SEAT BELT WARNING SYSTEM > OPERATION CHECK |
| INSPECT FRONT SEAT BELT WARNING LIGHT (DRIVER SIDE) |
Turn the ignition switch to ON.
When the driver seat belt is not fastened without the front passenger seat occupied, check that the front seat belt warning light in the combination meter assembly blinks.
When the driver seat belt is fastened, check that the front seat belt warning light in the combination meter turns off.
| INSPECT FRONT SEAT BELT WARNING LIGHT (FRONT PASSENGER SIDE) |
Turn the ignition switch to ON.
When the driver seat belt is fastened and the front passenger side seat belt is not fastened with the front passenger seat occupied, check that the front seat belt warning light in the combination meter assembly blinks.
When the front seat belt is fastened with the front passenger seat occupied, check that the front seat belt warning light in the combination meter assembly turns off.
| INSPECT SEAT BELT WARNING BUZZER (for 5 Door) |
Lift up the vehicle using a swing arm type lift (Click here).
Turn the ignition switch to ON.
Place a weight of 20 kg (44.0 lb) on the front passenger seat.
Open and close a front door (the front door courtesy light switch turns on and off).
for Australia:
When the vehicle is driven at approximately 20 km/h (12.5 mph) or more while the driver or front passenger is not fastened, check that the buzzer in the combination meter sounds at an interval of 1.2 seconds for 30 seconds, and then sounds at an interval of 0.4 seconds for 90 seconds.
for G.C.C.:
When the vehicle is driven at 20 km/h (12 mph) or more with the front passenger seat occupied and the driver or front passenger seat belt not fastened, the seat belt warning buzzer in the combination meter assembly sounds once. When 30 seconds have passed after the buzzer sounded, the seat belt warning buzzer in the combination meter assembly sounds at an interval of 1.2 seconds for 9.6 seconds. After that, the seat belt warning buzzer in the combination meter assembly sounds at an interval of 0.4 seconds for 20 seconds.
for Australia:
Check that the buzzer stops 2 minutes after the buzzer starts sounding.
for G.C.C.:
After previous step, check that the buzzer sounds at an interval of 0.4 seconds for 20 seconds.
After the buzzer stops, turn the ignition switch off and then start the engine again. Then drive the vehicle at approximately 20 km/h (12.5 mph) or more while the driver or front passenger seat belt is not fastened, and check that the buzzer sounds again.
After the buzzer stops, fasten the driver and front passenger seat belts. Drive the vehicle at approximately 20 km/h (12.5 mph) or more and unfasten the driver or front passenger seat belt, and then check that the buzzer sounds again.
After the buzzer stops, move the shift lever to R, and then move it to D. Drive the vehicle at approximately 20 km/h (12.5 mph) or more, and then check that the buzzer sounds again.
| INSPECT SEAT BELT WARNING BUZZER (for 3 Door) |
Lift up the vehicle using a swing arm type lift (Click here).
Turn the ignition switch to ON.
Place a weight of 20 kg (44.0 lb) on the front passenger seat.
Open and close a front door (the front door courtesy light switch turns on and off).
for Australia:
When the vehicle is driven at approximately 20 km/h (12.5 mph) or more while the driver or front passenger is not fastened, check that the buzzer in the combination meter sounds at an interval of 1.2 seconds for 30 seconds, and then sounds at an interval of 0.4 seconds for 90 seconds.
for G.C.C.:
When the vehicle is driven at 20 km/h (12 mph) or more with the front passenger seat occupied and the driver or front passenger seat belt not fastened, the seat belt warning buzzer in the combination meter assembly sounds once. When 30 seconds have passed after the buzzer sounded, the seat belt warning buzzer in the combination meter assembly sounds at an interval of 1.2 seconds for 9.6 seconds. After that, the seat belt warning buzzer in the combination meter assembly sounds at an interval of 0.4 seconds for 20 seconds.
for Australia:
Check that the buzzer stops 2 minutes after the buzzer starts sounding.
for G.C.C.:
After previous step, check that the buzzer sounds at an interval of 0.4 seconds for 20 seconds.
After the buzzer stops, turn the ignition switch off and then start the engine again. Then drive the vehicle at approximately 20 km/h (12.5 mph) or more while the driver or front passenger seat belt is not fastened, and check that the buzzer sounds again.
After the buzzer stops, fasten the driver and front passenger seat belts. Drive the vehicle at approximately 20 km/h (12.5 mph) or more and unfasten the driver or front passenger seat belt, and then check that the buzzer sounds again.
After the buzzer stops, move the shift lever to R, and then move it to D. Drive the vehicle at approximately 20 km/h (12.5 mph) or more, and then check that the buzzer sounds again.