

  1. Remove the No. 1 clutch balancer from the intermediate shaft.



46. REMOVE FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY


    C059954
  1. Remove the forward clutch return spring sub-assembly from the intermediate shaft.



47. REMOVE FORWARD CLUTCH PISTON


    C059955
  1. Apply compressed air to the transaxle rear cover to remove the forward clutch piston.



48. REMOVE CLUTCH DRUM SUB-ASSEMBLY


    C059956
  1. Apply compressed air to the transaxle rear cover to remove the clutch drum sub-assembly.



49. REMOVE FORWARD CLUTCH PISTON O-RING


    C059957
  1. Using a screwdriver, remove the forward clutch piston O-ring from the intermediate shaft.



50. REMOVE FRONT CLUTCH DRUM O-RING


    C059958
  1. Using a screwdriver, remove the front clutch drum O-ring from the clutch drum.



51. REMOVE INTERMEDIATE SHAFT OIL SEAL RING


    C059959
  1. Using a screwdriver, remove the intermediate shaft oil seal ring from the intermediate shaft.



52. REMOVE SUN GEAR REAR THRUST BEARING


C203867
  1. Remove the sun gear rear thrust bearing and the 2 thrust bearing races from the intermediate shaft.



53. REMOVE 2ND COAST AND OVERDRIVE BRAKE DISC


C203868
  1. Remove the flange, 2 discs and 2 plates from the transaxle case.



54. REMOVE 2ND COAST AND OVERDRIVE BRAKE FLANGE HOLE SNAP RING


C203869
  1. Using a screwdriver, remove the 2nd coast and overdrive flange hole snap ring from the transaxle case.



55. REMOVE FORWARD CLUTCH HUB SUB-ASSEMBLY


C203870
  1. Remove the forward clutch hub sub-assembly from the transaxle case.



56. REMOVE FORWARD CLUTCH HUB THRUST NEEDLE ROLLER BEARING


C059833
  1. Remove the forward clutch hub thrust needle roller bearing from the forward clutch hub.



57. REMOVE FORWARD CLUTCH HUB THRUST BEARING RACE


C059889
  1. Remove the forward clutch hub thrust bearing race from the planetary sun gear.



58. REMOVE REAR PLANETARY SUN GEAR ASSEMBLY


C059834
  1. Remove the rear planetary sun gear assembly from the transaxle case.



59. REMOVE PLANETARY GEAR REAR THRUST NEEDLE ROLLER BEARING


C059836
  1. Remove the planetary gear rear thrust needle roller bearing from the rear planetary sun gear.



60. INSPECT ONE WAY CLUTCH ASSEMBLY


D025181E04
  1. Hold the rear planetary sun gear and turn the one way clutch.
    Text in Illustration 
    *a
    Hold
    *b
    Lock
    *c
    Free

  1. Make sure that the one way clutch turns freely clockwise and locks when turned counterclockwise.



61. REMOVE ONE WAY CLUTCH ASSEMBLY


C203871
  1. Remove the one way clutch assembly and the No. 2 planetary carrier thrust washer from the rear planetary sun gear.



62. REMOVE PLANETARY CARRIER THRUST WASHER


C203872
  1. Remove the planetary carrier thrust washer from the transaxle case.



63. REMOVE PLANETARY SUN GEAR SUB-ASSEMBLY


C203873
  1. Remove the planetary sun gear sub-assembly from the transaxle case.



64. REMOVE FRONT PLANETARY FLANGE FRONT THRUST BEARING RACE


C060847
  1. Remove the front planetary flange front thrust bearing race from the planetary sun gear.



65. REMOVE SECOND BRAKE PISTON ASSEMBLY


C203850E01
  1. Using SST, a press and screwdriver, remove the snap ring.

    SST
    09387-00100  
    09950-70010   (09951-07100)

  1. Remove the second brake piston assembly from the transaxle case.



66. REMOVE 2ND BRAKE PISTON


    C203884E01
  1. Remove the 2nd brake piston from the 2nd brake cylinder with compressed air.



67. REMOVE 2ND BRAKE CYLINDER O-RING


    C203889
  1. Using a screwdriver, remove the 2 2nd brake cylinder O-rings from the 2nd brake piston.



68. REMOVE 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY


C059850
  1. Remove the 2nd brake piston return spring sub-assembly from the transaxle case.



69. REMOVE 2ND BRAKE BRAKE DISC


C059851
  1. Remove the 2 plates, 2 discs and flange from the transaxle case.



70. REMOVE BRAKE DRUM GASKET


C059852
  1. Remove the brake drum gasket from the transaxle case.



71. REMOVE OUTER RACE RETAINER


C059853
  1. Remove the outer race retainer from the transaxle case.



72. INSPECT NO. 2 ONE WAY CLUTCH


    D025182
  1. Check that the planetary gear turns freely counterclockwise and locks when turned clockwise.
    Text in Illustration 
    V100135
    Lock
    V100136
    Free



73. REMOVE NO. 2 ONE WAY CLUTCH


C203874
  1. Remove the No. 2 one way clutch from the transaxle case.



74. REMOVE PLANETARY GEAR ASSEMBLY


C059857
  1. Remove the planetary gear assembly from the transaxle case.



75. REMOVE 1ST AND REVERSE BRAKE DISC


C203851E01
  1. Using SST, a press and screwdriver, remove the snap ring.

    SST
    09387-00100  
    09950-70010   (09951-07100)

  1. Remove the flange, 4 discs and 4 plates from the transaxle case.



76. REMOVE 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY


C059856
  1. Remove the 1st and reverse brake return spring sub-assembly from the transaxle case.



77. REMOVE COUNTER DRIVE GEAR NUT


C080715E01
  1. Using SST, lift the transaxle case.

    SST
    09223-15020  
    09387-00060  



    D025183E01
  1. Using SST and a hammer, release the counter drive gear nut.

    SST
    09930-00010  



    C060713
  1. Using a socket wrench 55 mm, remove the counter drive gear nut from the planetary ring gear flange.

    NOTICE:
    Remove the nut without unstaking the planetary ring gear.
    If a chisel or other tool is used to unstake the planetary ring gear, the impact may damage the bearing.

    HINT:
    Shift the shift lever to P and fix the counter drive gear.



78. REMOVE PLANETARY RING GEAR FLANGE


C203852E01
  1. Using SST and a press, remove the planetary ring gear flange.

    SST
    09950-60010   (09951-00420)
    09950-70010   (09951-07100)



79. REMOVE PLANETARY RING GEAR


C203875
  1. Using a screwdriver, remove the snap ring.

  1. Remove the planetary ring gear from the planetary ring gear flange.



80. REMOVE COUNTER DRIVE GEAR


C059859E01
  1. Install the 3 bolts to the counter drive gear.

    Bolt (M6):
    L = 40 to 80 mm (1.575 to 3.150 in.)
    Pitch = 1.0 mm

  1. Rotate the 3 bolts and remove the counter drive gear.



81. REMOVE 1ST AND REVERSE BRAKE PISTON


C203876
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transaxle case to remove the 1st and reverse brake piston.

    NOTICE:
    1. Blowing the air may cause the piston to jump out when removing the piston, hold it by hand using a piece of cloth.
    2. Do not splash ATF with the compressed air.



82. REMOVE 1ST AND REVERSE BRAKE O-RING


C203877
  1. Remove the 2 1st and reverse brake O-rings from the 1st and reverse brake piston.



83. REMOVE PARKING LOCK PAWL BRACKET


C203878
  1. Remove the 2 bolts and the parking lock pawl bracket.



84. REMOVE MANUAL VALVE LEVER SHAFT


C059861
  1. Using a screwdriver, cut off the manual valve lever shaft spacer to remove the manual valve lever shaft.



    C059887
  1. Using a pin punch and hammer, drive out the spring pin.

  1. Remove the manual valve lever shaft and the manual valve lever.



85. REMOVE PARKING LOCK ROD SUB-ASSEMBLY


C060849
  1. Remove the parking lock rod sub-assembly from the manual valve lever.



86. REMOVE MANUAL DETENT SPRING SUB-ASSEMBLY


C059863
  1. Remove the bolt and the manual detent spring sub-assembly.



87. REMOVE PARKING LOCK PAWL


C059862
  1. Remove the parking lock pawl shaft, parking lock pawl torsion spring and the parking lock pawl.



88. REMOVE NO. 1 TRANSAXLE CASE PLUG


C203879
  1. Remove the 2 No. 1 transaxle case plugs from the transaxle housing.

  1. Using a screwdriver, remove the 2 O-rings from the 2 No. 1 transaxle case plugs.



89. REMOVE NO. 2 TRANSAXLE HOUSING PLUG


C203880
  1. Remove the No. 2 transaxle housing plug from the transaxle case.

  1. Using a screwdriver, remove the O-ring from the No. 2 transaxle housing plug.



90. REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL


C059903
  1. Using a screwdriver, remove the manual valve lever shaft oil seal from the transaxle case.



91. REMOVE NO. 2 TRANSAXLE CASE OIL SEAL


C059848
  1. Using a screwdriver and hammer, remove the No. 2 transaxle case oil seal.



92. REMOVE TRANSAXLE CASE OIL SEAL


C059798
  1. Using a screwdriver and hammer, remove the transaxle case oil seal.



93. REMOVE NO. 1 TRANSMISSION CASE PLATE


C203881
  1. Remove the bolt and the No. 1 transmission case plate from the transaxle case.



94. REMOVE TRANSAXLE HOUSING OIL SEPARATOR


C203882
  1. Remove the 3 bolts and the transaxle housing oil separator from the transaxle housing.



95. REMOVE NO. 1 TRANSAXLE APPLY TUBE CLAMP


C203883
  1. Remove the bolt and the No. 1 transaxle apply tube clamp from the transaxle housing.



96. REMOVE TRANSMISSION LUBE APPLY TUBE


C059794
  1. Remove the transmission lube apply tube from the transaxle housing.

    NOTICE:
    Do not apply excessive force when removing the apply tube.



97. REMOVE DIFFERENTIAL GEAR LUBE APPLY TUBE


C059795
  1. Remove the differential gear lube apply tube from the transaxle housing.

    NOTICE:
    Do not apply excessive force when removing the apply tube.



98. REMOVE NO. 1 BREATHER PLUG


C123279
  1. Remove the No. 1 breather plug from the transaxle case.

  1. Using a screwdriver, remove the O-ring from No. 1 breather plug.