REAR DOOR LOCK > INSTALLATION |
| 1. APPLY BODY GREASE |
| 2. INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY |
Install the rear door inside locking cable to rear door lock.
![]() |
Engage the 4 claws.
| 3. INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY |
Install the rear door lock remote control cable to the rear door lock.
![]() |
Engage the 2 claws.
| 4. INSTALL REAR DOOR LOCK ASSEMBLY (w/ Power Door Lock) |
Install a new door lock wire harness seal to the rear door lock.
Apply MP grease to the sliding parts of the rear door lock.
![]() |
Insert the rear door lock to the release plate.
| *1 | Release Plate |
![]() | Slide Direction |
Using a "TORX" socket wrench T30, install the rear door lock assembly with the 3 screws.
Connect the connector.
| 5. INSTALL REAR DOOR LOCK ASSEMBLY (w/o Power Door Lock) |
Install a new door lock wire harness seal to the rear door lock.
Apply MP grease to the sliding parts of the rear door lock.
![]() |
Insert the rear door lock to the release plate.
| *1 | Release Plate |
![]() | Slide Direction |
Using a "TORX" socket wrench T30, install the rear door lock assembly with the 3 screws.
| 6. INSTALL REAR DOOR GLASS RUN |
![]() |
Engage the 2 guides and install the rear door glass run.
Install the clip.
| 7. INSTALL REAR DOOR GLASS SUB-ASSEMBLY |
![]() |
Insert the rear door glass into the rear door panel along the rear door glass run as indicated by the arrows in the order shown in the illustration.
![]() |
Slide the lower section of the rear door glass as indicated by the arrow as shown in the illustration.
| 8. INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY |
![]() |
Engage the rear door window division bar to the rear door glass run.
Install the rear door window division bar with the 3 bolts and nut.
| 9. INSTALL REAR DOOR SERVICE HOLE COVER (w/ Rear Speaker) |
Apply butyl tape to the rear door panel.
Pass the rear door lock remote control cable, rear door inside locking cable and each connector through a new rear door service hole cover.
![]() |
Install a new rear door service hole cover according to the reference points on the rear door panel.
| *a | Reference Point |
| 10. INSTALL REAR DOOR SERVICE HOLE COVER (w/o Rear Speaker) |
Apply butyl tape to the rear door panel.
Pass the rear door lock remote control cable, rear door inside locking cable and each connector through a new rear door service hole cover.
![]() |
Install a new rear door service hole cover according to the reference points on the rear door panel.
| *a | Reference Point |
| 11. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY |
![]() |
Connect the rear door lock remote control cable and the rear door inside locking cable to the rear door inside handle.
| *1 | Rear Door Lock Remote Control Cable Assembly |
| *2 | Rear Door Inside Locking Cable Assembly |
![]() |
Engage the 7 clips and install the rear door trim board.
![]() |
Install the 3 screws.
![]() |
Engage the claw and close the cover.
| 12. INSTALL REAR DOOR ARMREST BASE UPPER PANEL (w/ Power Window) |
![]() |
Connect the connector.
Engage the 9 claws and 3 guides, and install the rear armrest base upper panel.
| 13. INSTALL REAR DOOR ARMREST BASE UPPER PANEL (w/o Power Window) |
![]() |
Engage the 5 claws and 2 guides, and install the front armrest base upper panel.
| 14. INSTALL REAR DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window) |
![]() |
Install the window regulator handle plate.
| *a | Inside of Vehicle |
Open all the windows.
![]() |
Install the rear door window regulator handle with the clip at the angle shown in the illustration.
| *a | Assemble with Glass in Fully Open Position |
| 15. INSTALL REAR DOOR FRAME GARNISH |
![]() |
Engage the guide.
Engage the 2 clips and claw and install the rear door frame garnish.