Home › Power Source / Network · NETWORKING › CAN COMMUNICATION SYSTEM (except Separate Type Yaw Rate Sensor)

CAN COMMUNICATION SYSTEM (except Separate Type Yaw Rate Sensor) > DIAGNOSIS SYSTEM

for Preparation Click here



BUS CHECK (COMMUNICATION MALFUNCTION ECU)
Only CAN communication system DTCs for each ECU can be output to the intelligent tester.


    C128170
  1. Select "Bus Check" from the "System Select" screen on the intelligent tester.



  2. C128171
  3. Select "Communication Malfunction DTC" from the "Bus Check" screen, and then select "Enter".



  4. C128172
  5. Select the system of the DTC to be checked and select "Details".



  6. C128173
  7. CAN communication system DTCs are output.


BUS CHECK (COMMUNICATION BUS CHECK)

HINT:
The ECUs and sensors that are properly connected to the CAN communication system can be displayed using the intelligent tester.



    C128171
  1. Select "Communication Bus Check" from the "Bus Check" screen.

  2. The screen displays the ECUs and sensors that are properly connected to the CAN communication system.

    HINT:
    1. If any properly connected ECUs or sensors are not displayed, there is a communication stop in the system (Click here).

    2. C197127
      The default item displayed in the combo box is "ALL". When checking the ECUs (sensors) connected to each bus, pull down the combo box and select the bus to be checked from the drop-down list. The drop-down list displays "ALL", "V Bus" and the names of the remaining buses.
      Combo Box
      Display Content
      ALL
      All ECUs (sensors) connected to the CAN bus
      V Bus
      ECUs (sensors) connected to the V Bus
      Bus Name
      ECUs (sensors) connected to the selected bus
    3. The connection status (shown below) is indicated by the background color displayed behind the system name.
      ECU (Sensor) on V Bus 
      Background Color
      Connection Status
      White
      Detected normally
      Yellow
      Could not be detected in the past, but is currently detected
      Red
      Detected in the past, but cannot be detected now
      Not displayed
      Has never been detected
      ECU (Sensor) with no Data Monitor History 
      Background Color
      Connection Status
      White
      Detected normally
      Yellow
      Could not be detected in the past, but is currently detected
      Red
      Detected in the past, but cannot be detected now
      Not displayed
      Has never been detected
      ECU (Sensor) with Data Monitor History 
      Background Color
      Connection Status
      White
      Detected normally
      Yellow
      Could not be detected in the past, but is currently detected
      Red
      Detected in the past, but cannot be detected now
      Red
      Has never been detected but has connection history
      Not displayed
      Has never been detected and has no connection history



  3. C128179
  4. "There is no system connected the communication bus." is displayed if there are no ECUs or sensors connected to the CAN bus.


CHECK INSTALLED SYSTEMS (ECUS AND SENSORS) THAT USE CAN COMMUNICATION
  1. Systems (ECUs and sensors) that use CAN communication vary depending on the optional settings of the vehicle. Check which systems (ECUs and sensors) are installed on the vehicle.

    ECU/Sensor Name
    Tester Display
    Installed on
    Air conditioning amplifier assembly
    Air Conditioning Amplifier
    w/ Cooler
    Airbag sensor assembly
    Airbag
    All vehicles
    Combination meter assembly
    Combination Meter
    All vehicles
    ECM
    ECM (Engine)
    All vehicles
    Main body ECU (multiplex network body ECU)
    Main Body
    All vehicles
    Power steering ECU assembly
    Power Steering (EPS)
    All vehicles
    Skid control ECU (brake actuator assembly)
    Skid Control (ABS/VSC/TRAC)
    All vehicles
    Steering angle sensor (spiral cable sub-assembly)
    Spiral cable (Steering Angle Sensor)
    w/ VSC


DTC TABLE BY ECU

HINT:
  1. In the CAN communication system, CAN communication system DTCs stored by the ECU can be output from the ECU by using the intelligent tester.
  2. If CAN communication system DTCs are output, the trouble cannot be determined solely from the DTCs. Perform troubleshooting according to "How to Proceed with Troubleshooting".

  1. ECM

    HINT:
    DTC communication uses the CAN communication system.


    DTC No.
    Detection Item
    U0129
    Lost Communication with Brake System Control Module

  2. MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

    HINT:
    DTC communication uses the CAN communication system.


    DTC No.
    Detection Item
    U0100
    Lost Communication With ECM/PCM "A"
    U0101
    Lost Communication with TCM
    U0151
    Lost Communication With Restraints Control Module
    U0155
    Lost Communication with Instrument Panel Cluster (IPC) Control Module
    U0164
    Lost Communication With HVAC Control Module

  3. SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) (w/ VSC)

    HINT:
    DTC communication uses the CAN communication system.


    DTC No.
    Detection Item
    U0073
    Control Module Communication Bus Off
    U0100
    Lost Communication With ECM/PCM "A"
    U0123
    Lost Communication with Yaw Rate Sensor Module
    U0124
    Lost Communication with Lateral Acceleration Sensor Module
    U0126
    Lost Communication with Steering Angle Sensor Module
    U0142
    Lost Communication with Body Control Module "B"

  4. SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) (w/o VSC)

    HINT:
    DTC communication uses the CAN communication system.


    DTC No.
    Detection Item
    U0073
    Control Module Communication Bus Off
    U0142
    Lost Communication with Body Control Module "B"

  5. POWER STEERING ECU ASSEMBLY

    HINT:
    DTC communication uses the CAN communication system.


    DTC No.
    Detection Item
    U0100
    Lost Communication with ECM/PCM "A"
    U0129
    Lost Communication With Brake System Control Module

  6. COMBINATION METER ASSEMBLY

    HINT:
    DTC communication uses the CAN communication system.


    DTC No.
    Detection Item
    U0100
    Lost Communication with ECM/PCM "A"
    U0129
    Lost Communication with Brake System Control Module
    U0131
    Lost Communication with Power Steering Control Module
    U0151
    Lost Communication with Restraints Control Module

  7. AIR CONDITIONING AMPLIFIER ASSEMBLY (w/ Cooler)

    HINT:
    DTC communication uses the CAN communication system.


    DTC No.
    Detection Item
    U0100
    Lost Communication With ECM/PCM "A"
    U0131
    Lost Communication With Power Steering Control Module
    U0142
    Lost Communication With Body Control Module "B"
    U0155
    Lost Communication With Instrument Panel Cluster (IPC) Control Module

  8. STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY) (w/ VSC)

    HINT:
    The steering angle sensor (spiral cable sub-assembly) is connected to the CAN communication system but CAN communication DTCs are not stored.

  9. AIRBAG SENSOR ASSEMBLY

    HINT:
    The center airbag sensor assembly is connected to the CAN communication system but CAN communication DTCs are not stored.


DTC COMBINATION TABLE

HINT:
  1. ○: Stored.
  2. X: When one side of the branch wire is open, storage may occur.
  3. -: Not stored.
  4. *1: During a communication stop, cannot be stored.


Output from
Output DTC
Detected Communication Stop Mode
V Bus
ECM Communication Stop Mode
ABS and Traction Actuator (Skid Control ECU) Communication Stop Mode
Brake Actuator (Skid Control ECU) Communication Stop Mode
ECM
U0129
○*1
○
○
Skid control ECU (brake actuator assembly) (w/ VSC)
U0073
X
○*1
X
U0100
○
○*1
X
U0123
X
○*1
X
U0124
X
○*1
X
U0126
X
○*1
X
U0142
X
○*1
X
Skid control ECU (brake actuator assembly) (w/o VSC)
U0073
X
X
○*1
U0142
X
X
○*1
Air conditioning amplifier assembly
U0100
○
-
-
U0131
-
-
-
U0142
-
-
-
U0155
-
-
-
Main body ECU (multiplex network body ECU)
U0100
○
-
-
U0101
○
-
-
U0151
-
-
-
U0155
-
-
-
U0164
-
-
-
Power steering ECU assembly
U0100
○
-
-
U0129
-
○
○
Combination meter assembly
U0100
○
-
-
U0129
-
○
○
U0131
-
-
-
U0151
-
-
-

HINT:
  1. ○: Stored.
  2. X: When one side of the branch wire is open, storage may occur.
  3. -: Not stored.
  4. *1: During a communication stop, cannot be stored.


Output from
Output DTC
Detected Communication Stop Mode
V Bus
Air Conditioning Amplifier Communication Stop Mode
Center Airbag Sensor Communication Stop Mode
Main Body ECU Communication Stop Mode
ECM
U0129
-
-
-
Skid control ECU (brake actuator assembly) (w/ VSC)
U0073
X
X
X
U0100
X
X
X
U0123
X
○
X
U0124
X
○
X
U0126
X
X
X
U0142
X
X
○
Skid control ECU (brake actuator assembly) (w/o VSC)
U0073
X
X
X
U0142
X
X
○
Air conditioning amplifier assembly
U0100
○*1
-
-
U0131
○*1
-
-
U0142
○*1
-
○
U0155
○*1
-
-
Main body ECU (multiplex network body ECU)
U0100
-
-
○*1
U0101
-
-
○*1
U0151
-
○
○*1
U0155
-
-
○*1
U0164
○
-
○*1
Power steering ECU assembly
U0100
-
-
-
U0129
-
-
-
Combination meter assembly
U0100
-
-
-
U0129
-
-
-
U0131
-
-
-
U0151
-
○
-

HINT:
  1. ○: Stored.
  2. X: When one side of the branch wire is open, storage may occur.
  3. -: Not stored.
  4. *1: During a communication stop, cannot be stored.


Output from
Output DTC
Detected Communication Stop Mode
V Bus
Power Steering ECU Communication Stop Mode
Steering Angle Sensor Communication Stop Mode
Combination Meter ECU Communication Stop Mode
ECM
U0129
-
-
-
Skid control ECU (brake actuator assembly) (w/ VSC)
U0073
X
X
X
U0100
X
X
X
U0123
X
X
X
U0124
X
X
X
U0126
X
○
X
U0142
X
X
X
Skid control ECU (brake actuator assembly) (w/o VSC)
U0073
X
X
X
U0142
X
X
X
Air conditioning amplifier assembly
U0100
-
-
-
U0131
○
-
-
U0142
-
-
-
U0155
-
-
○
Main body ECU (multiplex network body ECU)
U0100
-
-
-
U0101
-
-
-
U0151
-
-
-
U0155
-
-
○
U0164
-
-
-
Power steering ECU assembly
U0100
○*1
-
-
U0129
○*1
-
-
Combination meter assembly
U0100
-
-
○*1
U0129
-
-
○*1
U0131
○
-
○*1
U0151
-
-
○*1

HINT:
  1. ○: Stored.
  2. X: When one side of the branch wire is open, storage may occur.
  3. -: Not stored.
  4. *1: During a communication stop, cannot be stored.