Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (for Built-in Type Yaw Rate Sensor)

DTC    C1361    Short in ABS Motor Fail Safe Relay Circuit

DTC    C146C    Open in ABS Motor Relay Circuit

DTC    C146D    Short in ABS Motor Relay Circuit

for Preparation Click here


DESCRIPTION

The ABS motor relay supplies power to the ABS pump motor. While the ABS is activated, the ECU turns the motor relay on and operates the ABS pump motor.
If the voltage supplied to the motor relay (BM) is below the DTC's detection threshold due to low voltage from the battery or generator, the DTC may be stored.

DTC No.
DTC Detection Condition
Trouble Area
C1361
Immediately after the ignition switch is turned to ON, the relay contact is closed for 4 seconds when the motor fail safe relay is OFF.
  1. ABS NO. 1 fuse
  2. ABS motor fail safe relay circuit
  3. Brake actuator assembly (ABS motor fail safe relay)
C146C
When either of the following is detected:
  1. All of the following conditions continue for 0.12 seconds or more.
    1. The IG1 terminal voltage is between 9.5 and 17.2 V.
    2. While initial check and ABS, BA, TRC or VSC is operating.
    3. Relay contact is open when the relay is ON.
  2. Both of the following conditions continue for 0.12 seconds.
    1. The IG1 terminal voltage is less than 9.5 V.
    2. Relay contact remains open when the relay is ON.
  1. ABS NO. 1 fuse
  2. ABS motor relay circuit
  3. Brake actuator assembly (ABS motor relay)
C146D
When the motor relay is OFF, the motor relay remains closed for 4 seconds or more.
  1. ABS motor relay circuit
  2. Brake actuator assembly (ABS motor relay)

WIRING DIAGRAM


C248758E04


INSPECTION PROCEDURE

NOTICE:
  1. When replacing the brake actuator assembly, perform zero point calibration (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
When C1241 is output together with C146C, C146D and/or C1361 inspect and repair the trouble areas indicated by C1241 first (Click here).

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ABS MOTOR RELAY)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

  1. According to the display on the tester, perform the Active Test.

    ABS/VSC/TRC 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Motor Relay
    ABS motor relay
    Relay OFF/ON
    Operating sound of motor can be heard.
    [Vehicle condition]
    Vehicle stopped

  1. Check the operating sound of the ABS motor relay when operating it with the intelligent tester.

Result 
Result
Proceed to
The operating sound is not heard
A
The operating sound is heard
B


B
Go to step 4
A


2.CHECK TERMINAL VOLTAGE (BM TERMINAL)
  1. Turn the ignition switch off.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Check the connector case and terminals for deformation and corrosion.

    OK:
    No deformation or corrosion.



    C243286E04
  1. Disconnect the skid control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A54-24 (BM) - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid control ECU)

  1. Turn the ignition switch off.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (BM CIRCUIT)
OK


3.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)


    C243286E05
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A54-13 (GND2) - Body ground
    Always
    Below 1 Ω

Text in Illustration 
*a
Front view of wire harness connector
(to Skid control ECU)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND2 CIRCUIT)
OK


4.RECONFIRM DTC

HINT:
These codes are detected when a problem is determined in the skid control ECU (brake actuator assembly).
The solenoid circuits are in the skid control ECU (brake actuator assembly).
Therefore, solenoid circuit inspection and solenoid unit inspection cannot be performed. Be sure to check if any DTCs are output before replacing the skid control ECU (brake actuator assembly).

  1. Clear the DTC (Click here).

  1. Start the engine.

  1. Drive the vehicle at the speed of 20 km/h (12 mph) or more for 30 seconds or more.

  1. Check if the same DTC is recorded (Click here).

Result 
Result
Proceed to
DTC is not output
A
DTC is output
B

HINT:
  1. If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU (brake actuator assembly), with the ignition switch ON and the stop light switch off, the ECU performs self diagnosis of the motor and solenoid circuits.
  2. If the normal system code is output (the trouble code is not output), slightly jiggle the connectors, wire harness, and fuses of the skid control ECU (brake actuator assembly). Make sure that no DTCs are output.
  3. If any DTCs are output while jiggling a connector or wire harness from the brake actuator assembly (skid control ECU (brake actuator assembly)), inspect and repair the connector or wire harness.
  4. The DTCs were probably output due to a bad connection of the connector terminal.



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)