Home › Vehicle Exterior › WIPER / WASHER › WIPER SWITCH

WIPER SWITCH > INSPECTION

for Preparation Click here



1. INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY (for LHD)


    E171721E37
  1. Check the front wiper switch.
    Text in Illustration 
    *a
    Component without harness connected
    (Windshield Wiper Switch Assembly)

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Front Wiper Switch 
      Tester Connection
      Switch Condition
      Specified Condition
      F12-1 (+S) - F12-3 (+1)
      OFF
      Below 1 Ω
      INT
      F12-2 (+B) - F12-3 (+1)
      MIST
      LO
      F12-2 (+B) - F12-4 (+2)
      HI

      If the result is not as specified, replace the wiper switch.



    E171721E38
  1. Check the front washer switch.
    Text in Illustration 
    *a
    Component without harness connected
    (Windshield Wiper Switch Assembly)

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Front Washer Switch 
      Tester Connection
      Switch Condition
      Specified Condition
      F11-2 (EW) - F11-3 (WF)
      ON
      Below 1 Ω
      OFF
      10 kΩ or higher

      If the result is not as specified, replace the wiper switch.



  1. Check the intermittent operation.


    E232203E01


    Text in Illustration 
    *A
    FAST: Connect battery negative lead to terminal F12-1 (+S)
    *B
    SLOW: Connect battery negative lead to terminal F12-1 (+S)
    *a
    Component without harness connected
    (Windshield Wiper Switch Assembly)
    *b
    Voltage between terminals F12-4 (+2) and F11-2 (EW)
    *c
    Wiper Switch
    *d
    Stop
    *e
    Start
    *f
    1.6 +/- 1 seconds
    *g
    10.7 +/- 5 seconds
    -
    -
    1. Connect the positive (+) lead to terminal F12-3 (+1) and the negative (-) lead to terminal F11-2 (EW).
    2. Connect the positive (+) lead to terminal F12-2 (+B) and the negative (-) lead to terminal F11-2 (EW) and F12-1 (+S).
    3. Turn the wiper switch to the INT position.
    4. Connect the positive (+) lead to terminal F12-1 (+S) for 5 seconds.
    5. Connect the negative (-) lead to terminal F12-1 (+S).
    6. Operate the intermittent wiper relay and check the voltage between terminals F12-3 (+1) and F11-2 (EW).

      OK:
      Voltage changes as shown in the illustration.

      If the result is not as specified, replace the wiper switch.



  1. Check the front washer operation.


    E232204E01


    Text in Illustration 
    *1
    Washer Switch
    -
    -
    *a
    Component without harness connected
    (Windshield Wiper Switch Assembly)
    *b
    Voltage between terminals F12-3 (+1) and F11-2 (EW)
    *c
    Approximately 0.5 seconds
    *d
    Approximately 2.2 seconds
    1. Connect the positive (+) lead to terminal F12-2 (+B) and the negative (-) lead to terminal F12-1 (+S) and F11-2 (EW).
    2. Connect the positive (+) lead to terminal F12-3 (+1) and the negative (-) lead to terminal F11-2 (EW).
    3. Turn the washer switch on and off, and check the voltage between terminals F12-3 (+1) and F11-2 (EW).

      OK:
      Voltage changes as shown in the illustration.

      If the result is not as specified, replace the wiper switch.



  1. Check the rear wiper switch (w/ Rear Wiper).



      E171721E39
    1. Measure the resistance according to the value(s) in the table below.
      Text in Illustration 
      *a
      Component without harness connected
      (Windshield Wiper Switch Assembly)

      Standard Resistance:
      Rear Wiper Switch 
      Tester Connection
      Switch Condition
      Specified Condition
      F11-7 (+1R) - F11-2 (EW)
      OFF
      10 kΩ or higher
      F11-7 (+1R) - F11-2 (EW)
      ON
      Below 1 Ω

      If the result is not as specified, replace the wiper switch.



    E171721E40
  1. Check the rear washer switch (w/ Rear Wiper).
    Text in Illustration 
    *a
    Component without harness connected
    (Windshield Wiper Switch Assembly)

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Rear Washer Switch 
      Tester Connection
      Switch Condition
      Specified Condition
      F12-5 (WR) - F11-2 (EW)
      OFF
      10 kΩ or higher
      F11-7 (+1R) - F11-2 (EW)
      F12-5 (WR) - F11-2 (EW)
      WASH
      Below 1 Ω
      F12-5 (WR) - F11-2 (EW)
      ON + WASH
      Below 1 Ω
      F11-7 (+1R) - F11-2 (EW)

      If the result is not as specified, replace the wiper switch.



2. INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY (for RHD)


    E136492E06
  1. Check the front wiper switch.
    Text in Illustration 
    *a
    Component without harness connected
    (Windshield Wiper Switch Assembly)

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Front Wiper Switch 
      Tester Connection
      Switch Condition
      Specified Condition
      F12-4 (+S) - F12-2 (+1)
      OFF
      Below 1 Ω
      INT
      F12-3 (+B) - F12-2 (+1)
      MIST
      LO
      F12-3 (+B) - F12-1 (+2)
      HI

      If the result is not as specified, replace the wiper switch.



    E136492E07
  1. Check the front washer switch.
    Text in Illustration 
    *a
    Component without harness connected
    (Windshield Wiper Switch Assembly)

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Front Washer Switch 
      Tester Connection
      Switch Condition
      Specified Condition
      F11-2 (EW) - F11-1 (WF)
      ON
      Below 1 Ω
      OFF
      10 kΩ or higher

      If the result is not as specified, replace the wiper switch.



  1. Check the intermittent operation.


    E232205E01


    Text in Illustration 
    *A
    FAST: Connect battery negative lead to terminal F12-4 (+S)
    *B
    SLOW: Connect battery negative lead to terminal F12-4 (+S)
    *a
    Component without harness connected
    (Windshield Wiper Switch Assembly)
    *b
    Voltage between terminals F12-1 (+2) and F11-2 (EW)
    *c
    Wiper Switch
    *d
    Stop
    *e
    Start
    *f
    1.6 +/- 1 seconds
    *g
    10.7 +/- 5 seconds
    -
    -
    1. Connect the positive (+) lead to terminal F12-2 (+1) and the negative (-) lead to terminal F11-2 (EW).
    2. Connect the positive (+) lead to terminal F12-3 (+B) and the negative (-) lead to terminal F11-2 (EW) and F12-4 (+S).
    3. Turn the wiper switch to the INT position.
    4. Connect the positive (+) lead to terminal F12-4 (+S) for 5 seconds.
    5. Connect the negative (-) lead to terminal F12-4 (+S).
    6. Operate the intermittent wiper relay and check the voltage between terminals F12-2 (+1) and F11-2 (EW).

      OK:
      Voltage changes as shown in the illustration.

      If the result is not as specified, replace the wiper switch.



  1. Check the front washer operation.


    E232206E01


    Text in Illustration 
    *1
    Washer Switch
    -
    -
    *a
    Component without harness connected
    (Windshield Wiper Switch Assembly)
    *b
    Voltage between terminals F12-2 (+1) and F11-2 (EW)
    *c
    Approximately 0.5 seconds
    *d
    Approximately 2.2 seconds
    1. Connect the positive (+) lead to terminal F12-3 (+B) and the negative (-) lead to terminal F12-1 (+S) and F11-2 (EW).
    2. Connect the positive (+) lead to terminal F12-2 (+1) and the negative (-) lead to terminal F11-2 (EW).
    3. Turn the washer switch on and off, and check the voltage between terminals F12-2 (+1) and F11-2 (EW).

      OK:
      Voltage changes as shown in the illustration.

      If the result is not as specified, replace the wiper switch.



    E136492E08
  1. Check the rear wiper switch (w/ Rear Wiper).
    Text in Illustration 
    *a
    Component without harness connected
    (Windshield Wiper Switch Assembly)

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Rear Wiper Switch 
      Tester Connection
      Switch Condition
      Specified Condition
      F11-4 (+1R) - F11-2 (EW)
      OFF
      10 kΩ or higher
      F11-4 (+1R) - F11-2 (EW)
      ON
      Below 1 Ω

      If the result is not as specified, replace the wiper switch.



    E136492E10
  1. Check the rear washer switch (w/ Rear Wiper).
    Text in Illustration 
    *a
    Component without harness connected
    (Windshield Wiper Switch Assembly)

    Standard Resistance:
    Rear Washer Switch 
    Tester Connection
    Switch Condition
    Specified Condition
    F12-10 (WR) - F11-2 (EW)
    OFF
    10 kΩ or higher
    F11-4 (+1R) - F11-2 (EW)
    F12-10 (WR) - F11-2 (EW)
    WASH
    Below 1 Ω
    F12-10 (WR) - F11-2 (EW)
    ON + WASH
    Below 1 Ω
    F11-4 (+1R) - F11-2 (EW)

    If the result is not as specified, replace the wiper switch.