Home › Engine / Hybrid System ยท 2NZ-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P0606    ECM / PCM Processor

for Preparation Click here


DESCRIPTION

The ECM continuously monitors its main and sub CPUs. This self-check ensures that the ECM is functioning properly. If outputs from the CPUs are different and deviate from the standard, the ECM will illuminate the MIL and store a DTC immediately.

DTC No.
DTC Detection Condition
Trouble Area
P0606
Either condition is met (1 trip detection logic):
  1. There is an ECM main CPU error.
  2. There is an ECM sub CPU error.
ECM

MONITOR STRATEGY


Required Sensors/Components
ECM
Frequency of Operation
Continuous

CONFIRMATION DRIVING PATTERN

NOTICE:
After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).

  1. Connect the intelligent tester to the DLC3.
  2. Turn the ignition switch to ON and turn the tester on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the tester off.
  5. Turn the ignition switch off.
  6. Disconnect the tester.
  7. Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.
  8. Connect the cable to the negative (-) battery terminal.
  9. Connect the tester to the DLC3.
  10. Turn the ignition switch to ON and turn the tester on.
  11. Wait 10 seconds or more.
  12. Enter the following menus: Powertrain / Engine and ECT / DTC.
  13. Read pending DTCs.

    HINT:
    1. If a DTC is output, the system is malfunctioning.
    2. If a DTC is not output, perform the following procedure.

  14. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  15. Input the DTC: P0606.
  16. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and the DTC judgment result again.


INSPECTION PROCEDURE

NOTICE:
After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK FOR DTC (DTC P0606)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Clear DTCs (Click here).

  1. Turn the tester off.

  1. Turn the ignition switch off.

  1. Disconnect the tester.

  1. Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.

  1. Connect the cable to the negative (-) battery terminal.

  1. Connect the tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Wait 10 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    OK:
    P0606 is not output.



NG
REPLACE ECM (Click here)
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)