BRAKE FLUID > BLEEDING |
| 1. REMOVE CENTER COWL TOP VENTILATOR LOUVER (for LHD) |
![]() |
Disengage the 2 clips and slide the hood to cowl top seal as shown in the illustration.
![]() |
Disengage the 2 claws and separate the washer hose joint.
Disengage the 2 claws and 6 guides remove the cowl top ventilator louver center.
| 2. REMOVE CENTER COWL TOP VENTILATOR LOUVER (for RHD) |
![]() |
Disengage the clip and slide the hood to cowl top seal as shown in the illustration.
![]() |
Disengage the 2 claws and separate the washer hose joint.
Disengage the 2 claws and 4 guides and remove the center cowl top ventilator louver.
| 3. FILL RESERVOIR WITH BRAKE FLUID |
![]() |
Fill the reservoir with brake fluid.
| *A | for LHD |
| *B | for RHD |
| *a | MAX Line |
| *b | MIN Line |
| 4. BLEED BRAKE MASTER CYLINDER SUB-ASSEMBLY (w/o VSC) |
![]() |
Using a union nut wrench 10 mm, separate the 2 brake tubes from the master cylinder.
| *A | for LHD |
| *B | for RHD |
![]() |
Slowly depress the brake pedal and hold it there (Step A).
| *A | for LHD |
| *B | for RHD |
![]() |
Block the outer holes with your fingers, and release the brake pedal (Step B).
| *A | for LHD |
| *B | for RHD |
Repeat Steps A and B 3 or 4 times.
![]() |
Using a union nut wrench 10 mm, install the 2 brake tubes into the master cylinder.
| *A | for LHD |
| *B | for RHD |
| 5. BLEED BRAKE MASTER CYLINDER SUB-ASSEMBLY (w/ VSC) |
![]() |
Using a union nut wrench 12 mm, separate the 2 brake tubes from the master cylinder.
| *A | for LHD |
| *B | for RHD |
![]() |
Slowly depress the brake pedal and hold it there (Step A).
| *A | for LHD |
| *B | for RHD |
![]() |
Block the outer holes with your fingers, and release the brake pedal (Step B).
| *A | for LHD |
| *B | for RHD |
Repeat Steps A and B 3 or 4 times.
![]() |
Using a union nut wrench 12 mm, install the 2 brake tubes into the master cylinder.
| *A | for LHD |
| *B | for RHD |
| 6. BLEED BRAKE LINE |
![]() |
Connect a vinyl tube to the bleeder plug.
Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed (Step C).
At the point where the fluid stops coming out, tighten the bleeder plug, and then release the brake pedal (Step D).
Repeat Steps C and D until all the air in the fluid is completely bled out.
Tighten the bleeder plug.
Repeat the above procedure to bleed the air out of the brake line for each wheel.
| 7. BLEED BRAKE ACTUATOR ASSEMBLY |
Depress the brake pedal more than 20 times with the engine off.
Connect the intelligent tester to the DLC3, and turn the ignition switch to ON.
Select "Air Bleeding" on the intelligent tester.
Bleed the air out of the brake line when Step 1: Increase appears on the intelligent tester display.
![]() |
Connect the vinyl tube to either one of the bleeder plugs.
Depress the brake pedal several times, and then loosen the bleeder plug connected to the vinyl tube with the pedal depressed (Step E).
When fluid stops coming out, tighten the bleeder plug and release the brake pedal (Step F).
Repeat Steps E and F until all the air in the fluid is completely bled out.
Tighten the bleeder plug completely.
Repeat the above procedure for each wheel to bleed the air out of the brake line.
Bleed the air out of the suction line when Step 2: Inhalation appears on the intelligent tester display.
Connect the vinyl tube to the bleeder plug at the right front wheel or the right rear wheel and loosen the bleeder plug.
Operate the brake actuator to bleed the air using the intelligent tester (Step G).
Check if the operation has stopped by referring to the intelligent tester display and tighten the bleeder plug (Step H).
Repeat Steps G and H until all the air in the fluid is completely bled out.
Tighten the bleeder plug.
Repeat the above procedure for the other wheels to bleed the air out of the brake line.
Bleed the air out of the pressure reduction line when Step 3: Decrease appears on the intelligent tester display.
Connect a vinyl tube to either one of the bleeder plugs.
Loosen the bleeder plug (Step I).
Using the intelligent tester, operate the brake actuator assembly, completely depress the brake pedal and hold it there (Step J).
Tighten the bleeder plug, and then release the brake pedal (Step K).
Repeat Steps I to K until all the air in the fluid is completely bled out.
Tighten the bleeder plug.
Repeat the above procedure for the other wheels to bleed the air out of the brake line.
Bleed the air out of the brake line again when Step 4: Increase appears on the intelligent tester display.
![]() |
Connect the vinyl tube to either one of the bleeder plugs.
Depress the brake pedal several times, and then loosen the bleeder plug connected to the vinyl tube with the pedal depressed (Step L).
When fluid stops coming out, tighten the bleeder plug, then release the brake pedal (Step M).
Repeat Steps L and M until all the air in the fluid is completely bled out.
Tighten the bleeder plug.
Repeat the above procedure for the other wheels to bleed the air out of the brake line.
Make sure that the air bleeding is complete by referring to the intelligent tester display and turn off the intelligent tester.
Disconnect the intelligent tester from the DLC3.
Turn the ignition switch off.
| 8. INSPECT FOR BRAKE FLUID LEAK |
| 9. INSPECT FLUID LEVEL |
![]() |
Check the fluid level.
| *A | for LHD |
| *B | for RHD |
| *a | MAX Line |
| *b | MIN Line |
| 10. INSTALL CENTER COWL TOP VENTILATOR LOUVER (for LHD) |
![]() |
Engage the 2 claws and 6 guides and install the cowl top ventilator louver center.
Engage the 2 claws and install the washer hose joint.
![]() |
Engage the 2 clips and slide the hood to cowl top seal as shown in the illustration.
| 11. INSTALL CENTER COWL TOP VENTILATOR LOUVER (for RHD) |
![]() |
Engage the 2 claws and 4 guides and install the center cowl top ventilator louver.
Engage the 2 claws and install the washer hose joint.
![]() |
Engage the clip and slide the hood to cowl top seal as shown in the illustration.