Home › Drivetrain ยท DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY

FRONT DRIVE SHAFT ASSEMBLY > REASSEMBLY

for Preparation Click here



1. INSTALL FRONT DRIVE SHAFT DUST COVER


    C235587E01
  1. Using SST and a press, install a new dust cover into the inboard joint until it is flush with the end.
    Text in Illustration 
    *1
    Press

    SST
    09527-10011  

    NOTICE:
    1. Install the dust cover in the correct orientation.
    2. Do not deform the dust cover.

    HINT:
    Use the same procedure for the RH side as for the LH side.



2. INSTALL FRONT DRIVE SHAFT HOLE SNAP RING LH
  1. Install a new snap ring.



3. INSTALL FRONT DRIVE SHAFT HOLE SNAP RING RH

HINT:
Use the same procedure for the RH side as for the LH side.



4. INSTALL FRONT AXLE OUTBOARD JOINT BOOT


    C177228E02
  1. Wrap the spline of the outboard joint shaft with protective tape.
    Text in Illustration 
    *1
    Protective Tape

  1. Install new parts onto the outboard joint shaft in the following order.
    Installation Order 
    Order
    Part Name
    1.
    Front No. 2 axle outboard joint boot clamp
    2.
    Front axle outboard joint boot
    3.
    Front axle outboard joint boot clamp

  1. Pack the joint portion of the outboard joint shaft and the outboard joint boot with grease.

    Standard Quantity:
    Engine Type
    Quantity
    1NZ-FE
    116 to 126 g (4.1 to 4.4 oz.)
    2NZ-FE
    90 to 100 g (3.2 to 3.5 oz.)

  1. Install the outboard joint boot onto the outboard joint shaft groove.

    NOTICE:
    Keep the groove free of grease.

    HINT:
    Use the same procedure for the RH side as for the LH side.



5. INSTALL FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP

CAUTION:
Wear protective gloves to avoid injuries to your hands.



    C107943
  1. Install a new boot clamp onto the outboard joint boot and provisionally fold back the lever.

    NOTICE:
    1. Set the lever into the guide groove correctly and install the clamp as far into the inner side of the vehicle as possible.
    2. Check the band and the lever for any deformation before folding back the lever.



    C112269E20
  1. Lean your weight on your hand and roll the outboard joint forward while pressing the outboard joint against the work plane. Roll the outboard joint and fold the lever until a click sound can be heard.
    Text in Illustration 
    *a
    Weight
    *b
    Contact

    NOTICE:
    1. Do not damage the deflector.
    2. Make sure that the outboard joint is in direct contact with the work plane.



    C205460
  1. Using a plastic hammer, tap the buckle to fix it while adjusting the clearance between the lever and the groove to make the clearances between the buckle edge and the lever end even.

    NOTICE:
    Do not damage the outboard joint boot.

    HINT:
    Use the same procedure for the RH side as for the LH side.



6. INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP

CAUTION:
Wear protective gloves to avoid injuries to your hands.



    C107948
  1. Install a new boot clamp onto the outboard joint boot and provisionally fold back the lever.

    NOTICE:
    1. Set the lever into the guide groove correctly.
    2. Check the band and the lever for any deformation before folding back the lever.



    C158356E11
  1. Using water pump pliers, pinch the boot clamp to provisionally fix it.
    Text in Illustration 
    *a
    Place the tip near the center of the lever.



    C112272
  1. Using a plastic hammer, tap the buckle to fix it while adjusting the clearance between the lever and the groove to make the clearances between the buckle edge and the lever end even.

    NOTICE:
    Do not damage the outboard joint boot.

    HINT:
    Use the same procedure for the RH side as for the LH side.



7. INSTALL FRONT DRIVE SHAFT DAMPER RH


    C189618E03
  1. Install the drive shaft damper onto dimension (A) shown in the illustration.

    Dimension (A):
    Engine Type
    Dimension
    1NZ-FE
    425.6 to 429.6 mm
    (16.76 to 16.91 in.)
    2NZ-FE
    416.0 to 420.0 mm
    (16.38 to 16.54 in.)

    NOTICE:
    Install the damper in the correct orientation.



8. INSTALL FRONT DRIVE SHAFT DAMPER CLAMP RH


C196491E05
  1. One touch type:

    1. Install a new damper clamp onto the front drive shaft damper and fix the damper clamp with a screwdriver.

  1. Claw engagement type:

    1. Using needle-nose pliers, install a new damper clamp as shown in the illustration.
      Text in Illustration 
      *a
      One Touch Type
      *b
      Claw Engagement Type



9. INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY
  1. Install a new parts onto the outboard joint shaft in the following order.
    Installation Order 
    Order
    Part Name
    1.
    Front axle inboard joint boot clamp
    2.
    Front axle inboard joint boot
    3.
    Front No. 2 axle inboard joint boot clamp

  1. Fix the outboard joint shaft in a vise between aluminum plates.

    NOTICE:
    Do not overtighten the vise.

  1. Remove the protective tape.



    F047445E07
  1. Align the matchmarks and install the tripod joint onto the outboard joint shaft.
    Text in Illustration 
    *a
    Matchmark

    NOTICE:
    Face the serrated side of the tripod joint outward and install it onto the outboard joint end.

  1. Using a brass bar and hammer, install the tripod joint.

    NOTICE:
    1. Do not hit the rollers.
    2. Keep the tripod joint free of foreign matter.



    C160822
  1. Using a snap ring expander, install a new snap ring.

  1. Pack the inboard joint with grease.

    Standard Quantity:
    Engine Type
    Quantity
    1NZ-FE
    125 to 135 g (4.4 to 4.8 oz.)
    2NZ-FE
    112 to 122 g (4.0 to 4.3 oz.)



    C160821E11
  1. Align the matchmarks and install the inboard joint onto the outboard joint shaft.
    Text in Illustration 
    *a
    Matchmark

    HINT:
    Use the same procedure for the RH side as for the LH side.



10. INSTALL FRONT AXLE INBOARD JOINT BOOT
  1. Install the inboard joint boot into the grooves of the inboard joint and outboard joint shaft.

    NOTICE:
    Keep the grooves free of grease.

    HINT:
    Use the same procedure for the RH side as for the LH side.



11. INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP

CAUTION:
Wear protective gloves to avoid injuries to your hands.



  1. One touch type:



      C107948
    1. Install a new boot clamp onto the inboard joint boot and provisionally fold back the lever.

      NOTICE:
      1. Set the lever into the guide groove correctly.
      2. Check the band and the lever for any deformation before folding back the lever.



    2. C158356E12
    3. Using water pump pliers, pinch the boot clamp to provisionally fix it.
      Text in Illustration 
      *a
      Place the tip near the center of the lever.



    4. C112272
    5. Using a plastic hammer, tap the buckle to fix it while adjusting the clearance between the lever and the groove to make the clearances between the buckle edge and the lever end even.

      NOTICE:
      Do not damage the inboard joint boot.



  1. Claw engagement type:



      C157519
    1. Using needle-nose pliers, install a new clamp as shown in the illustration.

      NOTICE:
      1. Do not damage the boot.
      2. Do not deform the claw of the hook.

      HINT:
      Use the same procedure for the RH side as for the LH side.



12. INSTALL FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP
  1. Install a new boot clamp onto the inboard joint boot.



    C205466E01
  1. Adjust dimension (A) until the drive shaft is within the specified length.

    Dimension (A):
    Engine Type
    LH
    RH
    1NZ-FE
    584.3 mm (23.00 in.)
    826.3 mm (32.53 in.)
    2NZ-FE
    589.3 mm (23.20 in.)
    829.3 mm (32.65 in.)



  1. One touch type:



      C235649
    1. Install a new boot clamp onto the inboard joint boot and provisionally fold back the lever.

      CAUTION:
      Wear protective gloves to avoid injuries to your hands.

      NOTICE:
      1. Set the lever into the guide groove correctly.
      2. Check the band and the lever for any deformation before folding back the lever.



    2. C235640E01
    3. Lean your weight on your hand and roll the outboard joint forward while pressing the outboard joint against the work plane. Roll the outboard joint and fold the lever until a click sound can be heard.
      Text in Illustration 
      *a
      Weight
      *b
      Contact

      NOTICE:
      1. Do not damage the deflector.
      2. Make sure that the inboard joint is in direct contact with the work plane.



    4. C204043
    5. Using a plastic hammer, tap the buckle to fix it while adjusting the clearance between the lever and the groove to make the clearances between the buckle edge and the lever end even.

      NOTICE:
      Do not damage the boot.



  1. Claw engagement type:



      C157518
    1. Using needle-nose pliers, engage the 2 claws and install the boot clamp as shown in the illustration.

      NOTICE:
      1. Do not damage the boot.
      2. Do not deform the claw of the hook.

      HINT:
      Use the same procedure for the RH side as for the LH side.



13. INSPECT FRONT DRIVE SHAFT ASSEMBLY


    C205473
  1. Check for noticeable looseness when turning the joint up and down, left and right, and in the thrust direction.

  1. Check for cracks, damage and grease leakage on the boot joint.

    HINT:
    Keep the drive shaft level while moving it.



    C205466E01
  1. Check dimension (A).

    Dimension (A):
    Engine Type
    LH
    RH
    1NZ-FE
    584.3 mm (23.00 in.)
    826.3 mm (32.53 in.)
    2NZ-FE
    589.3 mm (23.20 in.)
    829.3 mm (32.65 in.)