Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR

FRONT DOOR > REASSEMBLY

for Preparation Click here



1. APPLY BODY GREASE


2. INSTALL NO. 1 BLACK OUT TAPE (for 5 Door)

HINT:
Use the same procedure as for the LH side



3. INSTALL FRONT DOOR PANEL CUSHION


    B271614
  1. Install the 2 cushions onto the door panel.



4. INSTALL FRONT DOOR WEATHERSTRIP (for 5 Door)


    B271613
  1. Engage the 29 clips and install the front door weatherstrip.

  1. Engage the clip.



5. INSTALL FRONT DOOR WEATHERSTRIP (for 3 Door)


    B284595
  1. Engage the 32 clips and install the front door weatherstrip.

  1. Engage the clip.



6. INSTALL FRONT DOOR CHECK ASSEMBLY
  1. Apply MP grease to the sliding areas of the front door check.



    B271610
  1. Install the front door check onto the door panel with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Apply adhesive to the threads of the bolt.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Install the front door check onto the body panel with the bolt.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



7. INSTALL FRONT DOOR LOCK OPEN ROD


    B268986E01
  1. Install the front door lock open rod as indicated by the arrows in the order shown in the illustration.
    Text in Illustration 
    *1
    Snap



8. INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY
  1. Apply MP grease to the sliding areas of the front door outside handle frame.



    B271622E01
  1. Slide the front door outside handle frame to install it.
    Text in Illustration 
    *1
    Grommet

  1. Engage the grommet and 2 claws.



    B271625
  1. Using a "TORX" socket wrench T30, install the front door outside handle frame with the screw.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }



9. INSTALL FRONT DOOR OUTSIDE HANDLE REAR PAD


    B271620
  1. Engage the 2 claws and install the front door outside handle rear pad.



10. INSTALL FRONT DOOR OUTSIDE HANDLE FRONT PAD


    B271619
  1. Engage the 3 claws and install the front door outside handle front pad.



11. INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY


    B271618
  1. Pushing the front door outside handle in the direction of the arrow mark shown in the illustration, install the front door outside handle.



12. INSTALL FRONT DOOR LOCK ASSEMBLY (w/ Power Door Lock)

NOTICE:
  1. If reusing the front door lock assembly that has been removed, replace the door lock wire harness seal with a new seal.
  2. Make sure that no grease or dirt adheres to the door lock wire harness seal surface.
  3. Reusing the door lock wire harness seal or using a damaged door lock wire harness seal may cause water intrusion to the connection. This may result in a malfunction of the front door lock assembly.

  1. Apply MP grease to the sliding parts of the front door lock.

  1. Install the door lock wire harness seal to the front door lock.



    E221615E01
  1. Insert the front door lock open rod to the front door lock.
    Text in Illustration 
    *1
    Front Door Lock Open Rod
    V100135
    Slide Direction

    HINT:
    Make sure that the front door lock open rod is securely connected to the front door lock assembly.

  1. Using a "TORX" socket wrench T30, install the front door lock with the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the connector.



13. INSTALL FRONT DOOR LOCK ASSEMBLY (w/o Power Door Lock)

NOTICE:
  1. If reusing the front door lock assembly that has been removed, replace the door lock wire harness seal with a new seal.
  2. Make sure that no grease or dirt adheres to the door lock wire harness seal surface.
  3. Reusing the door lock wire harness seal or using a damaged door lock wire harness seal may cause water intrusion to the connection. This may result in a malfunction of the front door lock assembly.

  1. Apply MP grease to the sliding parts of the front door lock.

  1. Install the door lock wire harness seal to the front door lock.



    E221615E01
  1. Insert the front door lock open rod to the front door lock.
    Text in Illustration 
    *1
    Front Door Lock Open Rod
    V100135
    Slide Direction

    HINT:
    Make sure that the front door lock open rod is securely connected to the front door lock assembly.

  1. Using a "TORX" socket wrench T30, install the front door lock with the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



14. INSTALL FRONT DOOR OUTSIDE HANDLE COVER


    B271703
  1. Engage the 2 guides.

  1. Engage the claw and install the front door outside handle cover.



    B271615
  1. Temporarily install the front door outside handle cover.

  1. Using a "TORX" socket wrench T30, install the front door outside handle cover.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

  1. Install the hole plug.



15. INSTALL FRONT DOOR FIX WINDOW WEATHERSTRIP
  1. Install the front door fix window glass onto the front door fix window weatherstrip.



    B271612
  1. Slide the front door fix window weatherstrip, in the direction indicated by the arrow in the illustration, to install it.



16. INSTALL FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY


    B271609
  1. Install the front door front lower frame with the 2 bolts and screw.

    Torque:
    Bolt:
    6.2 N*m{ 63 kgf*cm , 55 in.*lbf }



17. INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY


    B271608
  1. Engage the guide.

  1. Install the front door rear lower frame with the bolt.

    Torque:
    6.2 N*m{ 63 kgf*cm , 55 in.*lbf }



18. INSTALL FRONT DOOR GLASS RUN


    B271607
  1. Install the front door glass run.



19. INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY (w/ Power Window)
  1. Apply MP grease to the sliding parts of the front door window regulator.

  1. Install the temporary bolt.



    B271605E02
  1. Insert the front door window regulator into the door panel. Use the temporary bolt to hang the front door window regulator on the door panel.
    Text in Illustration 
    *1
    Temporary Bolt

  1. Tighten the 3 bolts and the temporary bolt in the order shown in the illustration.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Install the front door window regulator with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the connector.



20. INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY (w/o Power Window)
  1. Apply MP grease to the sliding parts of the front door window regulator.

  1. Install the temporary bolt.



    B284589E02
  1. Insert the front door window regulator into the door panel. Use the temporary bolt to hang the front door window regulator on the door panel.
    Text in Illustration 
    *1
    Temporary Bolt

  1. Tighten the 2 bolts and temporary bolt in the order shown in the illustration.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Install the front door window regulator with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



21. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY
  1. Connect the cable to the negative (-) battery terminal.

  1. Connect the power window regulator master switch and move the front door glass so that the door glass bolt holes can be seen.

  1. Disconnect the cable from the negative (-) battery terminal and the power window regulator master switch.



    B271604E01
  1. Insert the front door glass into the front door panel along the front door glass run as indicated by the arrows in the order shown in the illustration.

    NOTICE:
    Do not damage the front door glass.



    B271602
  1. Install the front door glass with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



    B271601
  1. Install the front door service hole cover.



22. INSTALL FRONT DOOR SERVICE HOLE COVER (for 5 Door)
  1. Apply butyl tape to the front door panel.

  1. Pass the front door lock remote control cable, front door inside locking cable and each connector through a new front door service hole cover.



    B271702E01
  1. Install a new front door service hole cover according to the reference points on the front door panel.
    Text in Illustration 
    *a
    Reference Point

    HINT:
    Securely install the front door service hole cover taking care to prevent wrinkles.



23. INSTALL FRONT DOOR SERVICE HOLE COVER (for 3 Door)
  1. Apply butyl tape to the front door panel.

  1. Pass the front door lock remote control cable, front door inside locking cable and each connector through a new front door service hole cover.



    B284588E01
  1. Install a new front door service hole cover according to the reference points on the front door panel.
    Text in Illustration 
    *a
    Reference Point

    HINT:
    Securely install the front door service hole cover taking care to prevent wrinkles.



24. INSTALL FRONT NO. 1 SPEAKER ASSEMBLY


    E222075E01
  1. Using an air riveter or hand riveter, install the front No. 1 speaker assembly onto the front door panel with 3 new strike rivets.

    HINT:
    Install the new strike rivets in the order shown in the illustration.

    NOTICE:

    1. B130465
      Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

    2. B130466
      Confirm that the rivets are seated properly against the speaker.
    3. Do not tilt the riveter when installing the rivet onto the speaker.
    4. Do not leave any space between the rivet head and speaker.

    5. B130467
      Do not leave any space between the speaker and door. Firmly hold the 2 items together while installing the rivet.

  1. Connect the connector.



25. INSTALL DOOR SIDE AIRBAG SENSOR (for 3 Door)
  1. w/ Curtain Shield Airbag:

    1. Install the door side airbag sensor .



26. INSTALL FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY

HINT:
Use the same procedure as for the LH side .



27. INSTALL FRONT DOOR WINDOW FRAME REAR MOULDING (for 3 Door)

HINT:
Use the same procedure as for the LH side .



28. INSTALL OUTER REAR VIEW MIRROR ASSEMBLY

HINT:
Use the same procedure as for the LH side .



29. INSTALL FRONT DOOR WINDOW FRAME UPPER MOULDING (for Driver Side)

HINT:
Use the same procedure as for the LH side .



30. INSTALL FRONT DOOR WINDOW FRAME FRONT MOULDING

HINT:
Use the same procedure as for the LH side .



31. INSTALL FRONT DOOR GLASS INNER WEATHERSTRIP (for 5 Door)


    B271701
  1. Engage the 7 claws and install the front door glass inner weatherstrip as shown in the illustration.



32. INSTALL FRONT DOOR GLASS INNER WEATHERSTRIP (for 3 Door)


    B284626
  1. Engage the 8 claws and install the front door glass inner weatherstrip as shown in the illustration.



33. INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY


    B271598
  1. Engage the 4 guides and install the front door inside handle.



34. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY (for 5 Door)


    B271597E01
  1. Connect the front door lock remote control cable and the front door inside locking cable to the front door inside handle.
    Text in Illustration 
    *1
    Front Door Lock Remote Control Cable Assembly
    *2
    Front Door Inside Locking Cable Assembly



    B271596
  1. Engage the 7 clips and the front door trim board.



    B271595
  1. Install the 3 screws.



    B275407
  1. Engage the claw and close the cover.



35. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY (for 3 Door)


    B271597E01
  1. Connect the front door lock remote control cable and the front door inside locking cable to the front door inside handle.
    Text in Illustration 
    *1
    Front Door Lock Remote Control Cable Assembly
    *2
    Front Door Inside Locking Cable Assembly



    B284585
  1. Engage the 8 clips and the front door trim board.



    B271595
  1. Install the 3 screws.



    B275407
  1. Engage the claw and close the cover.



36. INSTALL FRONT ARMREST BASE UPPER PANEL (w/ Power Window)
  1. Connect the connector.



    B284582
  1. Engage the 9 claws and 4 guides, and install the front armrest base upper panel.



37. INSTALL FRONT ARMREST BASE UPPER PANEL (w/o Power Window)
  1. Connect the connector.

    HINT:
    If the armrest base upper panel is equipped with door lock switch, connect the connector.



    B284583
  1. Engage the 6 claws and 3 guides, and install the front armrest base upper panel.



38. INSTALL FRONT DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)


    B271669E01
  1. Install the window regulator handle plate.
    Text in Illustration 
    *a
    Inside of Vehicle

  1. Open all the windows.



    B284599E01
  1. Install the front door window regulator handle with clip at the angle shown in the illustration.
    Text in Illustration 
    *a
    Assemble with Glass in Fully Open Position



39. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



40. INSPECT SRS WARNING LIGHT (w/ VSC)
(Click here)


41. INSPECT SRS WARNING LIGHT (w/o VSC)
(Click here)


42. INSPECT POWER WINDOW OPERATION
(Click here)