REAR DOOR > DISASSEMBLY |
| 1. PRECAUTION |
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 3. REMOVE REAR DOOR FRAME GARNISH |
![]() |
Disengage the 2 clips and claw.
Disengage the guide and remove the rear door frame garnish.
| 4. REMOVE REAR DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window) |
![]() |
Insert a clip remover between the plate and front door trim board.
Turn the handle with the clip remover inserted, as shown in the illustration.
Remove the front door window regulator handle and clip.
Remove the window regulator handle plate.
| 5. REMOVE REAR DOOR ARMREST BASE UPPER PANEL (w/ Power Window) |
![]() |
Using a moulding remover, disengage the 9 claws and 3 guides.
Disconnect the connector and remove the rear armrest base upper panel.
| 6. REMOVE REAR DOOR ARMREST BASE UPPER PANEL (w/o Power Window) |
![]() |
Using a moulding remover, disengage the 5 claws and 2 guides and remove the rear armrest base upper panel.
| 7. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY |
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the claw and open the cover.
| *1 | Protective Tape |
![]() |
Remove the 3 screws.
![]() |
Disengage the 7 clips.
![]() |
Disconnect the rear door lock remote control cable assembly and the rear door inside locking cable assembly and remove the rear door trim board.
| *1 | Rear Door Lock Remote Control Cable Assembly |
| *2 | Rear Door Inside Locking Cable Assembly |
| 8. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY |
![]() |
Disengage the 4 guides and remove the rear door inside handle.
| 9. REMOVE REAR DOOR GLASS INNER WEATHERSTRIP |
![]() |
Disengage the 7 claws and remove the rear door glass inner weatherstrip as shown in the illustration.
| 10. REMOVE REAR SPEAKER ASSEMBLY (w/ Rear Speaker) |
![]() |
Disconnect the connector.
![]() |
Drill out the 3 rivet heads using a drill with a bit diameter of less than 4 mm (0.16 in.), and remove the rear speaker assembly from the rear door panel.
Operate the drill around the rivet head circumference and cut out the flange.
After drilling out the flange, continue drilling to push out the shards on the drill.
Using a vacuum cleaner, remove the rivet fragments and shavings from the inside of the door.
| 11. REMOVE REAR DOOR SERVICE HOLE COVER (w/ Rear Speaker) |
![]() |
Remove the rear door service hole cover.
| 12. REMOVE REAR DOOR SERVICE HOLE COVER (w/o Rear Speaker) |
![]() |
| 13. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY |
![]() |
Remove the 3 bolts and nut, and the rear door window division bar.
| 14. REMOVE REAR DOOR GLASS SUB-ASSEMBLY |
![]() |
Slide the lower section of the rear door glass as indicated by the arrow as shown in the illustration.
![]() |
Remove the rear door glass as indicated by the arrows in the order shown in the illustration.
| 15. REMOVE REAR DOOR GLASS CHANNEL SUB-ASSEMBLY |
![]() |
Using a screwdriver with its tip wrapped in protective tape, remove the rear door glass channel.
| *1 | Protective Tape |
| 16. REMOVE REAR DOOR GLASS CHANNEL FILLER |
Remove the rear door glass channel filler.
| 17. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY (w/ Power Window) |
![]() |
Disconnect the connector.
| *1 | Temporary Bolt |
Loosen the temporary bolt.
Remove the 3 bolts.
Remove the temporary bolt and the rear door window regulator.
| 18. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY (w/o Power Window) |
![]() |
Remove the 3 bolts and the rear door window regulator.
| 19. REMOVE REAR DOOR GLASS RUN |
![]() |
Remove the clip.
Disengage the 2 guides and remove the rear door glass run.
| 20. REMOVE REAR DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY |
| 21. REMOVE REAR DOOR LOCK ASSEMBLY (w/ Power Door Lock) |
![]() |
Disconnect the connector.
Using a T30 "TORX" wrench, remove the 3 screws.
![]() |
Slide the rear door lock downward, and remove the rear door lock from the release plate.
| *1 | Release Plate |
![]() | Slide Direction |
![]() |
Remove the door lock wire harness seal from the rear door lock.
| 22. REMOVE REAR DOOR LOCK ASSEMBLY (w/o Power Door Lock) |
![]() |
Using a T30 "TORX" wrench, remove the 3 screws.
![]() |
Slide the rear door lock downward, and remove the rear door lock from the release plate.
| *1 | Release Plate |
![]() | Slide Direction |
![]() |
Remove the door lock wire harness seal from the rear door lock.
| 23. REMOVE REAR DOOR OUTSIDE HANDLE COVER |
![]() |
Using a "TORX" socket wrench T30, loosen the screw.
![]() |
Disengage the 2 claws and remove the rear door outside handle cover.
| 24. REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY |
![]() |
Remove the rear door outside handle in the direction indicated by the arrow as shown in the illustration.
| 25. REMOVE REAR DOOR OUTSIDE HANDLE FRONT PAD |
![]() |
Disengage the 3 claws and remove the rear door outside handle front pad.
| 26. REMOVE REAR DOOR OUTSIDE HANDLE REAR PAD |
![]() |
Disengage the 2 claws and remove the rear door outside handle rear pad.
| 27. REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY |
![]() |
Using a "TORX" socket wrench T30, loosen the screw.
![]() |
Slide the rear door outside handle frame and disengage the grommet and 2 claws of the rear door outside handle frame, and then remove it.
| 28. REMOVE REAR DOOR CHECK ASSEMBLY |
![]() |
Remove the 3 bolts and the rear door check.
| 29. REMOVE REAR DOOR WEATHERSTRIP |
![]() |
Using a clip remover, disengage the 2 clips.
Using a clip remover, disengage the 29 clips and remove the rear door weatherstrip.
| 30. REMOVE NO. 2 BLACK OUT TAPE |