Home › Vehicle Interior › INTERIOR PANELS / TRIM › LOWER INSTRUMENT PANEL

LOWER INSTRUMENT PANEL > INSTALLATION

for Preparation Click here



1. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY


    B284290E01
  1. Using a nipper, cut off both ends of the runner portion shown in the illustration (When installing a new one).
    Text in Illustration 
    *a
    Runner Portion
    *b
    Cut Off

  1. Engage the 10 guides and install the lower instrument panel.



  1. Install the lower instrument panel with the 6 <B> or <C> bolts, <D> or <E> screw, 2 <F> or <H> or <I> bolts and bolt.


    B284278E01

  1. Connect the clamps and connectors.

  1. Engage the 2 claws and install the DLC3 connector.



2. INSTALL HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
  1. Engage the 3 claws and install the hood lock control lever.



3. INSTALL REAR CONSOLE BOX ASSEMBLY
(Click here)


4. INSTALL AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System)
  1. Connect the connectors and engage the clamp.

  1. Install the cooler hose.

  1. Engage the claw and 7 clips and install the air conditioning control.



5. CONNECT AIR MIX DAMPER CONTROL CABLE SUB-ASSEMBLY (for Manual Air Conditioning System)
  1. Engage the 2 claws and connect the air mix damper control cable.



6. CONNECT AIR INLET DAMPER CONTROL CABLE SUB-ASSEMBLY (for Manual Air Conditioning System)
  1. Engage the 3 claws and connect the air inlet damper control cable.



7. CONNECT DEFROSTER DAMPER CONTROL CABLE SUB-ASSEMBLY (for Manual Air Conditioning System)
  1. Engage the 2 claws and connect the defroster damper control cable.



8. INSTALL AIR CONDITIONING PANEL ASSEMBLY (for Manual Air Conditioning System)
  1. Connect the connector.

  1. Engage the claw and 7 clips and install the air conditioning panel.



9. INSTALL STEREO OPENING COVER WITH BRACKET (w/o Radio Receiver)


    B290382
  1. Align the 2 holes in the radio bracket with the 2 bosses of the instrument panel.

  1. Install the radio stereo opening cover with bracket with the 4 screws.



10. INSTALL RADIO RECEIVER ASSEMBLY WITH BRACKET (w/ Radio Receiver)
  1. Connect the connectors.



    E232539
  1. Align the 2 holes in the radio bracket with the 2 bosses of the instrument panel and engage the 4 clips.

  1. Install the radio receiver assembly with bracket with the 4 screws.



11. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL (w/o Knee Airbag)
  1. for LHD:

    1. Engage the 5 claws and 2 clips and install the instrument panel finish panel.

  1. for RHD:

    1. Engage the 6 claws and 2 clips and install the instrument panel finish panel.



12. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Knee Airbag)
  1. Check that the ignition switch is off.

  1. Check that the cable is disconnected from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



    B287816E01
  1. Connect the airbag connector.
    Text in Illustration 
    *1
    Locking Button

  1. Push in the locking button.

    NOTICE:
    Securely lock the locking button.

  1. Engage the 6 claws and install the lower No. 1 instrument panel airbag assembly.

  1. Install the 4 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



13. INSTALL LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL (for LHD)
  1. Engage the 2 claws and 5 clips and install the instrument panel finish panel.



14. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
  1. Engage the guide and the claw.

  1. Install the instrument panel under cover with the 2 <A> screws.



15. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
  1. Engage the guide and the 3 claws and install the instrument panel under cover.



16. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY


    B284292E01
  1. Engage the 3 guides and 2 hinges in the horizontal direction to install the glove compartment door.
    Text in Illustration 
    *1
    Hinge
    *2
    Guide

    NOTICE:
    Engage the 2 hinges in the horizontal direction, otherwise, installation failure caused by excessive play around the hinges will result.



    B284269
  1. While pushing in the sides of the glove compartment door as indicated by the arrows in the illustration, close the door to engage it to the 2 stoppers.

  1. Engage the claw and connect the glove compartment door stopper.



17. INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY
(Click here)