Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT BUMPER (except Sport Package)

FRONT BUMPER (except Sport Package) > REASSEMBLY

for Preparation Click here



1. INSTALL FRONT BUMPER ENERGY ABSORBER SUB-ASSEMBLY (w/ Front Bumper Lower Absorber)


    B271837
  1. Engage the 3 hooks and install the front bumper energy absorber.



    B271836
  1. Install the 6 screws, the 6 clips and grommet.



2. INSTALL ENGINE UNDER COVER RH (w/ Front Bumper Lower Absorber)


3. INSTALL ENGINE UNDER COVER LH (w/ Front Bumper Lower Absorber)


4. INSTALL FRONT SIDE MEMBER BRACKET SUB-ASSEMBLY LH


    B271835
  1. Engage the 2 guides and install the front side member bracket.

  1. Tighten the 4 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



5. INSTALL FRONT SIDE MEMBER BRACKET SUB-ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



6. INSTALL WINDSHIELD WASHER JAR ASSEMBLY


    B288481
  1. Install the windshield washer jar with the bolt.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



7. INSTALL FRONT NO. 1 BUMPER STONE DEFLECTOR BRACKET


    B271834
  1. Install the front No. 1 bumper stone deflector bracket with the 2 nuts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    HINT:
    Use the same procedure as for the opposite side.



8. INSTALL FRONT BUMPER REINFORCEMENT


    B271833
  1. Install the front bumper reinforcement with the 4 nuts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Tighten the 6 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



    B271832
  1. Engage the 2 clamps and install the wire harness.



9. INSTALL FRONT BUMPER ENERGY ABSORBER (w/ Energy Absorber)


    B288635
  1. Engage the 2 guides and install the front bumper energy absorber.



10. INSTALL NO. 2 RADIATOR SIDE AIR SEAL (w/ Energy Absorber)


    B271829
  1. Engage the 2 claws and install the radiator side air seal.



11. INSTALL NO. 1 RADIATOR SIDE AIR SEAL (w/ Energy Absorber)

HINT:
Use the same procedure as for the No. 2 side.



12. INSTALL NO. 2 RADIATOR SIDE AIR SEAL (w/o Energy Absorber)


    B288477
  1. Engage the 2 claws and install the radiator side air seal.



13. INSTALL NO. 1 RADIATOR SIDE AIR SEAL (w/o Energy Absorber)

HINT:
Use the same procedure as for the No. 2 side.



14. INSTALL RADIATOR SUPPORT EXTENSION LH (w/ Energy Absorber)


    B273105
  1. Engage the 2 claws and install the radiator support extension.



15. INSTALL RADIATOR SUPPORT EXTENSION RH (w/ Energy Absorber)

HINT:
Use the same procedure as for the LH side.



16. INSTALL RADIATOR SUPPORT EXTENSION LH (w/o Energy Absorber)


    B288478
  1. Engage the 2 claws and install the radiator support extension.



17. INSTALL RADIATOR SUPPORT EXTENSION RH (w/o Energy Absorber)

HINT:
Use the same procedure as for the No. 2 side.



18. INSTALL THERMISTOR ASSEMBLY


    B271830
  1. Engage the 2 clamps and install the thermistor.



19. INSTALL FRONT BUMPER SIDE RETAINER LH


    B271827
  1. Engage the 2 claws and install the front bumper side retainer.



20. INSTALL FRONT BUMPER SIDE RETAINER RH

HINT:
Use the same procedure as for the LH side.



21. INSTALL HEADLIGHT ASSEMBLY LH
  1. Connect the connectors.

  1. Install the headlight assembly with the 3 screws.



22. INSTALL HEADLIGHT ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



23. INSTALL FOG LIGHT COVER LH


    B271825
  1. Engage the 5 claws and install the fog light cover.



24. INSTALL FOG LIGHT COVER RH

HINT:
Use the same procedure as for the LH side.



25. INSTALL FOG LIGHT ASSEMBLY LH (w/ Fog Light)
  1. Engage the guide to install the fog light assembly.

  1. Install the 2 screws.

  1. Connect the connector.



26. INSTALL FOG LIGHT ASSEMBLY RH (w/ Fog Light)

HINT:
Use the same procedure as for the LH side.



27. INSTALL LOWER NO. 1 RADIATOR GRILLE


    B288476
  1. Engage the 14 claws and install the lower No. 1 radiator grille.



28. INSTALL FRONT BUMPER HOLE COVER


    B271823
  1. Engage the 3 claws and install the front bumper hole cover.



29. INSTALL FRONT BUMPER LOWER COVER


    B271822
  1. Engage the 3 claws and install the front bumper lower cover.



30. INSTALL RADIATOR GRILLE (OR FRONT PANEL) EMBLEM


    B283029
  1. Engage the 2 guides, 4 claws and install the radiator grille (or front panel) emblem.



31. INSTALL RADIATOR GRILLE


    B271820
  1. Engage the 14 claws and install the radiator grille.



    B271818
  1. Install the 3 clips.



32. INSTALL RADIATOR GRILLE SIDE MOULDING LH


    B271819
  1. Engage the 4 claws and install the radiator grille side moulding.



33. INSTALL RADIATOR GRILLE SIDE MOULDING RH

HINT:
Use the same procedure as for the LH side.



34. INSTALL HOOD TO FRONT END PANEL SEAL
  1. Clean the attachment surface.

    1. Using an infrared light, heat the double-sided adhesive tape remaining on the front bumper cover.

      HINT:
      Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.

    2. Using a piece of cloth, rub the remaining double-sided adhesive tape off the front bumper cover while it is hot from the infrared light.

      NOTICE:
      Installing the hood to front end panel seal with any double-sided tape remaining on the front bumper cover may cause adhesion failure. Therefore, completely remove the double-sided tape.

    3. Using a non-residue solvent, clean the attachment surface.



    B283047
  1. Install a new hood to front end panel seal onto the front bumper cover, as shown in the illustration.

    NOTICE:
    Thoroughly press the hood to front end panel seal to ensure that it adheres.



    B271817
  1. Install the 4 clips.