Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)

AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) > TERMINALS OF ECU

for Preparation Click here



CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
If the result is not as specified, there may be a malfunction in the wire harness.

E228237E01

HINT:
Check from the rear of the connector while it is connected to the air conditioning amplifier assembly.


Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
F42-1 (IG+) - F42-14 (GND)
V - W-B
Ignition power supply
Ignition switch: ON
11 to 14 V
F42-2 (SOL+) - F42-14 (GND)
P - W-B
A/C compressor operation signal
Engine idling
Pulse generation
(See waveform 1)
Blower switch: LO
A/C switch: ON
F42-5 (TAM) - F42-13 (SG-2)
W - L
A/C ambient temperature sensor signal
Ignition switch ON at 25°C (77°F)
1.35 to 1.75 V
F42-9 (PRE) - F42-14 (GND)
GR - W-B
Air conditioning pressure sensor signal
Refrigerant pressure: Normal
0.63 to 4.73 V
Refrigerant pressure: Abnormal (less than 0.176 MPaG [1.8 kgf/cm2]) or more than 3.03 MPaG [31 kgf/cm2])
Below 0.63 V or 4.73 V or more
F42-10 (S5-3) - F42-14 (GND)
Y - W-B
Power supply for pressure sensor
Ignition switch: ON
4.75 to 5.25 V
F42-11 (TX+) - F42-14 (GND)
V - W-B
CAN communication signal
Ignition switch: ON
Pulse generation
(See waveform 2)
F42-12 (TX-) - F42-14 (GND)
W - W-B
CAN communication signal
Ignition switch: ON
Pulse generation
(See waveform 3)
F42-13 (SG-2) - Body ground
L - Body ground
Ground for ambient temperature sensor and A/C pressure sensor
Always
Below 1 Ω
F42-14 (GND) - Body ground
W-B - Body ground
Ground for main power supply
Always
Below 1 Ω
F42-21 (B) - F42-14 (GND)
BE - W-B
Battery power supply
Always
11 to 14 V
F42-22 (BLW) - F42-14 (GND)
R - W-B
Blower motor control signal
Ignition switch: ON
Pulse generation
(See waveform 4)
Blower switch: LO
F42-29 (TR) - F42-34 (SG-1)
P - SB
Room temperature sensor signal
Ignition switch: ON
1.8 to 2.2 V
Vehicle interior temperature: 25°C
F42-33 (TSD) - F42-14 (GND)
R - W-B
Solar sensor signal
Ignition switch: ON
0.8 to 4.3 V
Solar sensor subject to electric light
F42-34 (SG-1) - Body ground
SB - Body ground
Ground for room temperature sensor
Always
Below 1 Ω
F42-37 (LIN1) - F42-14 (GND)
LG - W-B
LIN communication signal
Ignition switch: ON
Pulse generation
z4-2 (BUSG) - Body ground
-
Ground for BUS IC
Always
Below 1 Ω
z4-3 (BUS) - z4-2 (BUSG)
-
BUS IC control signal
Ignition switch: ON
Pulse generation
z4-4 (BBUS) - z4-2 (BUSG)
-
BUS IC power supply
Always
11 to 14 V
z4-5 (SGA) - Body ground
-
Ground for evaporator temperature sensor
Always
Below 1 Ω
z4-6 (TEA) - z4-5 (SGA)
-
Evaporator temperature sensor signal
Ignition switch: ON
1.4 to 1.8 V
Evaporator temperature: 15°C (59°F)


    E074977E15
  1. Waveform 1: Using an oscilloscope
    Compressor and Pulley Operation Signal 
    Terminal Name
    F42-2 (SOL+) - F42-14 (GND)
    Tester Range
    5 V/DIV, 500 μs/DIV
    Condition
    Engine idling
    Blower switch LO
    A/C switch ON



  2. A086154E01
  3. Waveform 2 (Reference) : Using an oscilloscope
    CAN Communication Signal 
    Terminal Name
    F42-11 (TX+) - F42-14 (GND)
    Tester Range
    1 V/DIV, 10 μs/DIV
    Condition
    Ignition switch ON

    HINT:
    The waveform varies depending on the CAN communication signal.



  4. A086155E06
  5. Waveform 3 (Reference) : Using an oscilloscope
    CAN Communication Signal 
    Terminal Name
    F42-12 (TX-) - F42-14 (GND)
    Tester Range
    1 V/DIV, 10 μs/DIV
    Condition
    Ignition switch ON

    HINT:
    The waveform varies depending on the CAN communication signal.



  6. E103396E15
  7. Waveform 4: Using an oscilloscope.
    Blower Motor Control Signal 
    Terminal Name
    F42-22 (BLW) - F42-14 (GND)
    Tester Range
    1 V/DIV, 500 μs/DIV
    Condition
    Ignition switch ON
    Blower switch LO

    HINT:
    When the blower level is increased, the duty ratio changes accordingly.


CHECK AIR CONDITIONING CONTROL ASSEMBLY
If the result is not as specified, there may be a malfunction in the wire harness.

E167351E03


Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
F40-5 (IG+) - F40-8 (GND)
V - BR
Ignition power supply
Ignition switch: ON
11 to 14 V
F40-3 (LIN1) - F40-8 (GND)
LG - BR
LIN communication signal
Ignition switch: ON
Pulse generation
F40-8 (GND) - Body ground
BR - Body Ground
Ground for air conditioning control assembly
Always
Below 1 Ω