Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT ASSEMBLY

HEADLIGHT ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL HEADLIGHT ASSEMBLY
  1. Connect the connectors.

  1. Install the headlight assembly with the 3 screws.



2. INSTALL FRONT BUMPER COVER (for Sport Package)
(Click here)


3. INSTALL FRONT BUMPER COVER (except Sport Package)
(Click here)


4. PREPARE VEHICLE FOR HEADLIGHT AIMING ADJUSTMENT
  1. Prepare the vehicle:

    1. Ensure that there is no damage or deformation of the body around the headlights.
    2. Fill the fuel tank.
    3. Fill the oil to the specified level.
    4. Fill the coolant to the specified level.
    5. Inflate the tires to the appropriate pressure.
    6. Place the spare tire, tools and jack in their original positions.
    7. Unload the trunk.
    8. Sit a person of average weight (75 kg, 165 lb) in the driver seat.



5. PREPARE FOR HEADLIGHT AIMING


E229133E01
Text in Illustration 
*a
90°
*b
25 or 3 m (82 or 9.84 ft.)
  1. Prepare the vehicle in accordance with the following conditions:

    1. Place the vehicle in a location that is dark enough to clearly observe the cutoff line. The cutoff line is a distinct line, below which light from the headlights can be observed and above which it cannot.
    2. Place the vehicle at a 90° angle to the wall.
    3. Keep a 25 m (82 ft.) distance between the center of the headlight bulb and the wall.
    4. Place the vehicle on a level surface.
    5. Bounce the vehicle up and down to settle the suspension.

      HINT:
      A distance of 25 m (82 ft.) between the vehicle (the center of the headlight bulb) and the wall is necessary for proper aim adjustment. If unable to secure a distance of 25 m (82 ft.), set a distance of exactly 3 m (9.84 ft.) to check and adjust the headlight aim (Since the target zone changes depending on the distance, follow the instructions shown in the illustration.).

  1. Prepare a piece of thick white paper (approximately 2 m (6.6 ft.) high x 4 m (13.1 ft.) wide) to use as a screen.

  1. Draw a vertical line down the center of the screen (V line).



  1. Set the screen, as shown in the illustration.


    E229134E02


    Text in Illustration 
    *a
    Aligning distance 25 m (82 ft.)
    *b
    Aligning distance 3 m (9.84 ft.)
    *c
    V RH Line
    *d
    V LH Line
    *e
    V Line
    *f
    H Line
    *g
    90°
    *h
    25 m (82 ft.)
    *i
    3 m (9.84 ft.)
    -
    -

    HINT:
    1. Stand the screen perpendicular to the ground.
    2. Align the V line on the screen with the center of the vehicle.



    I033423E25
  1. Draw base lines (H line, V LH and V RH lines) on the screen, as shown in the illustration.
    Text in Illustration 
    *a
    V LH Line
    *b
    V Line
    *c
    V RH Line
    *d
    H Line
    *e
    Ground

    HINT:
    1. The base lines differ for "low beam inspection" and "high beam inspection".
    2. Mark the headlight bulb center marks on the screen. If the center mark cannot be observed on the headlight, use the center of the headlight bulb.


    1. H Line (Headlight height):
      Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the headlight bulb center marks of the low-beam headlights.

    2. V LH Line and V RH Line (Center mark positions of left-hand (LH) and right-hand (RH) headlights):
      Draw two vertical lines so that they intersect the H line at each center mark (aligned with the center of the low-beam headlight bulbs).



6. INSPECT HEADLIGHT AIMING
  1. Cover the headlight on the opposite side or disconnect its connector, to prevent light from the headlight not being inspected from affecting the headlight aiming inspection.

    NOTICE:
    Do not keep the headlight covered for more than 3 minutes. The headlight lens is made of synthetic resin, and may easily melt or be damaged due to heat.

    HINT:
    When checking the aim of the high beam, cover the low beam or disconnect the connector.

  1. Start the engine.

    HINT:
    Engine speed must be 1500 rpm or more.



  1. Turn on the headlight and make sure that the cutoff line falls within the specified area, as shown in the illustration.


    E235056E01


    Text in Illustration 
    *a
    Aligning distance 25 m (82 ft.)
    *b
    Aligning distance 3 m (9.84 ft.)
    *c
    Low beam
    *d
    High beam
    *e
    V RH Line, V LH Line
    *f
    H Line
    *g
    Cutoff Line
    *h
    83 mm (3.27 in.)
    *i
    249 mm (9.80 in.)
    *j
    375 mm (14.76 in.)
    *k
    30 mm (1.18 in.)
    *l
    10 mm (0.39 in.)
    *m
    45 mm (1.77 in.)
    *n
    175 mm (6.89 in.)
    *o
    21 mm (0.83 in.)
    -
    -

    HINT:
    1. Since the low beam light and the high beam light are a unit, if the aim on one is correct, the other should also be correct. However, check both beams just to make sure.
    2. If the alignment distance is 25 m (82 ft.):
      The low beam cutoff line should be between 83 mm (3.27 in.) and 375 mm (14.76 in.) below the H line as well as 249 mm (9.80 in.) left or right of the V line.
    3. If the alignment distance is 3 m (9.84 ft.):
      The low beam cutoff line should be between 10 mm (0.39 in.) and 45 mm (1.77 in.) below the H line as well as 30 mm (1.18 in.) left or right of the V line.
    4. If the alignment distance is 25 m (82 ft.):
      The high beam center of intensity should be within 249 mm (9.80 in.) above or below the H line as well as 249 mm (9.80 in.) left or right of the V line.
    5. If the alignment distance is 3 m (9.84 ft.):
      The high beam center of intensity should be within 30 mm (1.18 in.) above or below the H line as well as 30 mm (1.18 in.) left or right of the V line.



7. ADJUST HEADLIGHT AIMING


E228376E01
Text in Illustration 
*1
Aiming Screw A
*2
Aiming Screw B
  1. Adjust the aiming vertically:
    Adjust the headlight aim to within the specified range by turning aiming screw A with a screwdriver.

    HINT:
    The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it and then retighten it, so that the final turn of the screw is in the clockwise direction.

  1. Adjust the aiming horizontally:
    Adjust the headlight aim to within the specified range by turning aiming screw B with a screwdriver.

    HINT:
    The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it and then retighten it, so that the final turn of the screw is in the clockwise direction.



8. PREPARE VEHICLE FOR FOG LIGHT AIMING ADJUSTMENT (w/ Fog Light)
  1. Prepare the vehicle:

    1. Ensure that there is no damage or deformation of the body around the fog lights.
    2. Fill the fuel tank.
    3. Fill the oil to the specified level.
    4. Fill the coolant to the specified level.
    5. Inflate the tires to the appropriate pressure.
    6. Place the spare tire, tools and jack in their original positions.
    7. Unload the trunk.
    8. Sit a person of average weight (75 kg, 165 lb) in the driver seat.



9. PREPARE FOR FOG LIGHT AIMING (w/ Fog Light)


E229135E01
Text in Illustration 
*a
90°
*b
25 or 3 m (82 or 9.84 ft.)
  1. Prepare the vehicle in accordance with the following conditions:

    1. Place the vehicle in a location that is dark enough to clearly observe the cutoff line. The cutoff line is a distinct line, below which light from the fog lights can be observed and above which it cannot.
    2. Place the vehicle at a 90° angle to the wall.
    3. Keep a 25 m (82 ft.) distance between the center of the fog light bulb and the wall.
    4. Place the vehicle on a level surface.
    5. Bounce the vehicle up and down to settle the suspension.

    HINT:
    A distance of 25 m (82 ft.) between the vehicle (center of the fog light bulb) and the wall is necessary for proper aim adjustment. If unable to secure a distance of 25 m (82 ft.), secure a distance of exactly 3 m (9.84 ft.) to check and adjust the fog light aim (Since the target zone will change with the distance, follow the instructions shown in the illustration.).

  1. Prepare a piece of thick white paper (approximately 2 m (6.6 ft.) (high) x 4 m (13.1 ft.) (wide)), to use as a screen.

  1. Draw a vertical line down the center of the screen (V line).



  1. Set the screen as shown in the illustration.

    HINT:
    1. Stand the screen perpendicular to the ground.
    2. Align the V line on the screen with the center of the vehicle.



    E229136E03


    Text in Illustration 
    *a
    Aligning distance 25 m (82 ft.)
    *b
    Aligning distance 3 m (9.84 ft.)
    *c
    V RH Line
    *d
    V LH Line
    *e
    H Line
    *f
    25 m (82 ft.)
    *g
    3 m (9.84 ft.)
    *h
    90°
    *i
    V Line
    -
    -



    I033423E24
  1. Draw base lines (H line, V LH, V RH lines) on the screen as shown in the illustration.
    Text in Illustration 
    *a
    V LH Line
    *b
    V Line
    *c
    V RH Line
    *d
    H Line
    *e
    Ground

    HINT:
    Mark the fog light bulb center marks on the screen. If the center mark cannot be observed on the fog light, use the center of the fog light bulb or the manufacturer's name marked on the fog light as the center mark.


    1. H Line (Fog light height):
      Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the fog light bulb center marks of the fog lights.

    2. V LH Line and V RH Line (Center mark positions of left-hand (LH) and right-hand (RH) fog lights):
      Draw two vertical lines so that they intersect the H line at each center mark.



10. INSPECT FOG LIGHT AIMING (w/ Fog Light)
  1. Cover the fog light or disconnect the connector of the fog light on the opposite side to prevent light from the fog light not being inspected from affecting fog light aiming inspection.

    NOTICE:
    Do not keep the fog light covered for more than 3 minutes. The fog light is made with plastic components, which may melt or be damaged due to excessive heat.

  1. Start the engine.

    HINT:
    Engine speed must be 1500 rpm or more.



  1. Turn on the fog light and make sure that the cutoff line falls within the specified area, as shown in the illustration.


    I041221E51


    Text in Illustration 
    *a
    Aligning distance 25 m (82 ft.)
    *b
    Aligning distance 3 m (9.84 ft.)
    *c
    V LH Line
    *d
    V RH Line
    *e
    H Line
    *f
    433 mm (17.06 in.)
    *g
    52 mm (2.04 in.)
    *h
    Hot Zone

    HINT:
    1. If the alignment distance is 25 m (82 ft.):
      The upper edge of the hot zone for the fog light should be 433 mm (17.06 in.) below the H line.
    2. If the alignment distance is 3 m (9.84 ft.):
      The upper edge of the hot zone for the fog light should be 52 mm (2.04 in.) below the H line.



11. ADJUST FOG LIGHT AIMING (w/ Fog Light)


    E107962
  1. Adjust the fog light aim to within the specified range by turning the aiming screw with a screwdriver.

    NOTICE:
    The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it and then retighten it, so that the final turn of the screw is in the clockwise direction.