Home › Drivetrain ยท U441E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE UNIT

AUTOMATIC TRANSAXLE UNIT > REASSEMBLY

for Preparation Click here



1. BEARING POSITION



C203905



2. ADJUST TAPERED ROLLER BEARING PRELOAD
  1. Coat the front differential case and bearing with Toyota Genuine ATF Type T-IV, and install them to the transaxle case.

    NOTICE:
    Do not install the drive pinion.



    C203856
  1. Install the transaxle housing to the transaxle case with the 16 bolts.

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }



    D025185E01
  1. Using SST and a torque wrench, measure the preload of the differential gear.

    SST
    09564-32011  

    Preload:
    Bearing
    Standard
    New
    0.78 to 1.37 N*m (8.0 to 13.9 kgf*cm, 6.9 to 12.2 in.*lbf)
    Used
    0.39 to 0.69 N*m (4.0 to 7.0 kgf*cm, 3.5 to 6.1 in.*lbf)

    If the preload is not within the specifications, remove the differential from the transaxle case.
    Select a new transaxle case side adjusting shim in accordance with the following table.

    Adjusting Shim Thickness:
    Mark
    Thickness
    mm (in.)
    Mark
    Thickness
    mm (in.)
    A
    1.80 (0.0709)
    N
    2.26 (0.0890)
    B
    1.85 (0.0728)
    P
    2.29 (0.0902)
    C
    1.90 (0.0748)
    Q
    2.32 (0.0913)
    D
    1.95 (0.768)
    R
    2.35 (0.0925)
    E
    2.00 (0.0787)
    S
    2.40 (0.0945)
    F
    2.05 (0.0807)
    T
    2.45 (0.0965)
    G
    2.08 (0.0819)
    U
    2.50 (0.0984)
    H
    2.11 (0.0831)
    V
    2.55 (0.1004)
    J
    2.14 (0.0843)
    W
    2.60 (0.1024)
    K
    2.17 (0.0854)
    X
    2.65 (0.1043)
    L
    2.20 (0.0866)
    Y
    2.70 (0.1063)
    M
    2.23 (0.0878)
    -
    -



3. INSTALL NO. 1 BREATHER PLUG


C123279
  1. Coat a new O-ring with Toyota Genuine ATF Type T-IV, and install it to the No. 1 breather plug.

  1. Install the No. 1 breather plug to the transaxle case.



4. INSTALL DIFFERENTIAL GEAR LUBE APPLY TUBE


C059795
  1. Install the differential gear lube apply tube to the transaxle housing.

    NOTICE:
    Do not apply excessive force to the apply tube.



5. INSTALL TRANSMISSION LUBE APPLY TUBE


C059794
  1. Install the transmission lube apply tube to the transaxle housing.

    NOTICE:
    Do not apply excessive force to the apply tube.



6. INSTALL NO. 1 TRANSAXLE APPLY TUBE CLAMP


C059824
  1. Install the No. 1 transaxle apply tube clamp to the transaxle housing with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



7. INSTALL TRANSAXLE HOUSING OIL SEPARATOR


C203882
  1. Install the transaxle housing oil separator to the transaxle housing with the 3 bolts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



8. INSTALL NO. 1 TRANSMISSION CASE PLATE


C059802
  1. Install the No. 1 transmission case plate to the transaxle case with the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }



9. INSTALL NO. 1 TRANSAXLE CASE PLUG


C059902E01
  1. Coat 2 new O-rings with Toyota Genuine ATF Type T-IV, and install them to the 2 No. 1 transaxle case plugs.

  1. Install the 2 No. 1 transaxle case plugs to the transaxle housing.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }



10. INSTALL NO. 2 TRANSAXLE HOUSING PLUG


C059823E01
  1. Coat a new O-ring with Toyota Genuine ATF Type T-IV, and install it to the No. 2 transaxle housing plug.

  1. Install the No. 2 transaxle housing plug to the transaxle case.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }



11. INSTALL MANUAL VALVE LEVER SHAFT OIL SEAL


D025186E01
  1. Coat a new manual valve lever shaft oil seal with Toyota Genuine ATF Type T-IV.

  1. Using SST and a hammer, install the manual valve lever shaft oil seal to the transaxle case.

    SST
    09950-60010   (09951-00210)
    09950-70010   (09951-07100)

    Oil seal drive in depth:
    0.75 to 1.25 mm (0.030 to 0.049 in.)



12. INSTALL PARKING LOCK PAWL


C059865
  1. Coat the parking lock pawl shaft with Toyota Genuine ATF Type T-IV.

  1. Install the parking lock pawl shaft, parking lock pawl torsion spring and the parking lock pawl to the transaxle case.

    NOTICE:
    Check that the edge of the torsion spring fits into the groove securely.



13. INSTALL MANUAL DETENT SPRING SUB-ASSEMBLY


C059863
  1. Install the manual detent spring subassembly with the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }



14. INSTALL PARKING LOCK ROD SUB-ASSEMBLY


C060849
  1. Install the parking lock rod sub-assembly to the manual valve lever.



15. INSTALL MANUAL VALVE LEVER SHAFT


C059855E01
  1. Coat the manual valve lever with Toyota Genuine ATF Type T-IV.

  1. Install a new manual valve lever shaft spacer to the manual valve lever.

  1. Install the manual valve lever shaft and the manual valve lever.

    NOTICE:
    Do not damage the oil seal when installing the manual valve lever shaft.

  1. Using a pin punch and hammer, drive in the spring pin.

  1. Turn the spacer and lever shaft to align the small hole for locating the staking position in the spacer with the staking position mark on the lever shaft.
    Using a pin punch, stake the spacer through the small hole.
    Check that the spacer does not turn.



16. INSTALL PARKING LOCK PAWL BRACKET


C203878
  1. Install the parking lock pawl bracket with the 2 bolts.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }



17. INSTALL 1ST AND REVERSE BRAKE O-RING


C203877
  1. Coat 2 new O-rings with Toyota Genuine ATF Type T-IV, and install them to the 1st and reverse brake piston.



18. INSTALL 1ST AND REVERSE BRAKE PISTON


C059900
  1. Coat the 1st and reverse brake piston with Toyota Genuine ATF Type T-IV, and install it to the transaxle case.

    NOTICE:
    Do not damage the O-ring of the 1st and reverse brake piston.



19. INSTALL 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY


C059856
  1. Coat the 1st and reverse brake return spring sub-assembly with Toyota Genuine ATF Type T-IV, and install it to the transaxle case.



20. INSTALL 1ST AND REVERSE BRAKE DISC


C082195E03
  1. Coat the 4 plates, 4 discs and flange with Toyota Genuine ATF Type T-IV, and install them to the transaxle case.
    Text in Illustration 
    *1
    1st and Reverse Brake Disc
    *2
    1st and Reverse Brake Flange
    *3
    1st and Reverse Brake Plate

    NOTICE:
    Before assembling new discs, soak them in Toyota Genuine ATF Type T-IV for at least 15 minutes.



    C060825E01
  1. Using SST, a press and screwdriver, install the snap ring.

    SST
    09387-00100  
    09950-70010   (09951-07100)

    NOTICE:
    Make sure that the snap ring is installed in the groove of the transaxle case correctly.



21. INSPECT PISTON STROKE OF 1ST AND REVERSE BRAKE


D025187E01
  1. Using SST and a dial indicator, measure the 1st and reverse brake piston stroke while applying and releasing compressed air (392 to 785 kPa, 4 to 8 kgf/cm2, 57 to 114 psi).

    SST
    09350-36010   (09350-06110)

    Piston stroke:
    0.791 to 1.489 mm (0.031 to 0.057 in.)

    If the piston stroke is outside the specifications, inspect the discs, plates and flange.



22. INSTALL COUNTER DRIVE GEAR


C080718E01
  1. Using SST and a press, install the counter drive gear.

    SST
    09223-15030  
    09387-00060  
    09950-60020   (09951-00710)
    09950-70010   (09951-07100)

    NOTICE:
    Do not apply excessive force to the transaxle case.



23. INSTALL PLANETARY RING GEAR


C203875
  1. Install the planetary ring gear to the planetary ring gear flange and fix the snap ring using a screwdriver.



24. INSTALL PLANETARY RING GEAR FLANGE


C080719E01
  1. Using SST and a press, install the planetary ring gear flange.

    SST
    09223-15030  
    09387-00060  
    09950-60010   (09951-00500)
    09950-70010   (09951-07100)



25. INSTALL COUNTER DRIVE GEAR NUT
  1. Using a socket wrench 55 mm, install a new counter drive gear nut to the planetary ring gear flange.

    HINT:
    Torque : 100 N*m (1020 kgf*cm, 74 ft.*lbf)



    C060714
  1. Inspect the preload of the counter drive gear bearing.

    Standard preload:
    0.05 to 0.35 N*m (0.5 to 3.5 kgf*cm, 0.45 to 3.09 in.*lbf)

    HINT:
    Tighten the counter drive gear nut gradually so that the preload is within the specifications.



    C080715E01
  1. Using SST, lift the transaxle case.

    SST
    09213-14010  
    09387-00060  



    C060715
  1. Using a chisel and hammer, stake the counter drive gear nut.



26. INSTALL PLANETARY GEAR ASSEMBLY


C059857
  1. Coat the planetary gear with Toyota Genuine ATF Type T-IV, and install it to the transaxle housing.



27. INSTALL NO. 2 ONE WAY CLUTCH


C203874
  1. Coat the No. 2 one way clutch with Toyota Genuine ATF Type T-IV, and install it to the transaxle.



28. INSPECT NO. 2 ONE WAY CLUTCH


    D025182
  1. Check that the planetary gear turns freely counterclockwise and locks when turned clockwise.
    Text in Illustration 
    V100135
    Lock
    V100136
    Free



29. INSTALL OUTER RACE RETAINER


C059853
  1. Install the outer race retainer in the place shown in the illustration (the space between the No. 2 one way clutch outer race and transaxle case). Push the outer race retainer in until it makes a click sound.



30. INSTALL BRAKE DRUM GASKET


C059852
  1. Coat a new brake drum gasket with Toyota Genuine ATF Type T-IV, and install it to the transaxle case.



31. INSTALL 2ND BRAKE BRAKE DISC


D025188E03
  1. Coat the flange, 2 discs and 2 plates with Toyota Genuine ATF Type T-IV, and install them to the transaxle case.
    Text in Illustration 
    *1
    2nd Brake Brake Disc
    *2
    2nd Brake Brake Flange
    *3
    2nd Brake Brake Plate

    NOTICE:
    Before assembling new discs, soak them in Toyota Genuine ATF Type T-IV for at least 15 minutes.



32. INSTALL 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY


C059850
  1. Coat the 2nd brake piston return spring sub-assembly with Toyota Genuine ATF Type T-IV, and install it to the transaxle case.



33. INSTALL 2ND BRAKE CYLINDER O-RING


    C203889
  1. Coat 2 new 2nd brake cylinder O-rings with Toyota Genuine ATF Type T-IV, and install them to the 2nd brake piston.

    NOTICE:
    Do not damage the O-rings.



34. INSTALL 2ND BRAKE PISTON


    C203885
  1. Coat the 2nd brake piston with Toyota Genuine ATF Type T-IV, and install it to the 2nd brake cylinder.

    NOTICE:
    Do not damage the O-rings.



35. INSTALL SECOND BRAKE PISTON ASSEMBLY


C060853
  1. Coat the second brake piston assembly with Toyota Genuine ATF Type T-IV, and install it as shown in the illustration.



    C059837E01
  1. Using SST, a press and screwdriver, install the snap ring.

    SST
    09387-00100  
    09950-70010   (09951-07100)



36. INSTALL FRONT PLANETARY FLANGE FRONT THRUST BEARING RACE


C060847
  1. Coat the front planetary flange front thrust bearing race with Toyota Genuine ATF Type T-IV, and install it to the front planetary sun gear.



37. INSTALL PLANETARY SUN GEAR SUB-ASSEMBLY


C203873
  1. Coat the planetary sun gear sub-assembly with Toyota Genuine ATF Type T-IV, and install it to the transaxle case.



38. INSTALL 2ND COAST AND OVERDRIVE BRAKE FLANGE HOLE SNAP RING


C203869
  1. Using a screwdriver, install the 2nd coast and overdrive flange hole snap ring to the transaxle case.



39. INSTALL PLANETARY CARRIER THRUST WASHER


C203872
  1. Coat the planetary carrier thrust washer with petroleum jelly, and install it to the planetary gear.



40. INSTALL ONE WAY CLUTCH ASSEMBLY


C203871
  1. Coat the No. 2 planetary carrier thrust washer with petroleum jelly.

  1. Install No. 2 planetary carrier thrust washer and the one way clutch to the planetary sun gear.



41. INSPECT ONE WAY CLUTCH ASSEMBLY


D025181E04
  1. Hold the rear planetary sun gear and turn the one way clutch.
    Text in Illustration 
    *a
    Hold
    *b
    Lock
    *c
    Free

  1. Make sure that the one way clutch turns freely counterclockwise and locks when turned clockwise.



42. INSTALL PLANETARY GEAR REAR THRUST NEEDLE ROLLER BEARING


C059836
  1. Coat the planetary gear rear thrust needle roller bearing with Toyota Genuine ATF Type T-IV, and install it to the rear planetary gear.



43. INSTALL REAR PLANETARY SUN GEAR ASSEMBLY


C059834
  1. Coat the rear planetary sun gear assembly with Toyota Genuine ATF Type T-IV, and install it to the transaxle case.



44. INSTALL FORWARD CLUTCH HUB THRUST BEARING RACE


C059889
  1. Coat the forward clutch hub thrust bearing race with Toyota Genuine ATF Type T-IV, and install it to the transaxle case.



45. INSTALL FORWARD CLUTCH HUB THRUST NEEDLE ROLLER BEARING


C059833
  1. Coat the forward clutch hub thrust needle roller bearing with Toyota Genuine ATF Type T-IV, and install it to the forward clutch hub.



46. INSTALL FORWARD CLUTCH HUB SUB-ASSEMBLY


C203870
  1. Coat the forward clutch hub sub-assembly with Toyota Genuine ATF Type T-IV, and install it to the transaxle case.



47. INSTALL INTERMEDIATE SHAFT OIL SEAL RING


    C059959
  1. Coat a new intermediate shaft oil seal ring with Toyota Genuine ATF Type T-IV, and install it to the clutch drum.



48. INSTALL FRONT CLUTCH DRUM O-RING


    C059958
  1. Coat a new front clutch drum O-ring with Toyota Genuine ATF Type T-IV, and install it to the clutch drum.



49. INSTALL FORWARD CLUTCH PISTON O-RING


    C059957
  1. Coat a new forward clutch piston O-ring with Toyota Genuine ATF Type T-IV, and install it to the intermediate shaft.



50. INSTALL CLUTCH DRUM SUB-ASSEMBLY


    C059963
  1. Coat the clutch drum sub-assembly with Toyota Genuine ATF Type T-IV, and install it to the intermediate shaft.



51. INSTALL FORWARD CLUTCH PISTON


    C059964
  1. Coat the forward clutch piston with Toyota Genuine ATF Type T-IV, and install it to the intermediate shaft.



52. INSTALL FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY


    C059954
  1. Coat the forward clutch return spring with Toyota Genuine ATF Type T-IV, and install it to the intermediate shaft.



53. INSTALL NO. 1 CLUTCH BALANCER
  1. Coat the No. 1 clutch balancer with Toyota Genuine ATF Type T-IV, and install it to the intermediate shaft.



    D025202E01
  1. Using SST, a press and snap ring expander, install the snap ring.

    SST
    09387-00020  



54. INSTALL FRONT CLUTCH CLUTCH DISC


    D025203E03
  1. Coat the 4 plated, 4 discs and flange with Toyota Genuine ATF Type T-IV, and install them to the intermediate shaft with the snap ring.
    Text in Illustration 
    *1
    Front Clutch Clutch Disc
    *2
    Front Clutch Clutch Flange
    *3
    Forward Plate



55. INSTALL REVERSE CLUTCH DISC


    D025204E03
  1. Coat the 2 plates, 2 discs and clutch flange with Toyota Genuine ATF Type T-IV, and install them with the snap ring to the intermediate shaft.
    Text in Illustration 
    *1
    Reverse Clutch Disc
    *2
    Reverse Clutch Flange
    *3
    Reverse Clutch Plate



56. INSPECT PACK CLEARANCE OF REVERSE CLUTCH


    C059938
  1. Install the intermediate shaft to the transaxle rear cover.

  1. Using a dial indicator, measure the clearance while applying compressed air (400 kPa, 4.1 kgf/cm2, 58 psi).

    Standard clearance:
    0.4 to 1.0 mm (0.0157 to 0.0394 in.)

    NOTICE:
    If the clearance is outside the specifications, select a new flange.

    Flange Thickness 
    Mark
    Thickness
    1
    3.0 mm (0.118 in.)
    2
    3.2 mm (0.126 in.)
    3
    3.4 mm (0.135 in.)
    4
    3.6 mm (0.142 in.)



57. INSPECT PACK CLEARANCE OF FRONT CLUTCH


    C059939E01
  1. Install the intermediate shaft to the transaxle rear cover.

  1. Using SST and a dial indicator, measure the clearance while applying compressed air (400 kPa, 4.1 kgf/cm2, 58 psi).

    SST
    09350-36010   (09350-06120)

    Standard clearance:
    1.3 to 1.5 mm (0.0512 to 0.0591 in.)

    NOTICE:
    If the clearance is outside the specifications, select a new flange.

    Flange Thickness 
    Mark
    Thickness
    1
    3.0 mm (0.118 in.)
    2
    3.2 mm (0.126 in.)
    3
    3.4 mm (0.135 in.)
    4
    3.6 mm (0.142 in.)



58. INSTALL SUN GEAR REAR THRUST BEARING


C203867
  1. Coat the sun gear rear thrust bearing and the 2 thrust bearing races with Toyota Genuine ATF Type T-IV, and install them to the intermediate shaft.



59. INSTALL INTERMEDIATE SHAFT ASSEMBLY


C203866
  1. Coat the intermediate shaft assembly with Toyota Genuine ATF Type T-IV, and install it to the transaxle case.



60. INSTALL 2ND COAST AND OVERDRIVE BRAKE DISC


D025189E03
  1. Coat the 2 discs and 3 flanges with Toyota Genuine ATF Type T-IV, and install them to the transaxle case.
    Text in Illustration 
    *1
    2nd Coast and Overdrive Brake Disc
    *2
    2nd Coast and Overdrive Brake Flange

    NOTICE:
    Before assembling new discs, soak them in Toyota Genuine ATF Type T-IV for at least 15 minutes.



61. INSTALL TRANSAXLE REAR COVER PLUG


    C203888
  1. Coat 4 new O-rings with Toyota Genuine ATF Type T-IV, and install them to the transaxle rear cover plug.

  1. Install the 3 transaxle rear cover plugs to the transaxle rear cover.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }

    NOTICE:
    Do not damage the O-rings.



62. INSTALL CLUTCH DRUM OIL SEAL RING


    D025205E01
  1. Compress the clutch drum oil seal ring from both sides to reduce dimension A.

    Dimension A:
    5.0 mm (0.197 in.)

  1. Coat the 2 clutch drum oil seal rings with Toyota Genuine ATF Type T-IV, and install them to the transaxle rear cover.



63. INSTALL 2ND COAST AND OVERDRIVE O-RING


    C203886
  1. Coat 2 new 2nd coast and overdrive O-rings with Toyota Genuine ATF Type T-IV, and install them to the 2nd coast overdrive brake piston.

    NOTICE:
    Do not damage the O-rings.



64. INSTALL 2ND COAST AND OVERDRIVE BRAKE PISTON


    C060025
  1. Coat the 2nd coast and overdrive brake piston with Toyota Genuine ATF Type T-IV, and install it to the transaxle rear cover.



65. INSTALL OVERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY


    C248587
  1. Coat the overdrive brake return spring sub-assembly with Toyota Genuine ATF Type T-IV, and install it to the transaxle rear cover.



    C248586E01
  1. Using SST and a press, shorten the overdrive brake return spring, then install the snap ring.

    SST
    09387-00070  



66. INSPECT 2ND COAST AND OVER DRIVE BRAKE FLANGE, DISC AND PLATE


C059893E01
  1. Using a straightedge and vernier caliper, measure dimension A from the transaxle case end surface to the brake flange.



    C059894E01
  1. Using a straightedge and vernier caliper, measure dimension B from the piston to the edge surface of the transaxle rear cover assembly.

  1. Calculate the clearance from the measured dimensions A and B.

    Piston clearance:
    0.65 to 1.05 mm (0.0256 to 0.0413 in.)

    HINT:
    1. Piston clearance = Dimension A - Dimension B.
    2. If the result is not as specified, select a new brake flange.

    Flange Thickness 
    Mark
    Thickness
    mm (in.)
    Piston Stroke Value
    mm (in.)
    0
    3.0
    (0.118)
    0.738 to 0.949
    (0.02905 to 0.03736)
    1
    3.2
    (0.126)
    0.950 to 1.149
    (0.03740 to 0.04524)
    2
    3.4
    (0.134)
    1.150 to 1.349
    (0.04528 to 0.05311)
    3
    3.6
    (0.142)
    1.350 to 1.549
    (0.05315 to 0.06098)
    4
    3.8
    (0.150)
    1.550 to 1.702
    (0.06102 to 0.06701)



67. INSTALL TRANSAXLE CASE 2ND BRAKE GASKET


C203864
  1. Coat 4 new transaxle case 2nd brake gaskets with Toyota Genuine ATF Type T-IV, and install them to the transaxle rear cover.



68. INSTALL FRONT CLUTCH DRUM THRUST NEEDLE ROLLER BEARING


C203865
  1. Coat the front clutch drum thrust needle roller bearing with Toyota Genuine ATF Type T-IV, and install it to the forward and reverse clutch.



69. INSTALL TRANSAXLE REAR COVER ASSEMBLY


C059899E01
  1. Apply a continuous bead of seal packing (Diameter 1.2 mm (0.0472 in.)) to the transaxle rear cover.
    Text in Illustration 
    *a
    Seal Packing
    (Seal Diameter: 1.2 mm (0.0472 in.))

    Seal Packing:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

    NOTICE:
    1. Remove any oil from the contact surfaces.
    2. Assemble the parts within 10 minutes of application. Otherwise, the seal packing material must be removed and reapplied.



    C203863
  1. Install the transaxle rear cover assembly to the transaxle case with the 9 bolts.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }



70. INSTALL NO. 2 GOVERNOR APPLY GASKET


C059803
  1. Coat a new No. 2 governor apply gasket with Toyota Genuine ATF Type T-IV, and install it to the transaxle case.



71. INSTALL DIFFERENTIAL GEAR ASSEMBLY


C203862
  1. Coat the differential gear assembly and the drive pinion assembly with Toyota Genuine ATF Type T-IV, and install them to the transaxle case.



72. INSTALL DIRECT CLUTCH HUB


C203861
  1. Coat the direct clutch hub with Toyota Genuine ATF Type T-IV, and install it to the transaxle case.



73. INSTALL PLANETARY GEAR FRONT THRUST NEEDLE ROLLER BEARING


C203860
  1. Coat the planetary gear front thrust needle roller bearing and the thrust bearing race with Toyota Genuine ATF Type T-IV, and install them to the transaxle case.



74. INSTALL INPUT SHAFT OIL SEAL RING


    C059970
  1. Coat 2 new input shaft oil seal rings with Toyota Genuine ATF Type T-IV, and install them to the input shaft.



75. INSTALL DIRECT CLUTCH PISTON O-RING


    C059969E01
  1. Coat a new direct clutch piston O-ring with Toyota Genuine ATF Type T-IV, and install it to the direct clutch.



    C059940E01
  1. Coat a new direct clutch piston O-ring with Toyota Genuine ATF Type T-IV, and install it to the input shaft.



76. INSTALL DIRECT CLUTCH PISTON SUB-ASSEMBLY


    C059974
  1. Coat the direct clutch piston with Toyota Genuine ATF Type T-IV, and install it to the input shaft.



77. INSTALL DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY


    D025200E01
  1. Using SST, a press and snap ring expander, install the direct clutch return spring subassembly to the input shaft with the snap ring.

    SST
    09387-00020  



78. INSTALL DIRECT CLUTCH DISC


    D025201E04
  1. Coat the direct clutch flange, 2 direct clutch discs and the 2 direct clutch clutch plates with Toyota Genuine ATF Type T-IV, and install them to the input shaft with the snap ring.
    Text in Illustration 
    *1
    Direct Clutch Flange
    *2
    Direct Clutch Disc
    *3
    Direct Clutch Clutch Plate



79. INSPECT PISTON STROKE OF DIRECT CLUTCH


C059977
  1. Install the input shaft assembly onto the oil pump.

  1. Using a dial indicator, measure the clearance while applying compressed air (400 kPa, 4.1 kgf/cm2, 58 psi).

    Standard clearance:
    0.4 to 0.7 mm (0.0157 to 0.0276 in.)

    NOTICE:
    If the clearance is outside the specifications, select a new flange.

    Flange Thickness 
    Mark
    Thickness
    1
    3.0 mm (0.118 in.)
    2
    3.2 mm (0.126 in.)
    3
    3.4 mm (0.135 in.)



80. INSTALL STATOR SHAFT THRUST NEEDLE ROLLER BEARING


C203859
  1. Coat the stator shaft thrust needle roller bearing with Toyota Genuine ATF Type T-IV, and install it to the transaxle case.

    NOTICE:
    Check the direction of the bearing.



81. INSTALL INPUT SHAFT ASSEMBLY


C203858
  1. Coat the input shaft assembly with Toyota Genuine ATF Type T-IV, and install it to the transaxle case.



82. INSTALL OIL PUMP ASSEMBLY


C203857
  1. Place the oil pump assembly through the input shaft, and align the bolt holes in the oil pump assembly with those in the transaxle case.

  1. Install the 6 bolts.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }



83. INSPECT INPUT SHAFT ASSEMBLY


C080729
  1. Make sure that the input shaft turns smoothly.



84. INSPECT INPUT SHAFT END PLAY


C080727
  1. Using a dial indicator, measure the input shaft end play.

    End play:
    0.3 to 0.9 mm (0.012 to 0.035 in.)

    If the end play is not as specified, select and replace the thrust needle roller bearing.



85. INSTALL TRANSAXLE HOUSING


C059886E01
  1. Apply a continuous bead of seal packing (Diameter 1.2 mm (0.0472 in.)) to the transaxle housing.
    Text in Illustration 
    *a
    Seal Packing
    (Seal Diameter: 1.2 mm (0.0472 in.))

    Seal Packing:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

    NOTICE:
    1. Remove any oil from the contact surfaces.
    2. Assemble the parts within 10 minutes of application. Otherwise, the seal packing material must be removed and reapplied.



    C080710E01
  1. Install the transaxle housing to the transaxle case with the 16 bolts.

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }

    HINT:
    Apply adhesive or the equivalent to the 4 bolts indicated by arrows.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



86. INSTALL B-1 ACCUMULATOR PISTON COMPRESSION SPRING


C060004
  1. Install the B-1 accumulator piston compression spring to the B-1 accumulator piston.



87. INSTALL B-1 ACCUMULATOR PISTON


D025193
  1. Coat 2 new O-rings with Toyota Genuine ATF Type T-IV, and install them to the B-1 accumulator piston.



    C060822
  1. Coat the B-1 accumulator piston with Toyota Genuine ATF Type T-IV, and install it to the transaxle case.

  1. Install the No. 2 B-1 accumulator compression spring.



88. INSTALL C-1 ACCUMULATOR SPRING SUB-ASSEMBLY


C059790
  1. Install the C-1 accumulator spring to the C-1 accumulator piston.



89. INSTALL C-1 ACCUMULATOR PISTON


D025194
  1. Coat 2 new O-rings with Toyota Genuine ATF Type T-IV, and install them to the C-1 accumulator piston.



    C203854
  1. Coat the C-1 accumulator piston with Toyota Genuine ATF Type T-IV, and install it to the transaxle case.



90. INSTALL C-2 ACCUMULATOR SPRING SUB-ASSEMBLY


C059787
  1. Using a screwdriver, install the C-2 accumulator spring to the C-2 accumulator piston with the snap ring.



91. INSTALL C-2 ACCUMULATOR PISTON


D025195
  1. Coat 2 new O-rings with Toyota Genuine ATF Type T-IV, and install them to the C-2 accumulator piston.



    C203853
  1. Coat the C-2 accumulator piston with Toyota Genuine ATF Type T-IV, and install it to the transaxle case.



92. INSTALL CHECK BALL BODY


C059785
  1. Coat the compression spring and the check ball body with Toyota Genuine ATF Type T-IV, and install them to the transaxle case.



93. INSTALL NO. 1 GOVERNOR APPLY GASKET


C059784
  1. Coat new No. 1 governor apply gasket with Toyota Genuine ATF Type T-IV, and install it to the transaxle case.



94. INSTALL TRANSMISSION WIRE
  1. Coat a new O-ring with Toyota Genuine ATF Type T-IV, and install it to the transmission wire.



    C203903
  1. Insert the transmission wire into the transaxle case.



    C203904
  1. Install the transmission wire with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



95. INSTALL TRANSMISSION VALVE BODY ASSEMBLY


C057516E02
  1. Connect the manual valve control rod to the manual valve lever, and install the transmission valve body assembly.



    C203895E01
  1. Install the 14 bolts to the positions shown in the illustration and tighten them uniformly.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }

    NOTICE:
    When installing the transmission valve body assembly to the transaxle case, do not hold the solenoids.

    Bolt length:
    Bolt A:
    20 mm (0.787 in.)
    Bolt B:
    28 mm (1.102 in.)
    Bolt C:
    49 mm (1.929 in.)
    Bolt D:
    36 mm (1.417 in.)
    Bolt E:
    40 mm (1.575 in.)



96. CONNECT TRANSMISSION WIRE


    C203893
  1. Install the transmission wire with the clamp.

  1. Connect the 5 connectors to the transmission valve body assembly.



97. INSTALL VALVE BODY OIL STRAINER ASSEMBLY


C057509
  1. Coat a new oil strainer gasket with Toyota Genuine ATF Type T-IV and install it to the valve body oil strainer assembly.



    C203892
  1. Install the valve body oil strainer assembly with the 3 bolts.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }



98. INSTALL AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY


C057519E01
  1. Install the 2 oil cleaner magnets to the 2 positions shown in the illustration.



    C203891
  1. Install a new oil pan gasket and the automatic transaxle oil pan sub-assembly to the transaxle assembly with 18 bolts.

    Torque:
    7.0 N*m{ 70 kgf*cm , 61 in.*lbf }

  1. Install a new gasket and the drain plug to the automatic transaxle oil pan sub-assembly.

    Torque:
    17 N*m{ 175 kgf*cm , 13 ft.*lbf }



99. INSTALL NO. 2 TRANSAXLE CASE OIL SEAL


C203932E01
  1. Using SST and a hammer, install a new No. 2 transaxle case oil seal.

    SST
    09517-12010  
    09630-24014   (09620-24051)

    Drive in depth:
    2.6 to 3.6 mm (0.103 to 0.141 in.)

  1. Apply MP grease to the lip of the No. 2 transaxle case oil seal.



100. INSTALL TRANSAXLE CASE OIL SEAL


C203934E01
  1. Using SST and a hammer, install a new transaxle case oil seal.

    SST
    09316-60011   (09316-00011)

    Drive in depth:
    2.6 to 3.6 mm (0.103 to 0.141 in.)

  1. Apply MP grease to the lip of the transaxle case oil seal.



101. INSTALL OIL COOLER TUBE UNION


C059821E01
  1. Coat 2 new O-rings with ATF Type T-IV, and install them to the 2 oil cooler tube unions.

  1. Install the 2 oil cooler tube unions.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }



102. INSTALL BREATHER PLUG HOSE


C059820E01
  1. Install the breather plug hose to the breather plug with the clamp.



103. INSTALL TRANSMISSION REVOLUTION SENSOR


    C117099E01
  1. Coat a new O-ring with ATF Type T-IV, and install it to the transmission revolution sensor.
    Text in Illustration 
    *1
    O-ring



    C059782E01
  1. Install the transmission revolution sensor to the transaxle assembly with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



104. INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY


C107763
  1. Install the park/neutral position switch assembly.

  1. Temporarily install the 2 bolts.



    C244577
  1. Replace the lock plate with a new one and install the nut, lock plate and washer.

  1. Temporarily install the 2 bolts.

    Torque:
    6.9 N*m{ 70 kgf*cm , 61 in.*lbf }

  1. Temporarily install the control shaft lever.



    C107759
  1. Turn the lever counterclockwise until it stops, then turn it clockwise 2 notches.



    C107760E06
  1. Align the groove and the neutral basic line., and tighten the 2 bolts.
    Text in Illustration 
    *a
    Neutral Basic Line
    *b
    Groove

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



    C107761
  1. Using a screwdriver, stake the nut with the lock washer.



105. INSTALL TRANSMISSION CONTROL SHAFT LEVER


C107764
  1. Install the control shaft lever with the washer and nut.

    Torque:
    12 N*m{ 125 kgf*cm , 9 ft.*lbf }