ENGINE
Component
|
Fluid, Lubricant, or Genuine Part
|
Engine Coolant
|
Mopar® Antifreeze/Coolant 5 Year/100,000 Mile (161 000 km) Formula HOAT (Hybrid Organic Additive Technology)
|
Engine Oil (3.7/4.7/5.7L Engines)
|
Use API Certified SAE 5W-20 Engine Oil, meeting the requirements of DaimlerChrysler Material Standard MS-6395.
|
Engine Oil (6.1L Engine)
|
Use API Certified SM/CF synthetic engine oil. SAE 0W-40 is recommended, meeting the requirements of DaimlerChrysler Material Standard MS-10725.
|
Engine Oil (3.0L Diesel Engines)
|
Use API Certified SAE 5W-30 Synthetic Engine Oil, meeting the requirements of DaimlerChrysler Material Standard MS-11106 or Mercedes Benz MB 229.51 and ACEA C3 qualified engine oils.
|
Oil Filter (All Engines)
|
Mopar® Oil Filter (P/N 05281090)
|
Oil Filter (3.0L Diesel Engines)
|
Mopar® Oil Filter (P/N 05175571AA)
|
Spark Plugs
|
Refer to the Vehicle Emission Control Information label in the engine compartment.
|
Fuel Selection (3.7L and 4.7L Engines)
|
87 Octane
|
Fuel Selection (5.7L Engines)
|
87 Octane Acceptable - 89 Octane Recommended
|
Fuel Selection (6.1L Engine)
|
Premium Unleaded 91 Octane Only or higher.
|
Fuel Selection (3.0L Diesel Engines)
|
Use only the best quality fuel with a calculated Cetane Index of 50 or higher. In addition, the manufacturer recommends using diesel fuel with a sulfur content of less than 350 ppm.
|
NOTE:
DO NOT use gasolines containing Methanol or E85 Ethanol. Use of these blends may result in starting and driveability problems and may damage critical fuel system components.
|
|
ENGINE - EXPORT
Component
|
Fluid, Lubricant, or Genuine Part
|
Engine Coolant
|
Mopar® Antifreeze/Coolant 5 Year/100,000 Mile (161 000 km) Formula HOAT (Hybrid Organic Additive Technology)
|
Engine Oil - Gasoline (Non ACEA Categories)
|
For best performance and maximum protection under all types of operating conditions, the manufacture only recommends engine oils that are API certified and meet the
requirements of DaimlerChrysler Material Standard MS-6395. Use Mopar or an equivalent oil meeting the specification MS-6395. These Certified Oils exhibit the American Petroleum Institute (API) Engine Oil
Certification Symbol on the front of the oil container. This symbol means that the oil has been tested, certified, and licensed by the American Petroleum Institute (API) to meet the oil standards required
by the manufacturers. The manufacturer only recommends API Certified engine oils that meet the requirements of DaimlerChrysler Material Standard MS-6395.
|
Engine Oil - Gasoline (ACEA Categories)
|
For countries that use the ACEA European Oil Categories for Service Fill Oils, use engine oils that meet the requirements of ACEA A3/B3, A3/B4 or A5/B5.
|
Engine Oil - Diesel
|
For countries that use the ACEA European Oil Categories for Service Fill Oils, use engine oils that meet the requirements of ACEA A3/B4/C3 that is approved to MB 229.31.
|
Spark Plugs
|
Refer to the Vehicle Emission Control Information label in the engine compartment.
|
Fuel Selection (Gasoline Engines)
|
Research octane of 91
|
Fuel Selection (6.1L Engine)
|
Premium unleaded gasoline with a minimum research octane rating of 98.
|
Fuel Selection (Diesel Engines)
|
Use only fuel with a calculated Cetane Index of 50 or higher. In addition, the manufacturer recommends using diesel fuel with a sulfur content of less than 350 ppm.
|
CHASSIS
Component
|
Fluid, Lubricant, or Genuine Part
|
Automatic Transmission
|
Mopar® ATF+4 Automatic Transmission Fluid
|
Transfer Case (3.7L Engine)
|
Mopar® ATF+4 Automatic Transmission Fluid
|
Transfer Case (3.0/4.7/5.7L Engines)
|
Mopar® NV 247/245 Transfer Case Lubricant
|
Transfer Case (6.1L Engine)
|
Mopar® NV146 Transfer Case Fluid. Usage of other fluid/lubricants is NOT recommended.
|
Axle Differential (Front-Rear)
|
Mopar® Synthetic Gear & Axle Lubricant SAE 75W-140 (API-GL5) or equivalent with friction modifier additive.
|
Brake Master Cylinder
|
Mopar® DOT 3 Brake Fluid, SAE J1703 should be used. If DOT 3, SAE J1703 brake fluid is not available, then DOT 4 is acceptable. Use only recommended
brake fluids.
|
Power Steering Reservoir
|
This system requires the use of Mopar® Hydraulic System Power Steering Fluid (P/N 05142893AA) or equivalent, which meets DaimlerChrysler Material Standard
MS-10838.
|
CHASSIS - EXPORT
Component
|
Fluid, Lubricant, or Genuine Part
|
Automatic Transmission (Gasoline Engines)
|
Mopar® ATF+4 Automatic Transmission Fluid
|
Automatic Transmission (Diesel Engines)
|
Shell® 3403 Automatic Transmission Fluid
|
Transfer Case (3.7L Engine)
|
Mopar® ATF+4 Automatic Transmission Fluid
|
Transfer Case
|
Mopar® NV 247/245 Transfer Case Lubricant
|
Transfer Case (6.1L Engine)
|
Mopar® NV146 Transfer Case Fluid or equivalent.
Usage of other fluid/lubricants is NOT recommended.
|
Axle Differential (Front-Rear)
|
Mopar® Synthetic Gear & Axle Lubricant SAE 75W-140 (API-GL5) or equivalent with friction modifier additive.
|
Brake Master Cylinder
|
Mopar® DOT 3 Brake Fluid, SAE J1703 should be used. If DOT 3, SAE J1703 brake fluid is not available, then DOT 4 is acceptable. Use only recommended
brake fluids.
|
Power Steering Reservoir
|
This system requires the use of Mopar® Hydraulic System Power Steering Fluid (P/N 05142893AA) or equivalent, which meets DaimlerChrysler Material Standard
MS-10838.
|
FLUID CAPACITIES
DESCRIPTION
|
U.S.
|
Metric
|
Fuel (Approximate)
|
20.6 Gallons
|
78 Liters
|
3.7/4.7/5.7L Gasoline Engines
|
21 Gallons
|
79 Liters
|
3.0L Diesel Engine
|
22 Gallons
|
83 Liters
|
Engine Oil with Filter
|
|
|
3.7 Liter Engine (5W-30, API Certified)
|
5 Quarts
|
4.7 Liters
|
4.7 Liter Engine (5W-30, API Certified)
|
6 Quarts
|
5.7 Liters
|
5.7 Liter Engine (5W-20, API Certified)
|
7 Quarts
|
6.6 Liters
|
6.1 Liter Engine (SAE 0W-40, API Certified)
|
7 Quarts
|
6.6 Liters
|
3.0 Liter Diesel Engine (SAE 5W-30 Synthetic, API Certified)
|
10 Quarts
|
9.5 Liters
|
Cooling System *
|
|
|
3.7 Liter Engine (Mopar® Engine Coolant/Antifreeze 5 Year/100,000 Mile (161 00 km) Formula)
|
9 Quarts
|
10 Liters
|
4.7 Liter Engine (Mopar® Engine Coolant/Antifreeze 5 Year/100,000 Mile (161 00 km) Formula)
|
14.5 Quarts
|
13.7 Liters
|
5.7 Liter Engine (Mopar® Engine Coolant/Antifreeze 5 Year/100,000 Mile (161 00 km) Formula)
|
14.5 Quarts
|
13.7 Liters
|
6.1 Liter Engine (Mopar® Engine Coolant/Antifreeze 5 Year/100,000 (161 00 km) Mile Formula)
|
14.8 Quarts
|
14 Liters
|
3.0 Liter Diesel Engine (Mopar® Antifreeze/Engine Coolant 5 Year/100,000 (161 00 km) Mile Formula)
|
14 Qts
|
13.2 Liters
|
* Includes heater and coolant recovery bottle filled to MAX level.
|
FLUID CAPACITIES - EXPORT
| |
Metric
|
U.S.
|
Fuel (Approximate)
|
78 Liters
|
20.6 Gallons
|
3.7/4.7/5.7 Liter Engines
|
79 Liters
|
21 Gallons
|
3.0 Liter Diesel Engine
|
83 Liters
|
22 Gallons
|
Engine Oil with Filter
|
|
|
3.7 Liter Engine
|
4.7 Liters
|
5 Quarts
|
4.7 Liter Engine
|
5.7 Liters
|
6 Quarts
|
5.7 Liter Engine
|
6.6 Liters
|
7 Quarts
|
6.1 Liter Engine (SAE 0W-40)
|
6.6 Liters
|
7 Qts
|
3.0 Liter Diesel Engine
|
9.5 Liters
|
10 Quarts
|
Cooling System *
|
|
|
3.7 Liter Engine (Mopar® Antifreeze/Engine Coolant 5 Year/100,000 Mile (161 000 km) Formula)
|
10 Liters
|
9 Qts
|
4.7 Liter Engine (Mopar® Antifreeze/Engine Coolant 5 Year/100,000 Mile (161 000 km) Formula)
|
13.7 Liters
|
14.5 Quarts
|
5.7 Liter Engine (Mopar® Antifreeze/Engine Coolant 5 Year/100,000 Mile (161 000 km) Formula)
|
13.7 Liters
|
14.5 Quarts
|
6.1 Liter Engine (Mopar® Engine Coolant/Antifreeze 5 Year/100,000 Mile Formula)
|
14 Liters
|
14.8 Qts
|
3.0 Liter Diesel Engine (Mopar® Antifreeze/Engine Coolant 5 Year/100,000 Mile (161 000 km) Formula)
|
13.2 Liters
|
14 Quarts
|
* Includes heater and coolant recovery bottle filled to MAX level.
|