COOLING FAN SYSTEM > Cooling Fan Circuit |
| 1.CHECK FAN NO. 1 RELAY (POWER SOURCE) |
![]() |
Remove the FAN No. 1 relay from the engine room R/B.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| FAN No. 1 relay holder 3 - Body ground | Always | 11 to 14 V |
| *1 | Engine Room R/B |
| *2 | FAN No. 1 Relay Holder |
Reinstall the FAN No. 1 relay.
|
| ||||
| OK | |
| 2.CHECK ENGINE ROOM R/B |
![]() |
Remove the FAN No. 1 relay and FAN No. 2 relay from the engine room R/B.
Turn the Ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| FAN No. 1 relay holder 1 - Body ground | Ignition switch ON | 11 to 14 V |
| FAN No. 2 relay holder 2 - Body ground | Ignition switch ON | 11 to 14 V |
| *1 | Engine Room R/B |
| *2 | FAN No. 1 Relay Holder |
| *3 | FAN No. 2 Relay Holder |
Reinstall the FAN No. 1 relay and FAN No. 2 relay.
|
| ||||
| OK | |
| 3.INSPECT FAN NO. 1 RELAY |
Inspect the FAN No. 1 relay (Click here).
|
| ||||
| OK | |
| 4.INSPECT FAN NO. 2 RELAY |
Inspect the FAN No. 2 relay (Click here).
|
| ||||
| OK | |
| 5.INSPECT COOLING FAN RESISTOR |
Inspect the cooling fan resistor (Click here).
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (FAN NO. 2 RELAY - BODY GROUND) |
Remove the FAN No. 2 relay from the engine room R/B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| FAN No. 2 relay holder 5 - Body ground | Always | Below 1 Ω |
Reinstall the FAN No. 2 relay.
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (COOLING FAN RESISTOR - BODY GROUND) |
Disconnect the cooling fan resistor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A22-1 (-) - Body ground | Always | Below 1 Ω |
Connect the cooling fan resistor connector.
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR (FAN NO. 2 RELAY - COOLING FAN RESISTOR) |
Disconnect the cooling fan resistor connector.
Remove the FAN No. 2 relay from the engine room R/B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| FAN No. 2 relay holder 4 - A22-2 (+) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| A22-2 (+) or FAN No. 2 relay holder 4 - Body ground | Always | 10 kΩ or higher |
Reinstall the FAN No. 2 relay.
Reconnect the cooling fan resistor connector.
|
| ||||
| OK | |
| 9.CHECK COOLING FAN MOTOR |
Inspect the cooling fan motor (Click here).
|
| ||||
| OK | |
| 10.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - FAN NO. 1 RELAY) |
Disconnect the cooling fan motor connector.
Remove the FAN No. 1 relay from the engine room R/B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A21-2 - FAN No. 1 relay holder 5 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| A21-2 or FAN No. 1 relay holder 5 - Body ground | Always | 10 kΩ or higher |
Reinstall the FAN No. 1 relay.
Reconnect the cooling fan motor connector.
|
| ||||
| OK | |
| 11.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - FAN NO. 2 RELAY) |
Disconnect the cooling fan motor connector.
Remove the FAN No. 2 relay from the engine room R/B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A21-1 - FAN No. 2 relay holder 3 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| A21-1 or FAN No. 2 relay holder 3 - Body ground | Always | 10 kΩ or higher |
Reinstall the FAN No. 2 relay.
Reconnect the cooling fan motor connector.
|
| ||||
| OK | |
| 12.CHECK HARNESS AND CONNECTOR (ENGINE ROOM R/B - ECM) |
Remove the FAN No. 1 relay and FAN No. 2 relay from the engine room R/B.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A74-41 (FANH) - FAN No. 2 relay holder 1 | Always | Below 1 Ω |
| A74-49 (FANL) - FAN No. 1 relay holder 2 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| A74-41 (FANH) or FAN No. 2 relay holder 1 - Body ground | Always | 10 kΩ or higher |
| A74-49 (FANL) or FAN No. 1 relay holder 2 - Body ground | Always | 10 kΩ or higher |
Reconnect the ECM connector.
Reinstall the FAN No. 1 relay and FAN No. 2 relay.
|
| ||||
| OK | ||
| ||