DTC B1830/57 Short in Curtain Shield Squib RH Circuit |
DTC B1831/57 Open in Curtain Shield Squib RH Circuit |
DTC B1832/57 Short to GND in Curtain Shield Squib RH Circuit |
DTC B1833/57 Short to B+ in Curtain Shield Squib RH Circuit |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1830/57 |
|
|
| B1831/57 |
| |
| B1832/57 |
| |
| B1833/57 |
|

| 1.CHECK CONNECTORS |
![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Check that the connectors are properly connected to the curtain shield airbag assembly RH and airbag sensor assembly.
Disconnect the connectors from the curtain shield airbag assembly RH and airbag sensor assembly.
Check that the terminals of the connectors are not damaged.
Check that the floor wire connector (on the curtain shield airbag assembly RH side) is not damaged.
Check that the short spring for the floor wire with the activation prevention mechanism is not deformed or damaged.
| *1 | Curtain Shield Airbag Assembly RH (Curtain Shield Squib RH) |
| *2 | Airbag Sensor Assembly |
| *3 | Floor Wire |
|
| ||||
| OK | |
| 2.CHECK CURTAIN SHIELD AIRBAG ASSEMBLY RH (CURTAIN SHIELD SQUIB RH) |
![]() |
Connect the connector to the airbag sensor assembly.
Connect SST (resistance 2.1 Ω) to connector C.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| *1 | Curtain Shield Airbag Assembly RH (Curtain Shield Squib RH) |
| *2 | Airbag Sensor Assembly |
| *3 | Connector C |
| *a | Front view of wire harness connector (to Curtain Shield Airbag Assembly RH (Curtain Shield Squib RH)) |
|
| ||||
| OK | ||
| ||
| 3.CHECK FLOOR WIRE (CURTAIN SHIELD SQUIB CIRCUIT RH) |
![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Disconnect SST from connector C.
Disconnect the floor wire from the airbag sensor assembly.
Check for a short to B+ in the circuit.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| K28-1 (ICR+) - Body ground | Ignition switch ON | Below 1 V |
| K28-2 (ICR-) - Body ground | Ignition switch ON | Below 1 V |
Check for an open in the circuit.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| K28-1 (ICR+) - K28-2 (ICR-) | Always | Below 1 Ω |
Check for a short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| K28-1 (ICR+) - Body ground | Always | 1 MΩ or higher |
| K28-2 (ICR-) - Body ground | Always | 1 MΩ or higher |
Check for a short in the circuit.
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| K28-1 (ICR+) - K28-2 (ICR-) | Always | 1 MΩ or higher |
| *1 | Curtain Shield Airbag Assembly RH (Curtain Shield Squib RH) |
| *2 | Airbag Sensor Assembly |
| *3 | Floor Wire |
| *4 | Connector C |
| *a | Front view of wire harness connector (to Curtain Shield Airbag Assembly RH (Curtain Shield Squib RH)) |
|
| ||||
| OK | |
| 4.CHECK DTC |
Restore the released activation prevention mechanism of connector B to the original condition.
Connect the connectors to the curtain shield airbag assembly RH and airbag sensor assembly.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||