ENGINE - EXPORT
Component
|
Fluid, Lubricant, or Genuine Part
|
Engine Coolant
|
Mopar® Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology)
|
Engine Oil - Gasoline (Non ACEA Categories)
|
For best performance and maximum protection under all types of operating conditions, the manufacture only recommends engine oils that are API certified and meet the
requirements of DaimlerChrysler Material Standard MS-6395. Use Mopar or an equivalent oil meeting the specification MS-6395. These Certified Oils exhibit the American Petroleum Institute (API) Engine Oil
Certification Symbol on the front of the oil container. This symbol means that the oil has been tested, certified, and licensed by the American Petroleum Institute (API) to meet the oil standards required
by the manufacturers. The manufacturer only recommends API Certified engine oils that meet the requirements of DaimlerChrysler Material Standard MS-6395.
|
Engine Oil - Gasoline (ACEA Categories)
|
For countries that use the ACEA European Oil Categories for Service Fill Oils, use engine oils that meet the requirements of ACEA A3/B3, A3/B4 or A5/B5.
|
Engine Oil - Diesel (without Particulate Filter)
|
Use only Diesel Engine Oils confirming to API (American Petroleum Institute) Quality CI-4 or CJ-4. For countries that use the ACEA European Oil Categories for Service Fill Oils, use engine
oils that meet the requirements of ACEA A3/B4/C3.
|
Engine Oil - Diesel (with Particulate Filter)
|
Use only Diesel Engine Oils confirming to API (American Petroleum Institute) Quality CI-4 or CJ-4. For countries that use the ACEA European Oil Categories for Service Fill Oils, use engine
oils that meet the requirements of ACEA A3/B4/C3. (LOW ASH)
|
Spark Plugs
|
Refer to the Vehicle Emission Control Information label in the engine compartment.
|
Oil Filter (3.8L Engine)
|
Mopar® Oil Filter (P/N 04105409AC)
|
Oil Filter (2.8L Diesel Engine)
|
Mopar® Oil Filter (P/N 5003558AA)
|
Fuel Selection (Gasoline Engines)
|
91 Octane
|
Fuel Selection (Diesel Engines)
|
50 Cetane (Less than 15 ppm Sulfur)
|
CHASSIS
Component
|
Fluid, Lubricant, or Genuine Part
|
Automatic Transmission
|
Mopar® ATF+4 Automatic Transmission Fluid
|
Manual Transmission
|
Mopar® Manual Transmission Lubricant or equivalent (meeting the requirements of DaimlerChrysler Material Standard MS-9224)
|
Transfer Case
|
Mopar® ATF+4 Automatic Transmission Fluid or equivalent.
|
Axle Differential (Front)
|
Mopar® Gear & Axle Lubricant (SAE 80W-90) (API GL-5) or equivalent.
|
Axle Differential (Rear)
|
198 RBI (Model 35) and 226 RBI (Model 44) - Mopar® Gear & Axle Lubricant (SAE 80W-90) (API GL-5) or equivalent. For trailer
towing, use Mopar® Synthetic Gear & Axle Lubricant (SAE 75W-140) or equivalent. Models equipped with Trac-Lok require an additive.
|
Brake Master Cylinder
|
Mopar® DOT 3 Brake Fluid, SAE J1703 should be used. If DOT 3, SAE J1703 brake fluid is not available, then DOT 4 is acceptable. Use only recommended brake fluids.
|
Power Steering Reservoir
|
Mopar® ATF+4 Automatic Transmission Fluid
|
CHASSIS - EXPORT
Component
|
Fluid, Lubricant, or Genuine Part
|
Automatic Transmission
|
Mopar® ATF+4 Automatic Transmission Fluid
|
Manual Transmission
|
Mopar® Manual Transmission Lubricant or equivalent (meeting the requirements of DaimlerChrysler Material Standard MS-9224)
|
Transfer Case
|
Mopar® ATF+4 Automatic Transmission Fluid or equivalent.
|
Axle Differential (Front)
|
Mopar® Gear & Axle Lubricant (SAE 80W-90) (API GL-5) or equivalent.
|
Axle Differential (Rear)
|
198 RBI (Model 35) and 226 RBI (Model 44) - Mopar® Gear & Axle Lubricant (SAE 80W-90) (API GL-5) or equivalent. For trailer
towing, use Mopar® Synthetic Gear & Axle Lubricant (SAE 75W-140) or equivalent. Models equipped with Trac-Lok require an additive.
|
Brake Master Cylinder
|
Mopar® DOT 3 Brake Fluid, SAE J1703 should be used. If DOT 3, SAE J1703 brake fluid is not available, then DOT 4 is acceptable. Use only recommended
brake fluids.
|
Power Steering Reservoir
|
Mopar® ATF+4 Automatic Transmission Fluid
|