Home › Vehicle Exterior › WINDOW / GLASS › WINDOW DEFOGGER SYSTEM

WINDOW DEFOGGER SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (for Automatic Air Conditioning System)

E233186E01

  1. Disconnect the F42 air conditioning amplifier assembly connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F42-1 (IG+) - F42-14 (GND)
    V - W-B
    Ignition power supply
    Ignition switch ON
    11 to 14 V
    Ignition switch off
    Below 1 V
    F42-14 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    F42-21 (B) - F42-14 (GND)
    BE - W-B
    Battery power supply
    Always
    11 to 14 V

    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the air conditioning amplifier assembly connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F42-37 (LIN1) - F42-14 (GND)
    LG - W-B
    LIN communication signal
    Ignition switch ON
    Pulse generation
    F42-38 (RDFG) - F42-14 (GND)
    B - W-B
    DEF relay
    Ignition switch ON, rear window defogger switch OFF
    11 to 14 V
    Ignition switch ON, rear window defogger switch ON
    Below 1 V

    1. If the result is not as specified, the air conditioning amplifier assembly may have a malfunction.


CHECK AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System)

E233187E01

  1. Disconnect the F40 air conditioning control assembly connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F40-5 (IG+) - F40-8 (GND)
    V - BR
    Ignition power supply
    Ignition switch ON
    11 to 14 V
    Ignition switch off
    Below 1 V
    F40-8 (GND) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω

    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the air conditioning control assembly connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F40-3 (LIN1) - F40-8 (GND)
    LG - BR
    LIN communication signal
    Ignition switch ON
    Pulse generation

    1. If the result is not as specified, the air conditioning control assembly may have a malfunction.


CHECK NO. 3 HEATER CONTROL SUB-ASSEMBLY (for Manual Air Conditioning System)

B291805E01

  1. Disconnect the F37 No. 3 heater control sub-assembly connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F37-1 (E) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    F37-3 (IG+) - F37-1 (E)
    V - BR
    Ignition power supply
    Ignition switch ON
    11 to 14 V
    Ignition switch off
    Below 1 V

    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the No. 3 heater control sub-assembly connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F37-2 (RDEF) - F37-1 (E)
    B - BR
    Rear window defogger signal
    Ignition switch ON, rear window defogger switch OFF
    11 to 14 V
    Ignition switch ON, rear window defogger switch ON
    Below 1 V

    1. If the result is not as specified, the No. 3 heater control sub-assembly may have a malfunction.