Home › General › SPECIFICATIONS › U441E AUTOMATIC TRANSMISSION / TRANSAXLE

U441E AUTOMATIC TRANSMISSION / TRANSAXLE > SERVICE DATA



Automatic Transaxle System 
Line pressure (Wheel locked)
AT stall (Throttle valve fully opened)
D position
1087 to 1207 kPa
(11.1 to 12.3 kgf/cm2, 158 to 175 psi)
R position
1423 to 1678 kPa
(14.5 to 17.1 kgf/cm2, 206 to 243 psi)
Engine stall speed
D position
2120 +/-300 rpm
Time lag
N → D position
Less than 1.2 seconds
N → R position
Less than 1.5 seconds
Engine idle speed (A/C off)
N position
650 to 750 rpm
Shift schedule
D position
Throttle valve opening 6%
1 → 2
10 to 15 km/h (6 to 9 mph)
2 → 3
15 to 25 km/h (9 to 16 mph)
3 → 4
30 to 40 km/h (19 to 25 mph)
4 (Lock-up)
70 km/h (43 mph) or more
Throttle valve fully opened
(Reference)
1 → 2
45 to 55 km/h (28 to 34 mph)
2 → 3
85 to 100 km/h (53 to 62 mph)
3 → 4
140 to 155 km/h (87 to 96 mph)
Manual downshift permission speed
→ 2
85 to 100 km/h (53 to 62 mph)
→ 1
40 to 50 km/h (25 to 31 mph)

Speed Sensor 
Transmission revolution sensor resistance
1 - 2
20°C (68°F)
560 to 680 Ω

Transmission Wire 
Transmission wire resistance
1(OT+) - 6(OT-)
10°C (50°F)
6.4 kΩ
110°C (230°F)
0.2 kΩ

Valve Body Assembly 
Shift solenoid valve S1 resistance
Solenoid Connector (S1) - Solenoid Body (S1)
20°C (68°F)
11 to 15 Ω
Shift solenoid valve S2 resistance
Solenoid Connector (S2) - Solenoid Body (S2)
20°C (68°F)
11 to 15 Ω
Shift solenoid valve ST resistance
Solenoid Connector (ST) - Solenoid Body (ST)
20°C (68°F)
11 to 15 Ω
Shift solenoid valve SL resistance
Solenoid Connector (SL) - Solenoid Body (SL)
20°C (68°F)
11 to 15 Ω
Shift solenoid valve SLT resistance
1 - 2
20°C (68°F)
5.1 to 5.5 Ω

Park/Neutral Position Switch 
Park/neutral position switch resistance
4(B) - 5(L)
P and N
Below 1 Ω
Except P and N
10 kΩ or higher
2(RB) - 6(PL)
P
Below 1 Ω
Except P
10 kΩ or higher
1(RL) - 2(RB)
R
Below 1 Ω
Except R
10 kΩ or higher
2(RB) - 9(NL)
N
Below 1 Ω
Except N
10 kΩ or higher
2(RB) - 7(DL)
D and 3
Below 1 Ω
Except D and 3
10 kΩ or higher
2(RB) - 3(2L)
2
Below 1 Ω
Except 2
10 kΩ or higher
2(RB) - 8(LL)
L
Below 1 Ω
Except L
10 kΩ or higher

Shift Lever 
Shift lock control ECU voltage
4 (STP) - 1 (E)
Brake pedal depressed
11 to 14 V
Brake pedal released
Below 1 V
5 (KLS+) - 1 (E)
1. Ignition switch ACC and shift lever in P
Below 1 V
2. Ignition switch ACC and shift lever not in P (Within approx. 1 second)
7.5 to 10.5 V
3. Ignition switch ACC and shift lever not in P (After approx. 1 second)
6 to 9 V
6 (ACC) - 1 (E)
Ignition switch ACC
11 to 14 V
Ignition switch ON
11 to 14 V
Ignition switch off
Below 1 V
8 (IG) - 1 (E)
Ignition switch ON
11 to 14 V
Ignition switch off
Below 1 V
Shift lock control ECU resistance
1 (E) - Body ground
When battery voltage not applied
Below 1 Ω
Transmission control switch resistance
1 (NSSD) - 2 (AT3)
3 and 2
Below 1 Ω
Except 3 and 2
10 kΩ or higher
1 (NSSD) - 3 (ATD)
Except 3 and 2
Below 1 Ω
3 and 2
10 kΩ or higher
Shift lock solenoid resistance
4 (P) - 3 (E2)
P
10 kΩ or higher
Except P
Below 1 Ω
1 (SLS+) - 2 (SLS-)
When battery voltage not applied
112 Ω

Differential Oil Seal 
No. 2 transaxle case oil seal drive in depth
Standard
2.6 to 3.6 mm (0.103 to 0.141 in.)
Transaxle case oil seal drive in depth
Standard
2.6 to 3.6 mm (0.103 to 0.141 in.)

Automatic Transaxle Unit 
Input shaft end play
Standard
0.3 to 0.9 mm (0.012 to 0.035 in.)
2nd brake piston return spring free length
Standard
15.85 mm (0.6240 in.)
1st and reverse brake return spring free length
Standard
21.71 mm (0.85472 in.)
Direct clutch return spring free length
Standard
36 mm (1.42 in.)
Overdrive brake return spring free length
Standard
18.99 mm (0.748 in.)
Forward clutch return spring free length
Standard
24.04 mm (0.9465 in.)
Rear transaxle cover inside diameter
Standard
13.94 to 13.96 mm (0.549 to 0.550 in.)
Tapered roller bearing preload
New
0.78 to 1.37 N*m (8.0 to 13.9 kgf*cm, 6.9 to 12.2 in.*lbf)
Used
0.39 to 0.69 N*m (4.0 to 7.0 kgf*cm, 3.5 to 6.1 in.*lbf)
Transaxle case side adjusting shim thickness
Mark A
1.80 mm (0.0709 in.)
Mark B
1.85 mm (0.0728 in.)
Mark C
1.90 mm (0.0748 in.)
Mark D
1.95 mm (0.0768 in.)
Mark E
2.00 mm (0.0787 in.)
Mark F
2.05 mm (0.0807 in.)
Mark G
2.08 mm (0.0819 in.)
Mark H
2.11 mm (0.0831 in.)
Mark J
2.14 mm (0.0843 in.)
Mark K
2.17 mm (0.0854 in.)
Mark L
2.20 mm (0.0866 in.)
Mark M
2.23 mm (0.0878 in.)
Mark N
2.26 mm (0.0890 in.)
Mark P
2.29 mm (0.0902 in.)
Mark Q
2.32 mm (0.0913 in.)
Mark R
2.35 mm (0.0925 in.)
Mark S
2.40 mm (0.0945 in.)
Mark T
2.45 mm (0.0965 in.)
Mark U
2.50 mm (0.0984 in.)
Mark V
2.55 mm (0.1004 in.)
Mark W
2.60 mm (0.1024 in.)
Mark X
2.65 mm (0.1043 in.)
Mark Y
2.70 mm (0.1063 in.)
Manual valve lever shaft oil seal drive in depth
Standard
0.75 to 1.25 mm (0.030 to 0.049 in.)
1st and reverse brake piston stroke
Standard
0.791 to 1.489 mm (0.031 to 0.057 in.)
Counter drive gear bearing preload
Standard
0.05 to 0.35 N*m (0.5 to 3.5 kgf*cm, 0.45 to 3.09 in.*lbf)
Reverse clutch pack clearance
Standard
0.40 to 1.00 mm (0.0157 to 0.0394 in.)
Reverse clutch flange thickness
Mark 1
3.0 mm (0.118 in.)
Mark 2
3.2 mm (0.126 in.)
Mark 3
3.4 mm (0.135 in.)
Mark 4
3.6 mm (0.142 in.)
Front clutch pack clearance
Standard
1.3 to 1.5 mm (0.0512 to 0.0591 in.)
Front clutch flange thickness
Mark 1
3.0 mm (0.118 in.)
Mark 2
3.2 mm (0.126 in.)
Mark 3
3.4 mm (0.135 in.)
Mark 4
3.6 mm (0.142 in.)
2nd coast and overdrive brake piston clearance
Standard
0.65 to 1.05 mm (0.0256 to 0.0413 in.)
Brake flange thickness
Mark 0
3.0 mm (0.118 in.)
(Piston stroke value)
0.738 to 0.949 (0.02905 to 0.03736)
Mark 1
3.2 mm (0.126 in.)
(Piston stroke value)
0.950 to 1.149 (0.03740 to 0.04524)
Mark 2
3.4 mm (0.134 in.)
(Piston stroke value)
1.150 to 1.349 (0.04528 to 0.05311)
Mark 3
3.6 mm (0.142 in.)
(Piston stroke value)
1.350 to 1.549 (0.05315 to 0.06098)
Mark 4
3.8 mm (0.150 in.)
(Piston stroke value)
1.550 to 1.702 (0.06102 to 0.06701)
Direct clutch piston stroke
Standard
0.4 to 0.7 mm (0.0157 to 0.0276 in.)
Direct clutch flange thickness
Mark 1
3.0 mm (0.118 in.)
Mark 2
3.2 mm (0.126 in.)
Mark 3
3.4 mm (0.135 in.)
No. 2 transaxle case oil seal drive in depth
Standard
2.6 to 3.6 mm (0.103 to 0.141 in.)
Transaxle case oil seal drive in depth
Standard
2.6 to 3.6 mm (0.103 to 0.141 in.)

Torque Converter and Drive Plate 
Drive plate runout
Maximum
0.30 mm (0.0118 in.)

Oil Pump 
Stator shaft inside diameter
Standard
18.424 to 18.449 mm (0.725 to 0.726 in.)
Maximum
18.449 mm (0.726 in.)
Front oil pump body inside diameter
Standard
38.113 to 38.138 mm (1.500 to 1.501 in.)
Maximum
38.138 mm (1.501 in.)
Oil pump clearance
(Driven gear to drive gear)
Standard
0.07 to 0.15 mm (0.00276 to 0.00591 in.)
Maximum
0.15 mm (0.00591 in.)
Oil pump clearance
(Driven gear to oil pump body)
Standard
0.10 to 0.17 mm (0.00394 to 0.00669 in.)
Maximum
0.17 mm (0.00669 in.)
Oil pump clearance
(Side clearance)
Standard
0.02 to 0.05 mm (0.000787 to 0.001969 in.)
Maximum
0.05 mm (0.001969 in.)
Front oil pump oil seal drive in depth
Standard
-0.085 to 0.015 mm (-0.0335 to 0.00591 in.)

Differential Case 
Side gear back lash
Standard
0.05 to 0.20 mm (0.0020 to 0.0079 in.)
Side gear thrust washer thickness
-
1.50 mm (0.0589 in.)
-
1.55 mm (0.0609 in.)
-
1.60 mm (0.0629 in.)
-
1.65 mm (0.0649 in.)
-
1.70 mm (0.0669 in.)
-
1.75 mm (0.0689 in.)
Drive pinion plug drive in depth
Standard
2.3 to 2.35 mm (0.090 to 0.093 in.)