Home › Vehicle Interior › DOOR LOCK › DOOR CONTROL SWITCH

DOOR CONTROL SWITCH > INSPECTION

for Preparation Click here



1. INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (w/o Rear Power Window)


    E221630E01
  1. for LHD:
    Text in Illustration 
    *a
    Component without harness connected
    (Power Window Regulator Master Switch Assembly)
    *b
    LOCK
    *c
    UNLOCK

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      3 (L) - 7 (GND)
      LOCK
      Below 1 Ω
      OFF
      10 kΩ or higher
      9 (UL) - 7 (GND)
      UNLOCK
      Below 1 Ω
      OFF
      10 kΩ or higher

      If the result is not as specified, replace the power window regulator master switch.



    E229491E01
  1. for RHD:
    Text in Illustration 
    *a
    Component without harness connected
    (Power Window Regulator Master Switch Assembly)
    *b
    LOCK
    *c
    UNLOCK

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      1 (L) - 7 (GND)
      LOCK
      Below 1 Ω
      OFF
      10 kΩ or higher
      3 (UL) - 7 (GND)
      UNLOCK
      Below 1 Ω
      OFF
      10 kΩ or higher

      If the result is not as specified, replace the power window regulator master switch.



2. INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (w/ Rear Power Window)


    E229492E01
  1. for LHD:
    Text in Illustration 
    *a
    Component without harness connected
    (Power Window Regulator Master Switch Assembly)
    *b
    LOCK
    *c
    UNLOCK

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      2 (L) - 1 (GND)
      LOCK
      Below 1 Ω
      OFF
      10 kΩ or higher
      9 (UL) - 1 (GND)
      UNLOCK
      Below 1 Ω
      OFF
      10 kΩ or higher

      If the result is not as specified, replace the power window regulator master switch.



    E221629E02
  1. for RHD:
    Text in Illustration 
    *a
    Component without harness connected
    (Power Window Regulator Master Switch Assembly)
    *b
    LOCK
    *c
    UNLOCK

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      2 (L) - 9 (GND)
      LOCK
      Below 1 Ω
      OFF
      10 kΩ or higher
      8 (UL) - 9 (GND)
      UNLOCK
      Below 1 Ω
      OFF
      10 kΩ or higher

      If the result is not as specified, replace the power window regulator master switch.



3. INSPECT DOOR CONTROL SWITCH ASSEMBLY (w/o Power Window)


    E228968E01
  1. Measure the resistance according to the value(s) in the table below.
    Text in Illustration 
    *a
    Component without harness connected
    (Door Control Switch Assembly)
    *b
    LOCK
    *c
    UNLOCK

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    4 (L) - 3 (E)
    LOCK
    Below 1 Ω
    OFF
    10 kΩ or higher
    2 (UL) - 3 (E)
    UNLOCK
    Below 1 Ω
    OFF
    10 kΩ or higher

    If the result is not as specified, replace the door control switch.