Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING PANEL (for Manual Air Conditioning System)

AIR CONDITIONING PANEL (for Manual Air Conditioning System) > INSPECTION

for Preparation Click here



1. INSPECT NO. 1 HEATER CONTROL SUB-ASSEMBLY (w/ Heater)


  1. Check the No. 1 heater control sub-assembly resistance.



      E218261E01
    1. Measure the resistance according to the value(s) in the table below.
      Text in Illustration 
      *1
      A/C Switch
      *a
      Component without harness connected
      (No. 1 Heater Control Sub-assembly)

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      2 (L) - 3 (E)
      Always
      10 kΩ or higher
      2 (L) - 4 (B)
      A/C switch ON
      Below 1 Ω
      2 (L) - 4 (B)
      A/C switch OFF
      10 kΩ or higher
      3 (E) - 4 (B)
      Always
      10 kΩ or higher
      5 (ILL+) - 6 (ILL-)
      Always
      Below 1 Ω

      If the result is not as specified, replace the No. 1 heater control sub-assembly.

  1. Check that the A/C switch indicator.

    1. Connect the positive (+) lead from the battery to terminal 2 (L) and the negative (-) lead to terminal 3 (E).

    2. Push the A/C switch in and check that the indicator lights up.

      OK:
      Indicator lights up

      If the result is not as specified, replace the heater control sub-assembly.

  1. Check that the heater control illuminates.

    1. Apply battery voltage to the heater control sub-assembly and check that the heater control sub-assembly illuminates.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → 5(ILL+)
      Battery negative (-) → 6(ILL-)
      illuminates

      If the result is not as specified, replace the bulb.



2. INSPECT NO. 1 HEATER CONTROL SUB-ASSEMBLY (w/o Heater)


  1. Check the No. 1 heater control sub-assembly resistance.



      I107003E01
    1. Measure the resistance according to the value(s) in the table below.
      Text in Illustration 
      *a
      Component without harness connected
      (No. 1 Heater Control Sub-assembly)

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      2 (L) - 4 (B)
      Always
      Below 1 Ω

      If the result is not as specified, replace the No. 1 heater control sub-assembly.

  1. Check that the heater control illuminates.

    1. Apply battery voltage to the heater control sub-assembly and check that the heater control sub-assembly illuminates.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → 5(ILL+)
      Battery negative (-) → 6(ILL-)
      illuminates

      If the result is not as specified, replace the bulb.



3. INSPECT NO. 2 HEATER CONTROL SUB-ASSEMBLY


  1. Check the No. 2 heater control sub-assembly resistance.



      I106080E01
    1. Measure the resistance according to the value(s) in the table below.
      Text in Illustration 
      *a
      OFF
      *b
      LO
      *c
      M1
      *d
      M2
      *e
      HI
      *f
      Component without harness connected
      (No. 2 Heater Control Sub-assembly)

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      ALL - 5 (E)
      0 (OFF)
      10 kΩ or higher
      9 (LO) - 5 (E)
      1 (LO)
      Below 1 Ω
      9 (LO) - 5 (E) - 7 (M1)
      1 (LO) - 2 (M1)
      Below 1 Ω
      9 (LO) - 5 (E) - 7 (M1)
      2 (M1)
      Below 1 Ω
      9 (LO) - 5 (E) - 7 (M1) - 6 (M2)
      2 (M1) - 3 (M2)
      Below 1 Ω
      9 (LO) - 5 (E) - 6 (M2)
      3 (M2)
      Below 1 Ω
      9 (LO) - 5 (E) - 10 (HI) - 6 (M2)
      3 (M2) - 4(HI)
      Below 1 Ω
      9 (LO) - 5 (E) - 10 (HI)
      4 (HI)
      Below 1 Ω

      If the result is not as specified, replace the No. 2 heater control sub-assembly.

  1. Check that the heater control illuminates.

    1. Apply battery voltage to the heater control sub-assembly and check that the heater control sub-assembly illuminates.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → 2(ILL+)
      Battery negative (-) → 1(ILL-)
      illuminates

      If the result is not as specified, replace the bulb.



4. INSPECT NO. 3 HEATER CONTROL SUB-ASSEMBLY (w/ Heater)


  1. Check the No. 3 heater control sub-assembly resistance.



      E218262E01
    1. Measure the resistance according to the value(s) in the table below.
      Text in Illustration 
      *1
      Rr Defogger Switch
      *a
      MAX HOT
      *b
      Component without harness connected
      (No. 3 Heater Control Sub-assembly)

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      2 (Rr DEF) - 1(E)
      Rear window defogger switch on
      Below 1 Ω
      Rear window defogger switch off
      10 kΩ or higher
      3 (IG) - 6 (MAX-HOT)
      MAX HOT
      Below 1 Ω
      Except MAX HOT
      10 kΩ or higher
      7 (V/B) - 8 (SG)
      Always
      Below 1 Ω

      If the result is not as specified, replace the No. 3 heater control sub-assembly.

    2. Measure the resistance according to the value(s) in the table below (for Cold Area Specification Vehicles).

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      3 (IG) - 6 (MAX-HOT)
      MAX HOT
      Below 1 Ω
      Except MAX HOT
      10 kΩ or higher

      If the result is not as specified, replace the No. 3 heater control sub-assembly.

  1. Check that the rear window defogger indicator.

    1. Connect the positive (+) lead from the battery to terminal 3 (IG) and the negative (-) lead to terminal 1 (E).

    2. Push the rear window defogger switch in and check that the indicator lights up.

      OK:
      Indicator lights up

      1. If the result is not as specified, replace the No. 3 heater control sub-assembly.

  1. Check that the heater control illuminates.

    1. Apply battery voltage to the heater control sub-assembly and check that the heater control sub-assembly illuminates.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → 5(ILL+)
      Battery negative (-) → 4(ILL-)
      illuminates

      If the result is not as specified, replace the bulb.



5. INSPECT NO. 3 HEATER CONTROL SUB-ASSEMBLY (w/o Heater)


  1. Check the No. 3 heater control sub-assembly resistance.



      I107004E01
    1. Using an ohmmeter, measure the resistance variation between connector terminals 7 (A/C) and 8 (SG) when the dial is turned as shown in the illustration.
      Text in Illustration 
      *a
      Component without harness connected
      (No. 3 Heater Control Sub-assembly)

      OK:
      Varies as shown in the illustration

      If the result is not as specified, replace the No. 3 heater control sub-assembly.



    I107005E01
  1. Check that the rear window defogger indicator.
    Text in Illustration 
    *1
    Rr Window Defogger Switch
    *a
    Component without harness connected
    (No. 3 Heater Control Sub-assembly)

    1. Connect the positive (+) lead from the battery to terminal 3 (IG+) and the negative (-) lead to terminal 1 (E).

    2. Push the rear window defogger switch in and check that the indicator lights up.

      OK:
      Indicator lights up

      1. If the result is not as specified, replace the No. 3 heater control sub-assembly.

  1. Check that the heater control illuminates.

    1. Apply battery voltage to the heater control sub-assembly and check that the heater control sub-assembly illuminates.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → 5(ILL+)
      Battery negative (-) → 4(ILL-)
      illuminates

      If the result is not as specified, replace the bulb.