Home › Vehicle Interior › HEATING / AIR CONDITIONING › COOLER EXPANSION VALVE

COOLER EXPANSION VALVE > INSTALLATION

for Preparation Click here


NOTICE:
When removing the cooler expansion valve by itself, be sure to install a new cooler expansion valve and new bolt for suction tube sub-assembly.



1. INSTALL COOLER EXPANSION VALVE
  1. Apply sufficient compressor oil to 2 new O-rings and the fitting surfaces of the cooler expansion valve.

    Compressor oil:
    ND-OIL8 or equivalent

  1. Install the 2 O-rings onto the cooler evaporator.

  1. Using a 4 mm hexagon wrench, install a new cooler expansion valve with the 2 hexagon bolts.

    Torque:
    3.5 N*m{ 36 kgf*cm , 31 in.*lbf }



2. CONNECT LIQUID TUBE SUB-ASSEMBLY A
  1. Remove the vinyl tape from liquid tube and the connecting portion of the unit.

  1. Apply sufficient compressor oil (ND-OIL8) to a new O-ring and the connecting part of the liquid tube.

    Compressor oil:
    ND-OIL8 or equivalent

  1. Install the O-ring onto the liquid tube.

  1. Connect the liquid tube to the unit.



3. CONNECT SUCTION TUBE SUB-ASSEMBLY B
  1. Remove the vinyl tape from suction tube and the connecting portion of the unit.

  1. Apply sufficient compressor oil (ND-OIL8) to a new O-ring and the connecting part of the suction tube.

    Compressor oil:
    ND-OIL8 or equivalent

  1. Install the O-ring onto the suction tube.

  1. Securely connect the suction tube to the air conditioning unit.



    I105938
  1. Turn the hook connector in the direction indicated by the arrow in the illustration.

  1. Insert the pipe joints securely into the fitting holes and tighten the new bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }



4. CHARGE REFRIGERANT



I100449E02

HINT:
Charge refrigerant in accordance with the equipment manual.

  1. Perform vacuum purging using a vacuum pump.

  1. Charge refrigerant HFC-134a (R134a).

    SST
    09985-20010   (09985-02010, 09985-02050, 09985-02060, 09985-02070, 09985-02080, 09985-02090, 09985-02110, 09985-02130, 09985-02140, 09985-02150)

    Standard:
    Item
    Refrigerant Charging Amount
    w/o Fan Shroud Ventilation Duct
    330 to 390 g (11.6 to 13.8 oz.)
    w/ Fan Shroud Ventilation Duct
    350 to 410 g (12.3 to 14.5 oz.)

    NOTICE:
    Do not start the engine before charging it with refrigerant as the cooler compressor does not work properly without sufficient refrigerant. This could cause the compressor to overheat.

    HINT:

    1. The relationship between the refrigerant charge amount and the pressure is as follows.


      I105217E04

    2. High Charge Range:
      If the refrigerant is overcharged, the pressure rises on the high-pressure side. High-pressure cut off frequently occurs. This causes insufficient cooling performance and also insufficient compressor lubrication.
    3. Low Charge Range:
      A shortage of refrigerant causes insufficient cooling performance and low circulation of refrigerant oil, which shortens the compressor life. Operation with insufficient coolant raises the refrigerant temperature and causes heat deterioration of the rubber seals and hoses. Cracking and subsequent refrigerant leakage may occur.


    1. Install the caps onto the service valves on the refrigerant line.



5. WARM UP ENGINE

NOTICE:
Warm up the engine at less than 2000 rpm for 1 minute or more after charging it with refrigerant.



6. INSPECT FOR REFRIGERANT LEAK
  1. After recharging the refrigerant gas, check for refrigerant gas leakage using a halogen leak detector.

  1. Perform the operation as follows:

    1. Stop the engine.
    2. Secure good ventilation (the halogen leak detector may react to volatile gases other than refrigerant, such as evaporated gasoline or exhaust gas).
    3. Repeat the test 2 or 3 times.
    4. Make sure that some refrigerant remains in the refrigeration system.
      When the compressor is off: approximately 392 to 588 kPa (4 to 6 kgf/cm2, 57 to 85 psi)

    HINT:
    It is impossible for the above pressure to be maintained if there is leakage.



    I042222E36
  1. Using the halogen leak detector, check the refrigerant line, especially at the connection points, for leakage.
    Text in Illustration 
    *1
    Halogen Leak Detector



    I100587E05
  1. Bring the halogen leak detector close to the drain hose before performing the test.
    Text in Illustration 
    *1
    Drain Hose
    *2
    Halogen Leak Detector

    HINT:
    1. After the blower motor has stopped, leave the cooling unit for at least 15 minutes.
    2. Place the halogen leak detector sensor under the drain hose.
    3. When bringing the halogen leak detector close to the drain hose, make sure that the halogen leak detector does not react to other volatile gases.

    If such a reaction is unavoidable, the vehicle must be lifted up.

  1. If no gas leakage is detected from the drain hose, remove the blower motor from the cooling unit. Insert the halogen leak detector sensor into the unit and perform the test.

  1. Disconnect the pressure switch connector and leave it for approximately 20 minutes. Bring the halogen leak detector close to the pressure switch and perform the test.