P1239-ENGINE OIL TEMPERATURE TOO LOW
 |
For a complete wiring diagram, refer to the Wiring Information.
-
When Monitored:
The engine oil temperature has dropped below a calibrated temperature value. Engine start up.
-
Set Condition:
The Engine Oil temperature rises slower than a calibrated modeled temperature. When the actual oil temperature falls below the low boundary of the calibrated modeled temperature for three minutes the fault is set. Two trip fault. Three good trips to turn off the MIL.
Possible Causes |
|---|
| ENGINE OIL |
| (G24) EOT SIGNAL CIRCUIT HIGH RESISTANCE |
| (K900) SENSOR GROUND CIRCUIT HIGH RESISTANCE |
| ENGINE OIL TEMPERATURE SENSOR |
| POWERTRAIN CONTROL MODULE (PCM) |
Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. (Refer to 28 - DTC-Based Diagnostics/MODULE, Powertrain Control (PCM) - Standard Procedure).
| NOTE: | Diagnose any CAN C Communication DTCs before continuing. |
| 1. | Turn the ignition off. |
| 2. | If possible, allow the vehicle to sit with the ignition off for more than 60 minutes in an environment where the temperature will allow the oil temperature to cool down. |
| 3. | Start the engine and allow it to reach normal operating conditions. |
| 4. | With the scan tool, select View DTCs. |
Is the status Active or Pending for this DTC?
Yes
- Go To 2
No
- Perform the INTERMITTENT CONDITION diagnostic procedure. (Refer to 28 - DTC-Based Diagnostics/MODULE, Powertrain Control (PCM) - Standard Procedure).
| 1. |
The following conditions must be checked: |
- OEM recommended oil viscosity is being used.
- Customer is following the oil change schedule.
- Check the engine oil for contamination. (i.e., fuel and/or engine coolant).
- Internal engine condition that may effect oil pressure.
Were any of the above conditions found?
Yes
- Repair as necessary.
- Perform the POWERTRAIN VERIFICATION TEST. (Refer to 28 - DTC-Based Diagnostics/MODULE, Powertrain Control (PCM) - Standard Procedure).
No
- Go To 3
3. ENGINE OIL TEMPERATURE SENSOR VOLTAGE
| 1. | Turn the ignition off. |
| 2. | Disconnect the Engine Oil Temperature Sensor harness connector. |
| 3. | Turn the ignition on. |
| 4. | With the scan tool, read the Engine Oil Temperature Sensor voltage. |
| NOTE: | The sensor voltage should be approximately 5.0 Volts (plus or minus .1 Volt) with the connector disconnected. |
Does the scan tool display the voltage as described above?
Yes
- Go To 4
No
- Go To 5
4. ENGINE OIL TEMPERATURE SENSOR
 |
| 1. | Turn the ignition off. |
| 2. | Connect a jumper wire between the (G24) EOT Signal circuit and the (K900) Sensor Ground circuit in the Engine Oil Temperature Sensor harness connector. |
| 3. | Turn the ignition on. |
| 4. | With the scan tool, read the Engine Oil Temperature Sensor voltage. |
| NOTE: | The sensor voltage should be approximately 0.0 Volts (plus or minus .1 Volt) with the jumper wire in place. |
Does the scan tool display the voltage as described above?
Yes
- Replace the Engine Oil Temperature Sensor.
- Perform the POWERTRAIN VERIFICATION TEST. (Refer to 28 - DTC-Based Diagnostics/MODULE, Powertrain Control (PCM) - Standard Procedure).
No
-
Go To 5
5. (G24) EOT SIGNAL CIRCUIT HIGH RESISTANCE
| 1. | Turn the ignition off. |
| 2. | Disconnect the PCM C2 harness connector. |
Do not probe the PCM harness connectors. Probing the PCM harness
connectors will damage the PCM terminals resulting in poor terminal
to pin connection. Install the GPEC Diagnostic Adaptor to perform
the diagnosis.
CAUTION:
| 3. | Connect the Adapter, GPEC Diagnostic 10436 . |
| 4. | Measure the resistance of the (G24) EOT Signal circuit between the Engine Oil Temperature Sensor harness connector and the GPEC Adaptor. |
Is the resistance below 5.0 Ohms?
Yes
- Go To 6
No
- Repair the (G24) EOT Signal circuit for high resistance.
-
Perform the POWERTRAIN
VERIFICATION TEST. (Refer to
28 - DTC-Based Diagnostics/MODULE, Powertrain Control (PCM)
- Standard
Procedure).
6. (K900) SENSOR GROUND CIRCUIT HIGH RESISTANCE
| 1. | Measure the resistance of the (K900) Sensor Ground circuit between the Engine Oil Temperature Sensor harness connector and the GPEC Adaptor. |
Is the resistance below 5.0 Ohms?
Yes
- Go To 7
No
- Repair the (K900) Sensor Ground circuit for high resistance.
-
Perform the POWERTRAIN
VERIFICATION TEST. (Refer to
28 - DTC-Based Diagnostics/MODULE, Powertrain Control (PCM)
- Standard
Procedure).
7. POWERTRAIN CONTROL MODULE (PCM)
| 1. | Using the wiring diagram/schematic as a guide, inspect the wiring and connectors between the Engine Oil Temperature Sensor and the Powertrain Control Module (PCM). |
| 2. | Look for any chafed, pierced, pinched or partially broken wires. |
| 3. | Look for broken, bent, pushed out or corroded terminals. |
| 4. | Monitor the scan tool data relative to this circuit and wiggle test the wiring and connectors. |
| 5. | Look for the data to change or for the DTC to reset during the wiggle test. |
| 6. | Perform any Technical Service Bulletins that may apply. |
Were any problems found?
Yes
- Repair as necessary.
- Perform the POWERTRAIN VERIFICATION TEST. (Refer to 28 - DTC-Based Diagnostics/MODULE, Powertrain Control (PCM) - Standard Procedure)
No
- Replace and program the Powertrain Control Module in accordance with the service information. (Refer to 08 - Electrical/8E - Electronic Control Modules/MODULE, Powertrain Control - Removal) .
- Perform the POWERTRAIN VERIFICATION TEST. (Refer to 28 - DTC-Based Diagnostics/MODULE, Powertrain Control (PCM) - Standard Procedure).