Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE FLUID

BRAKE FLUID > REPLACEMENT

for Preparation Click here


NOTICE:
Immediately wash off any brake fluid that comes into contact with any painted surfaces.

HINT:
If any work is done on the brake system or if air in the brake lines is suspected, bleed the air from the system.



1. REMOVE CENTER COWL TOP VENTILATOR LOUVER (for LHD)


C241431
  1. Disengage the 2 clips and slide the hood to cowl top seal as shown in the illustration.



    C241408
  1. Disengage the 2 claws and separate the washer hose joint.

    NOTICE:
    To prevent washer fluid from contaminating the brake master cylinder reservoir, do not separate the washer hose.

  1. Disengage the 2 claws and 6 guides remove the cowl top ventilator louver center.



2. REMOVE CENTER COWL TOP VENTILATOR LOUVER (for RHD)


C235582
  1. Disengage the clip and slide the hood to cowl top seal as shown in the illustration.



    C234714
  1. Disengage the 2 claws and separate the washer hose joint.

    NOTICE:
    To prevent washer fluid from contaminating the brake master cylinder reservoir, do not separate the washer hose.

  1. Disengage the 2 claws and 4 guides and remove the center cowl top ventilator louver.



3. FILL RESERVOIR WITH BRAKE FLUID


    C241430E01
  1. Fill the reservoir with brake fluid.
    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *a
    MAX Line
    *b
    MIN Line

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3

    NOTICE:
    Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brakes.



4. REPLACE BRAKE FLUID


    C182332
  1. Connect a vinyl tube to the bleeder plug.

  1. Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed (Step C).

  1. At the point where the fluid stops coming out, tighten the bleeder plug, and then release the brake pedal (Step D).

  1. Repeat Steps C and D until the new brake fluid is comes out.

  1. Tighten the bleeder plug.

    Torque:
    Front Brake:
    8.3 N*m{ 85 kgf*cm , 73 in.*lbf }
    Rear Brake:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

  1. Repeat the above procedure to bleed the air out of the brake line for each wheel.



5. INSPECT FOR BRAKE FLUID LEAK


6. INSPECT FLUID LEVEL


    C241430E01
  1. Check the fluid level.
    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *a
    MAX Line
    *b
    MIN Line
    If brake fluid level is lower than the MIN line, check for leaks and inspect the disc brake pads. If necessary, refill the reservoir with brake fluid to the MAX line after repair or replacement.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT 3



7. INSTALL CENTER COWL TOP VENTILATOR LOUVER (for LHD)


C241408
  1. Engage the 2 claws and 6 guides and install the cowl top ventilator louver center.

  1. Engage the 2 claws and install the washer hose joint.



    C241854
  1. Engage the 2 clips and slide the hood to cowl top seal as shown in the illustration.



8. INSTALL CENTER COWL TOP VENTILATOR LOUVER (for RHD)


C234714
  1. Engage the 2 claws and 4 guides and install the center cowl top ventilator louver.

  1. Engage the 2 claws and install the washer hose joint.



    C235583
  1. Engage the clip and slide the hood to cowl top seal as shown in the illustration.