Home › Drivetrain ยท U441E AUTOMATIC TRANSMISSION / TRANSAXLE › DIFFERENTIAL CASE

DIFFERENTIAL CASE > REASSEMBLY

for Preparation Click here



1. INSTALL DIFFERENTIAL GEAR KIT


C060003E01
  1. Coat the differential gear kit ((2 front differential pinions and 2 front differential side gears), 2 front differential side gear thrust washers and the 2 front differential pinion thrust washers with Toyota Genuine ATF Type T-IV, and install them to the front differential case.



2. INSTALL FRONT NO. 1 DIFFERENTIAL PINION SHAFT


C060001E01
  1. Install the front No. 1 differential pinion shaft so as to align the straight pin holes in the front No. 1 differential pinion shaft and the front differential case.



3. INSPECT DIFFERENTIAL SIDE GEAR BACKLASH


    C060010E01
  1. Using a dial indicator, measure the front differential side gear backlash while holding 1 pinion gear toward the case.

    Standard backlash:
    0.05 to 0.20 mm (0.00197 to 0.00787 in.)

    If the backlash is outside the specifications, install the correct front differential side gear thrust washer to the front differential side gear.

  1. Referring to the table below, select front differential side gear thrust washers which will ensure that the backlash is within the specifications for both sides.

    Thrust Washer Thickness:
    Part No.
    Thickness
    mm (in.)
    41361-52010
    1.50 (0.0589)
    41361-52020
    1.55 (0.0609)
    41361-52030
    1.60 (0.0629)
    41361-52040
    1.65 (0.0649)
    41361-52050
    1.70 (0.0669)
    41361-52060
    1.75 (0.0689)

    If the backlash is not within the specifications, install a front differential side gear thrust washer of a different thickness.



4. INSTALL FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN


C060005E01
  1. Using a pin punch 3 mm and hammer, install the front differential pinion shaft straight pin to the front differential case.



    C060006E01
  1. Using a chisel and hammer, stake the front differential case.



5. INSTALL FRONT DIFFERENTIAL RING GEAR


D025177E01
  1. Using ATF and a heater, heat the front differential ring gear to 90 to 110°C (194 to 230°F).

    CAUTION:
    Use thick gloves to protect your hands as the front differential ring gear is hot.

  1. Clean the contact surface of the front differential case and the front differential ring gear.



    C123274E01
  1. Align the matchmarks on the front differential ring gear and the front differential case, and install the front differential ring gear while it is still hot.
    Text in Illustration 
    *a
    Matchmark



    C123275E01
  1. Tighten the 8 bolts.

    Torque:
    78 N*m{ 790 kgf*cm , 57 ft.*lbf }



6. INSTALL SPEEDOMETER DRIVE GEAR (w/o ABS)


C123273E01
  1. Install the speedometer drive gear to the front differential case.



7. INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING


C123276E01
  1. Using SST and a press, install the front differential case front tapered roller bearing (inner race) to the front differential case.

    SST
    09608-06041  



    D025217E01
  1. Using SST and a hammer, install the front differential case front tapered roller bearing (outer race) to the transaxle housing.

    SST
    09950-60020   (09951-00680)
    09950-70010   (09951-07100)
    09950-60010   (09951-00340)



8. INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING


C123277E01
  1. Using SST and a press, install the front differential case rear tapered roller bearing (inner race) to the front differential case.

    SST
    09608-06041  



    D025219E01
  1. Using SST and a hammer, install the front differential case rear plate washer and the front differential case rear tapered roller bearing (outer race) to the transaxle case.

    SST
    09950-60020   (09951-00710)
    09950-70010   (09951-07100)



9. INSTALL DIFFERENTIAL DRIVE PINION PLUG


C060013E01
  1. Using a socket wrench 10 mm and hammer, install a new differential drive pinion plug to the differential drive pinion.

    Drive in depth:
    2.3 to 2.35 mm (0.0906 to 0.0925 in.)



10. INSTALL FRONT DRIVE PINION FRONT TAPERED ROLLER BEARING


D025220E01
  1. Using SST and a press, install the front drive pinion front tapered roller bearing (inner race) to the differential drive pinion.

    SST
    09608-04031  
    09950-60010   (09951-00540)



    D025227E01
  1. Using SST and a hammer, install the front drive pinion front tapered roller bearing (outer race) to the transaxle housing.

    SST
    09608-04031  
    09950-70010   (09951-07100)



11. INSTALL COUNTER DRIVE GEAR


D025228E01
  1. Using SST and a press, install the counter drive gear to the differential drive pinion.

    SST
    09608-04031  
    09950-60010   (09951-00280)



12. INSTALL FRONT DRIVE PINION REAR TAPERED ROLLER BEARING


D025229E01
  1. Using SST and a press, install the front drive pinion rear tapered roller bearing (inner race) to the differential drive pinion.

    SST
    09608-04031  
    09950-60010   (09951-00280)



    D025230E01
  1. Using SST and a hammer, install the drive pinion washer and the front drive pinion rear tapered roller bearing (outer race) to the transaxle case.

    SST
    09950-60010   (09951-00600)
    09950-70010   (09951-07100)